Page 1
Owner's Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model number: Serial number:...
Important Information WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock.
Introduction ... 4 Welcome to Toshiba ... 4 Exploring your new TV ... 4 Connecting your TV ... 5 Connecting a VCR ... 5 Connecting a cable converter box ... 6 Connecting a cable converter box and VCR ... 6 Connecting a DVD player or satellite receiver and a VCR ...
The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible. This manual applies to models 34HF81 and 34HF81C. Before you start reading, check your model number on the back of the TV.
Connecting your TV If you have not connected electronic equipment before, or you have been frustrated in the past, you may wish to read this section. (Cables are not supplied.) • A coaxial cable is the standard cable that comes in from your antenna or cable converter box.
Connecting a cable converter box This connection allows you to watch basic and premium cable channels. To use the TV’s features, select ANT-1. To view premium channels, select ANT-2, tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.
Connecting a DVD player or satellite receiver and a VCR This connection allows you to watch DVD/satellite, VCR, and TV programs, and record one TV channel while watching another channel. You will need: • one coaxial cable • two pairs of audio cables (one single and one pair of audio cables for a mono VCR) •...
DVD and TV programs. You can record from one source while watching a program from another source. Your TV has ColorStream component video inputs. Connecting your TV to a ColorStream-compatible DVD player (such as a Toshiba ColorStream-equipped DVD player) can greatly enhance picture quality and realism.
Connecting a DTV receiver/set-top box (with or without ColorStream™) and a VCR This connection allows you to watch DTV (digital TV broadcast), VCR, and TV programs, and record DTV and TV programs. You can record from one source while watching a program from another source.
Connecting two VCRs This connection allows you to record (dub/edit) from one VCR to another VCR while watching a videotape. You can also record from one TV channel while watching another TV channel. You will need: • one coaxial cable •...
Connecting an audio system This connection allows you to use an audio amplifier to adjust the audio level. This also allows you to use external speakers. To control the audio, turn on the TV and the stereo amplifier, and turn off the built-in speakers (see “Turning off the built-in speakers” on page 49).
Using the remote control Preparing the remote control for use Your Toshiba TV remote control has one dedicated TV mode and five universal modes: VCR, Cable/SAT, DVD, Audio1, and Audio2. The target devices and default devices being programmed for each mode...
Remote Control functional key chart Toshiba TV Cable Key Label (TV) (CBL/SAT) (CBL/SAT) LIGHT Lights the remote key, and toggles between enabled and disabled Illumination mode. SLEEP Sleep timer --- POWER Power Power 1/MOVIE Digit 1 Digit 1 2/SPORTS Digit 2...
Page 14
Toshiba TV Cable Key Label (TV) (CBL/SAT) (CBL/SAT) TV/VCR Bypass A/B AM/FM DISC --- STOP PIP CH POP channel up/down POP on/off MULTI This button is not available for this TV model or any other device connected to this TV.
Programming the remote control for use with your audio/video devices Device code setup 1. Refer to the Device code table on pages 17 – 20 to find the code for the brand of your device. If more than one number is listed, try each one separately until you find the one that works.
Verifying the device code (990) Use this feature to verify the codes for your other devices. The number of blinks after pressing the 1, 2, 3, and 4 buttons is the 4- digit code set up for that mode. For example, to verify the device code of the VCR: 1.
Learning about the remote control The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the “Remote Control functional key chart” on pages 13 –14. turns the TV on and off POWER allows access to the automatic TV shut-off function (page 45) SLEEP...
Setting up your TV Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the TV using the menu. You can access the menu using the buttons on your TV or remote control.
Changing the on-screen display language Choose from three different languages (English, French and Spanish) for the on-screen display of adjustment menus and messages. To select a language: 1. Press MENU, and then press x or • until the SET UP menu appears.
Adding channels to the TV’s memory When you press Channel y or z, your TV will stop only on the channels stored in the TV’s channel memory. Follow the steps below and on the next page to program all active channels into the TV’s memory.
Using the TV’s features Adjusting the channel settings Switching between two channels You can switch between two channels without entering an actual channel number each time. To switch between two channels: 1. Select the first channel or video mode you want to view. 2.
To clear a favorite channel: 1. Press MENU, and then press x or • until the CUSTOM menu appears. 2. Press y or z to highlight FAVORITE CH2, for example. 3. Press x or • to display the FAVORITE CH2 menu. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 CUSTOM T I MER...
Page 28
4. Press the Channel Number buttons to select a channel you want to label. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 CUSTOM T I MER 0 0 0...
Viewing the wide-screen picture formats You can view programs that have the conventional TV picture format (4:3 aspect ratio) and the wide-screen format (16:9 aspect ratio) in a variety of picture sizes. Selecting the picture size Repeatedly press PIC SIZE to select either Nomal, Theater Wide 1, Theater Wide 2, Theater Wide 3, or Full picture size, as described below.
Page 30
Conventional picture on a conventional TV screen Theater Wide 1 (recommended mode): • The picture is non-uniformly enlarged—the center of the picture remains close to its true proportion, but the left and right edges are stretched wider to fill the screen. •...
Scrolling the Theater Wide picture (Theater Wide 2 and 3 only) 1. Press PIC SIZE to select the Theater Wide 2 or 3 mode. 2. Press MENU, and then press x or • until THEATER menu appears. 3. Press y or z to highlight PICTURE SCROLL. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 THEATER FOCUS...
Using the POP double-window feature The POP (picture-out-picture) feature splits the screen into a double window that allows you to watch two programs at the same time. The POP program can come from a TV broadcast or an external source, such as a VCR.
Switching the main and POP pictures Press SWAP while you are using the POP feature to switch the main and POP pictures. Freezing the POP picture Press STILL while you are using the POP feature. The POP picture will become a still picture. To return to the moving picture, press STILL again.
Using the LOCKS menu The LOCKS menu includes the V-Chip, CH Lock, Video Lock, and New PIN Code functions. You can use these functions after entering the correct PIN code. Entering the PIN code 1. Press MENU, and then press x or • until the LOCKS menu appears.
Using the V-CHIP menu Some TV programs and movies include signals that classify the content of the program (violence, sex, dialog, language). The V-CHIP control feature in this TV detects the signals and blocks the programs according to your selections. To use this feature, perform the following setup.
MPAA RATING (Independent rating system for movies) 1. From the LOCKS menu, select MPAA RATING. 2. Press x or • to display the MPAA RATING menu, then press z or y to highlight MPAA RATING. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 LOCKS MPAA RAT I NG NC1 7...
Unlocking programs temporarily 1. If you try to watch a TV program that exceeds the rating limits you set, the TV enters program lock mode. After 4 seconds, the TV starts the favorite channel search function (see page 33). You can either unlock the program temporarily (see steps 2-4) or select a non-locked program to watch.
To unlock channels: 1. From the LOCKS menu, select CH LOCK. 2. Press x or • to display the CH LOCK menu. 3. Press yzx • to highlight the channel you want to unlock, then press ENTER. LOCKS V CH I P ENABLE BLOCK I NG TV RAT...
Using the front panel lock feature Lock the front panel buttons to prevent the buttons from being pressed accidentally (by children, for example). When the front panel lock is in ON mode, all control buttons on the TV front panel (except POWER) do not operate.
Adjusting the picture Selecting the picture mode You can select your desired picture type from four picture modes: Sports, Standard, Movie, and Preference. Mode Picture Quality Sports Bright and dynamic picture (factory setting) Standard Standard picture setting (factory setting) Movie Movie-like picture setting (factory setting) Preference Your personal preference*...
Saving new preference You can save the PICTURE qualities (contrast, brightness, color, tint, and sharpness) you adjusted in the picture preference mode. To save your new preferences: 1. Press MENU, and then press x or • until the PICTURE menu appears.
Selecting the cinema mode When you view a DVD movie (3-2 pulldown processed) from a DVD player connected to the ColorStream (component video) inputs on the TV, smoother and more natural motion can be obtained by setting the CINEMA MODE to FILM (auto). To select the CINEMA MODE to FILM (auto): 1.
Selecting the video input source Press INPUT on the remote control or TV/VIDEO on the TV to view a signal coming from another device connected to your TV, such as a VCR or video disc player (see illustrations below). You can select ANT 1, VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD1, ColorStream HD2, or ANT 2 depending on which input jacks are used for connecting the devices (see “Connecting your TV”...
Using the closed caption feature The closed caption feature has two options: • Captions—An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as “CC” in TV listings). • Text—An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations).
Setting the sleep timer To set the sleep timer to turn the TV off automatically: 1. Press SLEEP to set the length of time until the TV turns off. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 T I MER 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Every time you press the button, the time display will increase by...
Adjusting the sound Muting the sound Press MUTE to temporarily turn off the sound. While the sound is off, the screen will display the word “1/2 MUTE” or “MUTE” in the lower right corner. Every time you press the button, the mute mode will change in the following order.
Using the WOW surround sound feature The WOW surround sound feature expands the audio listening field wider and deeper to create exceptional sound quality from the TV’s speakers. WOW consists of the three features: SRS 3D, FOCUS and TruBass, being turned on. The feature uses stereo signals from a TV broadcast or video input.
Turning off the built-in speakers Use this feature to turn the TV speakers off when you connect an audio system (see “Connecting an audio system” on page 11). To turn off the built-in speakers: 1. Press MENU, then press x or • until AUDIO menu appears. 2.
Using the StableSound feature When the signal source is changed, the stable sound feature limits the high volume level to prevent extreme changes in volume (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial). To turn on the StableSound feature: 1.
Viewing the demonstration mode The demonstration mode is an option available in the MENU button on the TV front panel that will demonstrate several of your TV’s features. To start the demo: Press and hold MENU on the TV for 4 seconds. To stop the demo: Press RECALL, EXIT, or POWER.
Appendix Specifications Television System Channel Coverage Power Source Power Consumption Audio Power Speaker Type Video/Audio Terminals Dimensions Mass Supplied Accessories Design and specifications are subject to change without notice. NTSC standard VHF: 2 through 13 UHF: 14 through 69 Cable TV: Mid band (A-8 through A-1, A through I) Super band (J through W) Hyper band (AA through ZZ, AAA, BBB) Ultra band (65 through 94, 100 through 125)
Troubleshooting Before calling a service technician, please check the following table for a possible cause of the problem and some solutions. Problem TV will not turn on No picture, no sound No sound, picture OK Poor picture, sound OK Poor reception of broadcast channels Cannot receive above channel 13 Black box appears on the screen Unable to select a certain channel...
ATTENTION CANADIAN CONSUMERS: Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Products purchased in the U.S.A. and used in Canada are not covered by these warranties.
Index A/V receiver connection ... 11 ANT 1/2 ... 23 Antenna cables ... 5 Audio cables ... 5 AUDIO OUT sound, selecting ... 49 Audio system connection ... 11 Auto power off ...51 BACKGROUND selection ...50 Back of the TV ... 4 Cable converter box connection ...
Page 56
VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C. V6W 1J5, CANADA TEL: (604) 303-2500 MANUFACTURED BY TOSHIBA VISUAL-EQUIPMENT CORPORATION ColorStream is a registered trademark of Toshiba Corporation. StableSound is a trademark of Toshiba America Consumer Products, Inc. PRINTED IN JAPAN (01-08) 23565334A...