Page 2
The product information, specifications, and technical data embodied in this manual represent the technical status at the time of writing and are subject to change without prior notice. Windows is a registered trademark of Microsoft Corporation. OMICRON Lab and Smart Measurement Solutions are registered trademarks of OMICRON electronics.
Getting started ......................... 12 System requirements ......................12 Installing the Bode Analyzer Suite ..................12 Powering the Bode 100 ...................... 12 Connecting Bode 100 to a computer ................. 13 Performing your first measurement ................... 13 Troubleshooting ......................16 Support ..........................17 Index ...........................
This Bode 100 Quick Start Guide provides you short information on how to install the Bode Analyzer Suite and how to connect Bode 100 to your PC . It is intended as an aid for you to take Bode 100 into operation quickly and easily. Thus, this Quick Start Guide only provides a small subset of information available for Bode 100.
Use Bode 100 in observance of all existing safety requirements from national standards for accident prevention and environmental protection. Reading the Bode 100 manual alone does not release you from the duty of complying with all national and international safety regulations relevant for working with Bode 100, for example, the regulation EN50191 "Erection and Operation of Electrical Test Equipment”.
• Always keep the manual either printed or as PDF file at the site where Bode 100 is used. The manual must be read by all people working with Bode 100. In addition to the manual and the applicable regulations for accident prevention in the country and at the site of operation, heed the accepted technical procedures for safe and competent work.
A est conforme à la norme NMB-003 du Canada. Information for disposal and recycling Bode 100 and all of its accessories are not intended for household use. At the end of its service life, do not dispose of the test set with household waste! For customers in EU countries (incl.
BNC adapters (straight, T, Short, Bode 100 Quick Start Guide Multilingual safety instructions Load 50 Ω) The delivered items may vary a bit from the look shown above. Please refer to the packing list received with the Bode 100 for further information OMICRON Lab...
Order number: OL000169 PML-111O 10:1 Passive Probe PML-111O is a passive 10:1 probe designed for the input stage of Bode 100. It is manufactured by PMK in Germany and fits perfectly to the Bode 100. Order number: OL000110 B-SMC Impedance Adapter for surface mount components The B-SMC extends the impedance measurement range of Bode 100.
Page 10
The B-RFID adapters allow standard compliant measurement of the resonance frequency and Q-factor of RFID antennas. Order numbers: OL000170-OL000173 For more information on the above mentioned Bode 100 accessories and recommended accessories manufactured by partner companies visit www.omicron-lab.com. OMICRON Lab...
• INPUT CH 2 (channel 2 input), Type: BNC jack Further on a green LED is lit at the front panel when the Bode 100 is powered. Figure 5-1: Bode 100 front view Bode 100 provides the following connectors at the back panel: •...
Bode 100 is powered with an external wide-range AC power adapter. Before powering Bode 100, select the adapter’s mains input plug fitting your power outlet. Plug the adapter’s DC output connector into the Bode 100 DC power input on the rear panel and the mains input plug into the power outlet. OMICRON Lab...
Follow the steps described below to perform your first measurement: Connect the test object "IF Filter" to Bode 100 with two BNC cables as shown in the figure below. Figure 6-1: Connecting the test object IF Filter to Bode 100...
Page 14
Figure 6-2: Bode Analyzer Suite start screen To find out if your Bode 100 is recognized by the Bode Analyzer Suite, check if the serial number of your Bode 100 is displayed like shown in the figure above (see 1.). If no serial number is displayed,...
Page 15
(S11) of the IF filter. Please refer to the Bode 100 User Manual for more information on the Bode 100 and its measurement capabilities. You can view the user manual by clicking Read user manual in the start screen or by clicking the help icon that is available at the top right corner of the Bode Analyzer Suite window.
Check if the USB cable is properly plugged into the computer and the Bode 100. b. Try disconnecting and re-connecting the USB cable. c. If this does not help, avoid USB hubs and plug Bode 100 directly into an USB port of your computer.
Asia-Pacific: +852 3767 5500 Europe / Middle East / Africa: +43 59495 Additionally, you can find the OMICRON Lab Service Center or Sales Partner closest to you at www.omicron-lab.com → Contact. OMICRON Lab OMICRON electronics GmbH, Oberes Ried 1, 6833 Klaus, Austria. +43 59495.
Page 19
Index Technical support ........17 Troubleshooting Check power ......... 16 Check USB connection ...... 16 Search and reconnect ...... 16 Troubleshooting .......... 16 User Manual ..........13 Web (OMICRON Lab website) ....17 OMICRON Lab...