Odys Windesk 9 Plus 3G Quick Start Manual

Introduction
Please observe the information and warnings from the user manual.
‐ Please refer to the user manual for detailed instructions, conformity and support information.
‐ The manual can be found at http://www.odys.de/web/tablet‐pc‐wintab_de.html.
‐ Use the hyperlink at „Einstellungen – PC und Geräte – PC‐Info".
‐ There you will also find a guide on how to change the system language.
‐ Use the installation assistant to easily configure the device.
Important! Please note: In order to use all features available, a Microsoft user account must be created and it is
necessary to activate your system later on. To reset a forgotten password please visit www.live.com.
To prevent conflicts with other systems we recommend creating a new account.
Please close unused apps to extend the battery lifetime as described on the right.
Turn off the tablet when not in use.
Turning On/Off
To turn on the device, press and hold the [Power] button on the device until you see the boot screen and then
release the button. It may take a few minutes to start up the system, please wait before you proceed.
To turn off the device, press and hold the [Power] button until you see the turn off picture.
Drag down the picture as indicated.
Tip: This device will go into the sleep mode and the display will switch off if inactive for a few seconds. Press the
[Power] button briefly to turn on the display and to wake the device. Swipe the lock screen upwards to unlock the
device.
Power On/Off the Display
‐ Press the [Power] button briefly to turn off the display.
‐ Press the [Power] button briefly to turn on the display again.
Getting started
1. Rear Camera
Rear‐facing camera for taking pictures.
2. Power Button
Press and hold the [Power] button to turn the device on or off; press the button
briefly to turn the screen on or off. Should the device stop functioning or operate
abnormally, press and hold for 15 seconds to reset the device off.
3. Volume key + / ‐
Press briefly to increase / decrease the volume level.
4. SIM
Accommodates any Nano‐SIM Card.
5. Windows Key Return to the start screen
6. Micro SD Card Slot
For use with standard Micro SD/SDHC memory card.
7. Headphone Jack Audio output connection for headphones.
Note: The integrated speaker is automatically disabled when headphones are
connected to the device.
8. Micro HDMI
Connect to a TV or other display.
9. Micro USB
Support for USB stick, Surf stick, Keyboard and Mouse.
Charge and power the tablet with the included power adapter.
Note: An OTG supporting adapter cable is required (optional)
10. USB
Support for USB stick, Surf stick, Keyboard and Mouse.
11. Speaker
12. Front Camera Front‐facing camera for taking avatar pictures.
13. Status Indicator
Stays red during charging and will to blue when the battery is fully charged.
14. Microphone
15. Docking Clip
To align the tablet.
16. Docking
To connect an optional available keyboard.
Charging the battery
The device has a built‐in rechargeable battery. No additional battery installation is required. Please charge the
device when the device indicates low battery. To charge the battery, connect the device to any standard wall
outlet using the power adapter.
Note:
a. We advise to use only the supplied power adapter with this device.
b. You can operate the device even while it is being charged. However, for extended battery life, we suggest
"NOT" to use the device while it is charging. We also recommend fully charging the battery when it is
completely empty. We do not recommend partial charging as this may shorten the battery life time.
c. It is recommended to charge the battery before using the device for the first time.
d. For maximum performance, lithium‐ion batteries need to be used often. If you don't use the device often, be
sure to recharge the battery at least once per month.
e. Should the rechargeable battery of the device discharge completely, connect the device (using the adapter) to
the main power source for approximately 5‐10 minutes before attempting to use the device.
f. In some cases, devices which have been charged for longer periods of time may not be able to be switched back
on. Should this occur please do a "reset".
Connect via USB
Note: Only use a USB cable with a maximum length of 100cm. Please
make sure when connecting the USB adapter into the USB socket that
the connector alignment are correct. Incorrect insertion may cause
damage to the plug and socket.
On one side of the plug there are usually small sizes of hooks that secure
the fixation. Pay special attention to the position of the hooks, they
should show upwards when connecting the cable into the socket while
the device is lying on screen up.
In order to view or playback files, these must first be downloaded from
the internet or transferred from a computer and stored on the device
via MircoSD card or USB‐Stick.
ATTENTION: A direct connection between the Device and Computer, via USB‐Cable is not possible!
ODYS Windesk 9 Plus 3G – KURZANLEITUNG
Factory reset
Should you notice unusual behavior or the device cannot be activated, we suggest restoring the device to the
factory settings. Switch off the device. While pressing the Power Button and the Volume‐Minus key
simultaneously, start the device until the Recovery Mode is started. Follow the instructions under
"Troubleshoot" or "Problem Solving". Select „Reset your PC" or "Restore"
ATTENTION! All data and settings will be erased.
Using Micro SD/SDHC memory card
This device can read files directly from memory card and USB memory.
Open the micro SD and micro SIM card compartment on the backside
of the device. To access the files stored, open the app "OneDrive" by
tapping the corresponding icon and select the desired directory. Once
opened, tap the menu "OneDrive" to switch between local and online
storage.
- Check that the Micro SD card is in the correct position with the
- Push the Micro SD card into the card slot until it clicks (If you have a hard time pushing it in, please check if
- To remove Micro SD card, push the card once until it clicks and pops out a little bit.
Note: We recommend using only Micro SD/SDHC cards up to 64GB capacity.
- Should a Micro SD card be inserted into device, it may take a few seconds to update the contents.
- Please avoid inserting or ejecting Micro SD card when other operations are running.
- Do not remove the card if the contents inside the card are in use or if files are being saved to the card.
- Please use your fingernails to properly insert or remove the card.
Using a Nano SIM card



Please note: Be sure to power off to the unit
before inserting the SIM otherwise the card
will not be detected.
Connecting to the Internet
(1)
(2)
(3)
Note:
If there is no internet connection please recheck this setting and verify that you are connected to an avilable wifi or
3G Network.
Support
On our website you will find the latest information about this product, other products of our enterprise, our
company itself and valid warranty terms. The latter you will find under Service ‐ Downloads.
Axdia International GmbH
Formerweg 9
D‐47877 Willich (Germany)
Support‐Hotline (9.00am – 1.00pm):
E‐Mail: support@odys.de
Note
Please address any further questions directly to our Customer Service Department at the following e‐mail
address: support@axdia.de
In order to be able to process your request quickly, we ask you to have the following information ready:
‐ Product description
‐ Purchase date
‐ Description of problem
contact pins facing in direction of the screen as illustrated. You may
damage the card and the SD card slot if the Micro SD card is not
inserted correctly.
you have inserted it correctly).
First, open the card slot using the
enclosed tool or a paperclip.
Insert the paperclip, as illustrated, into
the opening of the card tray eject button
until a small portion of the tray is visible.
Remove the tray from the device. The
card tray eject button is a small round
opening in the card cover.
Insert the Nano‐SIM card into the reader
as illustrated.
Make sure that the Nano‐SIM card is
aligned correctly. The contacts of the
inserted SIM card must point
downwards and the rounded corners
outwards. Damage may occur to the
card or card reader if the SIM card is not
properly inserted into the device.
Push the tray with the inserted SIM card
back into the device until it flushes with
the housing.
Swipe with your finger from the right‐hand side towards the centre and open the function bar like this.
Touch the icon to open All settings and select „Network and Internet".
Tap on the network you wish to connect to and then tap on "Connect". Your Tablet will now attempt to
establish a connection to that 3G network. If the connection is successful, the message "Connected" will
appear below the network.
Tel: +49(0) 2154 / 8826‐0
Fax: +49(0) 2154 / 8826‐100
+49 (0)2154 / 8826‐101
Disposal
Do not dispose of this item with normal household waste. Please return any defective
device to your dealer or to a collection point for environmentally sound disposal.
Compliance
Axdia International GmbH hereby declares that this device is in accordance with the
essential requirements and other relevant provisions of Directive 2004/108/EC. The
CE declaration of conformity for this product can be found on the internet at:
www.odys.de – Service – downloads



V2.1.0