Inhaltsverzeichnis Seite Table des matières Page Beschreibung Description Sicherheitsangaben Indications de sécurité Bedienung Manipulation Ein- und Ausschalten Mise en / hors service Pneumatische Anschlüsse Raccords pneumatiques Betriebsmodi Modes d'exploitation Konfiguration Configuration RS 232 - Betrieb Exploitation RS 232 Batteriewechsel Changement de batterie Kalibration Etalonner Spezifikationen...
Beschreibung Ausschalten OFF - Taste drücken, oder automatische Abschaltung Das THOMMEN Hand-Manometer HM28 ist 1,10 od. 60 Minuten nach ein Digital-Druck-Messinstrument mit einge- letztem Tastendruck. bautem Drucksensor zur Messung von Diffe- Bei Temperaturwechsel muss das Gerät min. renz-, Relativ-, Absolutdruck oder Vacuum.
Page 5
Beispiel Anzeige Hinweise beim Max. Range: Messbereich erscheint Einschalten 200 mbar in der gewählten Einheit Full scale error Genauigkeitsklasse 0.05 % in % v.E. Normal print zero 123.45 mbar nur bei Ausführungen (difference) und hold display ====== oder Differenz- oder analog/hold 123.4 mbar Relativdruck...
Konfiguration Modus wählen: è >2 Sekunden drücken im Display erscheint CONFIGURATION Abspeichern und wieder verlassen: è >2 Sekunden drücken im Display erscheint SAVE CONFIGURATION Beispiel Anzeige Hinweise UNIT set unit mbar, kPa, bar, mbar O, mH mmHg, psi, inH inHg, hPa, Pa, MPa Auflösung der Anzeige, RESOLUTION high...
Page 7
30 min Dämpfung Dämpfung Dämpfung Dämpfung Dämpfung 60 min schaltet das HM28 ein manual - Das HM28 sendet alle 3 s "XON". Um die Baudrate zu bestimmen, in jeder Baudrate Baudrate Baudrate Baudrate Baudrate Übertragungsrate "XON" einlesen, 1200 Baud bis "XON" richtig erkannt wird...
Page 8
Steuerbefehle/Syntax Antwort von HM28/Syntax Beschreibung remote 182 CR (tab)[ok] CR Auf Fernbedienung schalten und Tastatur blockieren local 53 CR (tab)[ok] CR Auf Tastatur umschalten 101 CR (tab)[ok] CR Instrument ausschalten readpress 243 CR (tab)"Wert" _ "Einheit" * Checksum CR Messwert abfragen readpressfast 161 CR (tab)"Wert"...
Page 9
Steuerbefehle/Syntax Antwort von HM28 / Syntax Beschreibung setunit_mmh2o setunit_mmhg setunit_psi setunit_inh2o setunit_inhg setunit_hpa setunit_pa setunit_mpa setbaud_9600 CR (tab)[ok] CR Baudrate wählen (Antwort mit setbaud_4800 neuer Baudrate, vor "XON" >0,1s setbaud_2400 warten) setbaud_1200 resolution_high * 62 CR (tab)[ok] CR Auflösung von Messwert und resolution_low Anzeige wählen, high:10 M/s,...
Alte Batterie sach- und umweltge- recht entsorgen! Kalibration Eine Nachkalibration darf nur von Fach- personal durchgeführt werden. Eine Anleitung ist bei REVUE THOMMEN AG auf Anfrage erhältlich. Wir empfehlen, das Instrument mindestens 1 mal jährlich neu kalibrieren zu lassen. Spezifikationen...
Handpumpe 35 bar SCS-Prüfzertifikat Adapter RS232 9M-25F Wartung NPT 1/8"- Adapter Kommunikationspaket best.aus: Das HM28 ist wartungsfrei. Es kann mit einem - RS232-IF Kabel (9-pol. fem.) feuchten Lappen gereinigt werden. Keine - Kommunikations-Software für lösungsmittelhaltigen Reinigungsmittel ver- MS Windows wenden! - Messstellenverwaltungs- Batteriewechsel und Nachjustieren gemäss...
Connection for RS 232 interface Imperative! Please note warning symbol in the operating instruction. Copyright (c) by REVUE THOMMEN AG. EC Declaration of conformity The contents of this publication may not be copied without the express permission of We declare on our own responsibility that this REVUE THOMMEN AG.
1,10 or 60 min The THOMMEN handheld pressure gauge after the last keystroke. HM28 is a digital pressure measuring In the case of a temperature change the instrument with integrated pressure sensor instrument requires at least 30 minutes to for the measurement of differential, relative or adjust to the new ambient temperature.
Page 15
Display example Notes On switching Max. Range: Measuring range 200 mbar displayed in desired unit Full scale error Accuracy class as a % 0.05 % of full scale reading Normal print zero 123.45 mbar Only with differential (differential) hold display ====== oder or relative pressure 123.4 mbar...
Configuration Select mode: è Press >2 seconds in the Displayappears CONFIGURATION Store and then exit: è Press >2 seconds in the Display appears SAVE CONFIGURATION Display example Notes set unit mbar, kPa, bar, UNIT O, mH mbar mmHg, psi, inH inHg, hPa, Pa, MPa RESOLUTION Display resolution,...
The string |||| ||**----------- Cut-out time must be terminated with a CR |||| |*------------- Time unit - A "TAB" is prefixed to each checkback |***-*-------------- Storage interv *------------------- Display rate signal of the HM28, a "*" suffixed and the...
Page 18
Control commands/syntax Answer from HM28/syntax Description remote 182 CR (tab)[ok] CR Switch to remote control and block keypad local 53 CR (tab)[ok] CR Switch to keypad 101 CR (tab)[ok] CR Switch off instrument readpress 243 CR (tab)"Value" _ "Unit" * Checksum...
Page 19
Control commands/syntax Answer from HM28/syntax Description setunit_mmh2o setunit_mmhg setunit_psi setunit_inh2o setunit_inhg setunit_hpa setunit_pa setunit_mpa setbaud_9600 CR (tab)[ok] CR Select baud rate (answer with setbaud_4800 new baud rate, wait >0,1s setbaud_2400 before "XON") setbaud_1200 resolution_high * 62 CR (tab)[ok] CR Select measured value resolution...
Calibration Recalibration is only to be carried out by specialist staff. Relevant instructions are obtainable from REVUE THOMMEN AG on request. We recommend that you have the instrument recalibrated at least once per year. Specifications Technical data...
Mains supply unit connection Accessories The HM28 can be operated from a regulated Standard 1 9 V block battery plug-in mains supply unit. 1 operating instructions Input 230 V, 50 Hz Option Plug-in mains supply unit Output 9 V DC ± 20 %, 100 mA...
Description Mise hors service Pressez touche OFF, ou arrêt automatique après 1, 10 ou 60 minutes Le manomètre portatif THOMMEN HM28 est après dernière action un instrument digital de mesure de pression sur une touche. avec capteur intégré pour la mesure de Après un changement de température,...
Page 25
Indications Exemple d’affichage Champ de mesure Lors de la mise Max. Range: apparaît dans l'unité en marche 200 mbar sélectionnée Classe de pécision en % Full scale error p.é. 0.05 % Normal print zero 123.45 mbar Seulement pour (difference) et hold display ====== oder...
Page 26
Configuration Sélectionnez le mode: è Pressez touche MODE >2 secondes CONFIGURATION apparaît sur l’afficheur Mémorisez et quittez de nouveau: è Pressez touche MODE >2 secondes SAVE CONFIGURATION apparaît sur l’afficheur Exemple Indications d’affichage set unit mbar, kPa, bar, UNIT O, mH mbar mmHg, psi, inH inHg, hPa, Pa, MPa...
Pa(25mbar-7bar) unité de temps unité de temps unité de temps raccordant le courant d'alimentation /hours - HM28 émet toutes les 3 s "XON". Afin de /minutes déterminer la fréquence baud, lire "XON" mH2O(70bar seul, intervalle de intervalle de intervalle de...
Page 28
Ordres de commande/Syntax Réponse de HM28/Syntax Description remote 182 CR (tab)[ok] CR Commutez sur commande à distance et verrouillez le clavier local 53 CR (tab)[ok] CR Commutez sur clavier 101 CR (tab)[ok] CR Mise à l'arrêt de l'instrument readpress 243 CR (tab)"Valeur"...
Page 29
Ordres de commande/Syntax Réponse de HM28/Syntax Description setunit_mmh2o setunit_mmhg setunit_psi setunit_inh2o setunit_inhg setunit_hpa setunit_pa setunit_mpa setbaud_9600 (tab)[ok] CR Sélectionnez Baudrate (réponse setbaud_4800 avec nouveau Baudrate, avant setbaud_2400 "XON" attendre >0,1s) setbaud_1200 resolution_high * 62 CR (tab)[ok] CR Sélectionnez résolution pour...
Etalonnage Un étalonnage ultérieur ne doit être effectué que par un personnel qualifié. Des instructions relatives sont disponibles sur demande chez REVUE THOMMEN SA. Nous recommandons de refaire étalonner l'instrument au moins une fois par an. Spécifications Caractéristiques techniques...
Raccord pour unité d'alimentation Accessoires réseau Standard 1 batterie-bloc 9 V L'instrument HM28 peut être exploité à l'aide 1 mode d'emploi d'une unité d'alimentation secteur stabilisée. En option Unité d'alimentation secteur avec fiche 230V, 50 Hz Entrée 230 V, 50 Hz...
Page 34
Spegnimento: premere il tasto OFF. Lo Descrizione spegnimento automatico può essere predisposto in Il manometro palmare THOMMEN HM28 è un tempo compreso tra 1,10 uno strumento digitale portatile dotato di un e 60 minuti dopoche l’ultimo sensore per le misure di pressione tasto sia stato premuto.
Page 35
Esempio di indicazione Note Accensione Max. Range: Campo di misura 200 mbar visualizzato nell'unita prescelta Full scale error Classe di precisione in 0.05 % % del fondo scala zero 123.45 mbar Solo nei modelli per le Normale print display ====== oder pressioni differenziali (differenziali) e hold...
Page 36
Configurazione Per selezionare la modalità operativa: è premere il tasto MODE per più di 2 secondo; nel display compare CONFIGURATION memorizzare ed uscire: è premere il tasto MODE per più di 2 secondo; nel display compare SAVE CONFIGURATION Esempio di Note indicazione UNIT...
Page 37
Unità di tempo Unità di tempo Unità di tempo Unità di tempo tensione di alimentazione /hours - L’HM28 invia ”XON ” ogni 5 secondi. Per mH2O(con 70bar, /minutes determinare il baudrate, leggere ”XON” in altimentri mmH2O) Intervallo di Intervallo di...
Page 38
Comandi di controllo/sintassi Risposta dall’HM28/sintassi Descrizione remote 182 CR (tab)[ok] CR Commutare sul controllo, da PC, e bloccare la tastiera dell'HM28 local 53 CR (tab)[ok] CR Commutare sulla tastiera 101 CR (tab)[ok] CR Spegnere lo strumento readpress 243 CR (tab)"Valore"...
Page 39
Comandi di controllo/sintassi Risposta dall’HM28/sintassi Descrizione setunit_mmh2o setunit_mmhg setunit_psi setunit_inh2o setunit_inhg setunit_hpa setunit_pa setunit_mpa setbaud_9600 CR (tab)[ok] CR Selezionare il baudrate (rispondere setbaud_4800 con un nuovo baudrate,attendere setbaud_2400 per un tempo superiore a 0,1 s setbaud_1200 prima del "XON") resolution_high *...
Calibrazione La ricalibrazione va affidata esclusiva- mente a personale specializzato. La REVUE THOMMEN AG fornisce a richiesta le istruzioni necessarie. Consigliamo di far calibrare lo strumento almeno 1 volta all'anno. Specifiche Caratteristiche tecniche...
Collegamento per alimentazione Accessori da rete Standard 1 batteria 9V L’HM28 può essere alimentato dalla rete con 1 istruzioni per l’uso un alimentatore regolato A richiesta Alimentatore da rete a spina Ingresso 230V, 50Hz 230 V, 50 Hz Uscita 9 V DC ± 20 %, 100 mA Custodia in pelle con cinghia a (min.
Page 43
REVUE THOMMEN AG 4437 Waldenburg Switzerland Phone +41 61 965 22 22 +41 61 961 81 71 www.thommenag.ch Made in Switzerland...
Need help?
Do you have a question about the HM28 and is the answer not in the manual?
Questions and answers