Gude GFO 1401 Instruction Manual

Gude GFO 1401 Instruction Manual

Hide thumbs Also See for GFO 1401:

Advertisement

Quick Links

GFO 1401
English
55174
#
© Copyright Güde GmbH & Co. KG - Birkichstraße 6 - 74549 Wolpertshausen - Germany

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GFO 1401 and is the answer not in the manual?

Questions and answers

Summary of Contents for Gude GFO 1401

  • Page 1 GFO 1401 English 55174 © Copyright Güde GmbH & Co. KG - Birkichstraße 6 - 74549 Wolpertshausen - Germany...
  • Page 2 Kindly read this instruction manual carefully before putting the unit in operation. Reprint, even partial, requires permission. Technical changes reserved. Returns of goods and orders of spare parts will be carried out fast in an expeditious manner by means of an applicable servicing form to be downloaded at: http://www.guede.com/support The form may be also requested at: Tel.:...
  • Page 3 (Abbildungen beispielhaft)
  • Page 4 (Abbildungen beispielhaft)
  • Page 5 That the following Appliance complies with the appropriate basic safety and health requirements of the EC Directive based on its design and type, as brought into circulation by us. In a case of alternation of the machine, not agreed upon by us, this declaration will loose its validity. Machine desciption: Tisch/Kapp/Gehrungssäge GFO 1401 Article-No.: 55174 Date/Authorized Signature: 16.06.09...
  • Page 6 The tool Attention! Table, bevel slide miter saw GFO 1801  Keep the workplace clean and tidy. Disorder on the workplace increases High quality, solid saw for carpenter, bevel danger of an accident and injury. and miter work.  Watch surrounding conditions you are working in.
  • Page 7   To work outdoor use special extension Check the rotation direction of the motor and cables, be sure it is appropriate for this saw blade match together.  purpose and properly marked. Never try to stop rotating saw blade by ...
  • Page 8  If not stated in this instruction manual, all repairs or replacement of damaged parts and safety equipment can be conducted by authorized Service center only.  Damaged switches can be replaced by authorized Service Center.  This tool complies with all corresponding safety instructions.
  • Page 9: Symbols Explanation

    Symbols explanation Technical data: There are used following symbols in this instruction manual and on the tool: Power plug Motor power source Product safety: Revolutins Saw blade This product complies with Tool is provided with protective corresponding standards of EC insulation Restrictions: Noise level...
  • Page 10: Electrical Risks

     Wear respirator while working with the tool. Deviation Connect the dust sucking unit and use it. Faulty setting of the saw blade  Resin Dried resin in the timber Neglecting the ergonomic rules  Workpiece Careless using of personal safety An object which is cut or split.
  • Page 11: Transport And Storage

    Transport and storage Using as bevel or miter saw. (Pict. 9+13+15+16+17+18)  If stored for longer time, it needs to be To use the saw as bevel or miter press the lever cleaned properly.  (pict.9) to unlock the table and then you can tilt it To avoid injuries keep the blade down while over.
  • Page 12: Safety Instructions For Operators

    Linear cuts Safety instructions for operators   Set the parallel ruler towards the saw blade All protective and safety equipment must be to get required width. mounted properly and in place before  Put the workpiece on the table, flat resp. running the tool.
  • Page 13: Safety Instructions For Inspection And Maintenance

     wait 5 to 10 sec. and then turn the tool back Take the saw blade off the spindle and remove on again.  Clean the spindle up and put a new saw blade Overloading reasons  Power cord is too long or has small diameter. Put a new saw blade on and secure it in Secure proper extension cable with minimum opposite way as described above.

Table of Contents