NEW TRIBE
WARNING: For tree climbing only. This activity is dangerous. Understand and accept the risks involved before participating. You are responsible
for your own actions and decisions. Before using this product, read and understand all instructions and warnings that accompany it and familiar‐
ize yourself with its capabilities and limitations. We recommend that every user seek qualified instruction in the use of this equipment.
NFPA Standard 1983 recommends separating the user instructions from the saddle and retaining them in permanent record. The standard also recommends making
a copy of the instructions to keep with the saddle and that the instructions should be referred to before and after each use.
Rope bridge
PUTTING ON THE SADDLE
(1) Open the buckle on the waist cinch strap.
(2) Hold the belt facing forward and step into it. Step into the leg straps making sure they are without twists and that the leg pads are at the
back of your thighs with the camouflage side out.
(3) Raise the belt into position at your waist at about the level of your navel. Close the cinch strap buckle and pull the webbing snug.
If you want the leg straps to open, pull the webbing out of the adjuster buckles. When closing them again, check that the floating retainer is in
place before threading the webbing back into the buckle. Leave at least a 3 inch tail of webbing beyond the buckle.
ADJUST THE FIT OF THE SADDLE
Adjust the fit of your saddle so that your body is supported with weight evenly distributed between belt and leg straps, balanced to hang upright and relaxed, and
without uncomfortable pinching or pressure. Fit the saddle before your first climb in it, where you can hang on rope close to the ground. Make and test small ad‐
justments until it feels right. You only have to do this once. Your settings will stay until you change them.
BUTT STRAP ADJUSTMENT
the straps all the way. Move the leg pads to a comfortable position where your balance is good. Then pull on the ends of the butt straps to take
out the slack.
LEG STRAP ADJUSTMENT
BRIDGE STRAP ADJUSTMENT
Failure to read and follow these warnings can result in severe injury or death!
USER INSTRUCTIONS
Rear safety
loop
Leg strap
buckle
Butt straps
Leg pads
The cinch strap on the belt holds the saddle in position on your body. To open the buckle, squeeze the sides. To close,
push the two parts together until they click. (You can silence the sound of this buckle with careful handling.)
LEG STRAP ADJUSTER BUCKLE
The leg strap adjuster buckle grips the leg strap webbing firmly so it will not slip accidentally. The straps are
designed to be adjusted and used without opening them. But if you want to open the straps, you can. To do
so, push the webbing into the buckle, from below, to create a loop as shown, then pull the loop out to free
the webbing from the buckle.
LEG STRAP FLOATING RETAINER
The leg straps move freely through the bridge hardware on the belt. Shown here is the small floating re‐
tainer that keeps the motion under control. It floats down the strap when the saddle is slack. During a
climb, it will ride near the top of the strap. Note: The retainer can slip off if you have opened the leg straps.
Check that the webbing is threaded through this retainer when you close the straps. However, the retainer
is not required for safety. Some climbers prefer to remove it if they like the motion better without it.
The butt straps run between the belt and the leg pads in back and are controlled by two
buckles. Set the position of the leg pads at a point between your knees and your butt where
they give good support and comfort to your thighs without causing the straps to bind at the
crotch.
To adjust: Hang in the saddle. At the back of the belt, lift the tab on each buckle to lengthen
The leg strap adjuster buckle grips the webbing snugly so it will not slip accidentally. To make an adjust‐
ment, push the webbing into the buckle to create a loop as shown. To shorten the strap, push from above
the buckle and pull out the slack from below. To lengthen it, push from below and pull out the slack from
above. Be sure to leave a 3 inch tail of webbing below the buckle for safety. Note: The leg straps are in‐
tended to be loose on your thigh. Some climbers prefer a close fit, which is okay if the saddle feels right that
way. The best length puts the leg straps in balance with the belt so that you sit comfortably upright and
relaxed in the saddle while suspended on rope.
The saddle bridge hardware is attached to the belt by a webbing strap that passes through the hardware
and back to the buckle. You can set the distance of the bridge from your body by adjusting the length of
this webbing. Once the setting is right, you can slide the buckle forward to create a snug eye around the
bridge hardware.
TREE CLIMBING SADDLE
Page 1 of 4
Rigging plate
Bridge strap
Side D
Leg straps
Gear loop
Rigging plate
Side D
Gear Loop