Download
Share
Print this page
  1. Manuals
  2. Brands
  3. TOUGH-WORKS Manuals
  4. Sander
  5. MM493B
  6. Instruction manual

TOUGH-WORKS MM493B Instruction Manual

1" x 30" belt and 5" disc sander
Hide thumbs

Advertisement

Quick Links

Download this manual
AND 5" DISC SANDER
IMPORTANT:
For your own safety, read and follow all of the Safety
Guidelines and Operating Instructions before operating
this product.
1" X 30" BELT
MM493B
INSTRUCTION
MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the MM493B and is the answer not in the manual?

Questions and answers

Related Manuals for TOUGH-WORKS MM493B

Summary of Contents for TOUGH-WORKS MM493B

  • Page 1 MM493B 1" X 30" BELT AND 5" DISC SANDER IMPORTANT: INSTRUCTION For your own safety, read and follow all of the Safety Guidelines and Operating Instructions before operating MANUAL this product.
  • Page 2 MM493B BD4603 TABLE OF CONTENTS TABLE OF CONTENTS ....................SPECIFICATIONS ....................... SAFETY GUIDELINES ....................ELECTRICAL SAFETY ....................PACKAGE CONTENTS ....................KEY PARTS DIAGRAN....................A S S E M B L Y / M O U N T I N G ..................

  • Page 3: Tool Operation

    MM493B BD4603 medications that cause drowsiness. WORK AREA PREPARATION For your own safety, read and understand • Keep work area clean. Cluttered work areas all warnings and operating instructions before invite accidents. using any tool or equipment. • Do not use power tools in dangerous en- vironments.
  • Page 4 MM493B the tool is in the “OFF" position before plugging • Know your tool. Learn the tool’s operation, application and specific limitations before using it. • Sander MUST be used with Dust Collector to capture dust. • Disconnect tool when changing belt or abrasive disc.

  • Page 5: Grounding Instructions

    MM493B BD4603 POWER SOURCE Do not permit fingers to touch the terminals of plug when installing or removing from outlet. Do not connect dust collector to the power source • Plug must be plugged into matching outlet until all assembly steps have been completed.

  • Page 6: Extension Cords

    MM493B grounded wire system. off and disconnected from power source while • Many cover plate screws, water pipes and motor is mounted, connected, reconnected outlet boxes are not properly grounded. To or anytime wiring is inspected. ensure proper ground, grounding means must Motor and wires are installed as shown in be tested by a qualified electrician.
  • Page 7 MM493B BD4603 No. Description Qty. Sander Assembly with Abrasive Belt and Disc Sanding Disc Table Miter Gauge Sanding Belt Table Dust Chute (with dust nozzle adapter) Locking Knobs (sanding disc table) Washers (sanding disc table) Washer 8 mm (Sanding Belt Table)
  • Page 8 MM493B Sanding Belt Enclosed Induction Motor Sanding Disc Sanding Belt Table Sanding Disc Table Locking Lever Dust Chute Cast AL Base Switch...

  • Page 9: Belt Table

    MM493B To adjust sanding disc table Place a square on the table with the ruler side Do not use the machine until it is completely against the sanding disc. The table should be assembled and you have read and understood 90°...
  • Page 10 MM493B To set at 45° If needed the table may be tilted. • Loosen the locking lever until it is very loose. • Slide locking lever to the front of the adjusting slot as shown to tilt the table. • Tighten the lock lever.

  • Page 11: Sanding Belt Tracking Adjustment

    MM493B BD4603 secure in place with the belt guard lock knob BACKSTOP and lower guard screws. The backstop is a surface to sand against. To Adjust Belt Wheel Tracking Remove the sanding belt table. See Mount Knob Sanding the Sanding Belt Table paragraph and reverse Belt the order of assembly.
  • Page 12 MM493B BD4603 NOTE: The use of a dust collection system is strongly recommended when using the belt/disc sander. Use of a mask or respirator is still recommended even when using a dust collection system. Dust Port Dust Port Adapter Dust Port...

  • Page 13: Sanding Belt

    MM493B BD4603 on the right side of the sanding disc. Always ON/OFF SWITCH use the left side of the sanding disc; using Refer to Figure P the right side of the sanding disc will cause To turn sander ON place the ON/OFF switch the workpiece to fly up or kickback in the ON position.
  • Page 14 MM493B Make certain that the unit is disconnected from power source before attempting to service or remove any component. CLEANING Keep machine and workshop clean. Do not allow sawdust to accumulate on the tool. Keep the wheels clean. Dirt on the wheels will cause poor tracking and belt slippage.
  • Page 15 MM493B BD4603 PROBLEM PROBLEM CAUSE SUGGESTED CORRECTIVE ACTION 1. Sanding belt/disc has 1. Ensure sanding accessories are Sanding Grains been stored in an incorrect stored away from extremely hot or easily rub off environment. dry temperatures. belt or discs. 2. Sanding belt/disc has 2.
  • Page 16 MM493B BD4603 PROBLEM PROBLEM CAUSE SUGGESTED CORRECTIVE ACTION 1. Sanding belt/disc has 1. Ensure sanding accessories are Sanding Grains been stored in an incorrect stored away from extremely hot or easily rub off environment. dry temperatures. belt or discs. 2. Sanding belt/disc has 2.
  • Page 17 MM493B BD4603...
  • Page 18 MM493B Description Size Q’ty Phillips Screw +Spring Washer M6x18 Rubber Foot Phillips Screw +Flat Washer M4x12 Base Plate Base Switch Plate Phillips Screw M5x10 End Cap Wave Washer 35 Capacitor Toggle with Safety Switch Phillips Screw +Washer+Spring Washer M4x8 Stator...
  • Page 19 MM493B Description Size Q’ty Hex Bolt M10x25 Sanding Belt Support Hex Socket Screw M6x20 Belt Sanding Table Large Flat Washer Ratchet Handle Adjusting Shaft Guard Adjusting Spring Locking Nut Adjusting Fixing Board Adjusting Spring Ⅰ Adjusting Knob Phillips Screw ST4.2x16 Spring Column Pin φ3x20...
  • Page 20 MM493B ONE-YEAR LIMITED WARRANTY Having Problems ? Give us a chance to help you before returning this product Email : info@toolots.com After the phone：(844) 866-5687...