Toto Link CP900 User Manual

Toto Link CP900 User Manual

Wireless outdoor cpe

Advertisement

User Guide
Wireless Outdoor CPE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CP900 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Toto Link CP900

  • Page 1 User Guide Wireless Outdoor CPE...
  • Page 3: Table Of Contents

    Contents About This Guide 1. Overview Introduction 2. LED Indicators 3. Ports and Buttons 4. Passive PoE Box 1. Connection and Installation Hardware Installation 2. ESD and lightning Protection 1. PC Setttings Easy Setup Guide 2. Web Interface Login 3. Working Modes 1) AP Mode 2) Client Mode 3) Repeater Mode...
  • Page 4: About This Guide

    About This Guide This guide contains information for introduction and setup of TOTOLINK Wireless Outdoor CPE series. Please read this guide carefully before operation. When using this guide, please notice that feature of the product may vary slightly depending on your location, language and Internet service provider. All screenshots, images, parameters and descriptions documented in this guide are used for demonstra- tions only.
  • Page 5: Introduction

    Introduction TOTOLINK Wireless Outdoor CPEs are designed to provide cost-effective solution for 1. Overview outdoor long range Wi-Fi coverage. With built-in polarized antennas, high power output and multiple working modes, TOTOLINK CPEs are used extensively in many applications. Powered by Passive PoE also makes the network cabling more easy and �lexibly.
  • Page 6: Ports And Buttons

    3. Ports and Buttons GND LAN(POE IN) RESET RESET LAN1 RESET (POE IN) LAN1 (POE IN) Ports and Buttons Description This GND port is used to connect electrical ground for ESD and lightning protection. This RJ45 Port is used to connect PoE box for both power LAN(POE IN)...
  • Page 7: Passive Poe Box

    4. Passive PoE Box POE box POE box front back Ports and Buttons Description DATA IN This RJ45 port is used to connect PC for data input The DC IN socket is where you will connect the power DC IN adapter.
  • Page 8: Hardware Installation

    Hardware Installation 1. Connection and Installation Step 1. Open the sliding closure on the CPE to plug into the Ethernet cable. This may not easy because the sliding closure is fasten on in case it will come off when CPE works outdoors.
  • Page 9 Connection diagram: Switch Wall socket Laptop POE box Router Step 2. After the Ethernet cable connection, push up the sliding closure to make it fasten again on the case. Step 3. Fix the CPE to the pole by strips, then adjust it to face the Wi-Fi coverage area(see left-hand side).
  • Page 10: Esd And Lightning Protection

    2. ESD and lightning Protection For outdoor devices, it is significant to do the grounding for lightning. If your wireless CPE has a GND port, please connect the port to the earth terminal of the building by yellow & green double color line for grounding, see below. Otherwise, we suggest you use lightning protection device for signal.
  • Page 11: Pc Setttings Easy Setup Guide

    Easy Setup Guide 1. PC Settings(for Windows 8) After hardware connection, please setup the network parameters of your PC. 1)Click “Start—Control Panel—Network and Sharing Center—Change adapter setting”, right-click “Ethernet”, and choose “Properties”. 2)Double-click “Internet Protocol Version 4 (TCP/IPv4)”.
  • Page 12: Web Interface Login

    3)Choose “Use the following IP address”, input the IP address in the same network segment with your router’s default IP address, as below, then click “OK”. 192 . 168 . 0 . 11 255 . 255 . 255 . 0 2.
  • Page 13: Working Modes

    admin admin 4)Login to the Web interface successfully. First you will see the Easy Setup page. TOTOLINK_5G_222222 totolink 3. Working Modes TOTOLINK CPE supports multiple working modes to satisfy diversi�ied network requirement including AP Mode, Client Mode, Repeater Mode and WISP Mode.
  • Page 14 Scenario 1 Router Switch Server Switch Switch Campus network Smart phone Laptop Access Point Tablet...
  • Page 15 Scenario 2 WISP LAN: 192.168.0.254 WAN: Dynamic IP WISP LAN: 192.168.0.254 WAN: PPPoE Access Point LAN: 192.168.7.2 Router LAN: 192.168.7.1 WISP LAN: 192.168.0.254 WAN: Static IP Scenario 3 IP Camera Access Point LAN: 192.168.0.254 Access Point LAN: 192.168.0.2...
  • Page 16 Connect two of�ice areas LAN: 192.168.0.254 Access Point Switch Switch Access Point LAN: 192.168.0.2 Of�ice Network Of�ice Network AP Settings 1)Go to the CPE’s Easy Setup page. 2)Choose “AP Mode”, setup the CPE’s SSID, Channel and Key(pass word), click Finish. TOTOLINK_5G_222222 totolink 3)...
  • Page 17: Client Mode

    2) Client Mode Scenario 1 IP Camera Access Point LAN: 192.168.0.254 Client LAN: 192.168.0.2 Connect two of�ice areas Access Point LAN: 192.168.0.254 Switch Switch Client LAN: 192.168.0.2 Of�ice Network Of�ice Network Client Settings 1)Go to CPE’s Easy Setup page. 2)Choose “Client Mode” , clice “Scan” to check all available wireless networks around.
  • Page 18: Repeater Mode

    TOTOLINK_RPT_5G 3 ) Choose the SSID you need to connect. Enter correct key, click “Finish”. TOTOLINK_5G_6C8FE3 WPA2-PSK totolink TOTOLINK_5G_6C8FE3 3) Repeater Mode...
  • Page 19 Scenario 1 SSID: abc 智能手机 SSID: abc 笔记本电脑 平板电脑 智能手机 Repeater LAN: 192.168.7.3 笔记本电脑 SSID: abc 平板电脑 智能手机 Router Access Point LAN: 192.168.7.1 LAN: 192.168.7.2 笔记本电脑 平板电脑 Repeater LAN: 192.168.7.4 Scenario 2 SSID: abc SSID: abc IP Camera Access Point LAN: 192.168.0.254 Repeater Repeater...
  • Page 20 TOTOLINK RPT_5G 3)Select the SSID that you want to connect, enter correct key. Then click “Next” to setup the expanded network parameters. TOTOLINK_5G_6C8FE3 WPA2-PSK totolink TOTOLINK_5G_6C8FE3 4 ) Setup the expanded network SSID and password. Click “Finish”.
  • Page 21: Wisp Mode

    TOTOLINK_5G_CPE 88888888 5)Now setup your PC’s LAN card IP address to “Obtain the IP address automatically.” Or you can access the Wi-Fi network through wireless devices. 4) WISP Mode Scenario 1 WISP Smart phone Laptop LAN: 192.168.0.254 Tablet AP Client Router WAN: PPPoE/Dynamic IP/Static IP...
  • Page 22 WISP Settings 1 ) Go to CPE’s Easy Setup page. 2)Choose “WISP Mode”, click “Scan”, the device will check all available ISP wireless networks around. TOTOLINK PRT_5G 3)Select the ISP Wi-Fi you need to connect. Enter correct Key. Then click “Next”. TOTOLINK_5G_6C8FE3 WPA2-PSK totolink...
  • Page 23 ① DHCP, the device will obtain IP address from ISP router automatically. Click 4)Choose WAN Method: “Next” to setup the CPE’s wireless parameters. ② If your ISP provides static IP address, please choose “Static IP”, and input corresponding parameters, click “Next” to setup the wireless parameters.
  • Page 24 ③ PPPoE, please input the User Name and PASSWORD provided by your ISP, click “Next” to setup the wireless parameters. PPPOE 5)Setup the SSID and Key, click “Finish”. TOTOLINK_5G_CPE 88888888 6)Now setup your PC’s LAN card IP address to “Obtain the IP address automatically.” Or you can access the Wi-Fi network through wireless devices.
  • Page 25 Speci�ications Model No. CP900 Hardware Interface 1*LAN1(POE IN) RJ45 Port Button 1*RESET Button Indicators 1*Power,1*LAN,4*Signal Strength Power Supply 24V Passive PoE 6KV Lightning Protection Reliability 15KV ESD Protection IP65 level dustproof and waterproof Circuit Watch-dog circuit Dimensions(L X W X H)...
  • Page 26: Faq

    1. How to reset the CPE to factory default Settings? Keep the CPE powered on, press the RESET button on CPE or Passive PoE box about 8 seconds, the CPE will restore to factory default settings. POE box RESET LAN1 (POE IN) RESET RESET on PoE box...

Table of Contents