Table of Contents
Related Manuals for Henkovac T2
Summary of Contents for Henkovac T2
- Page 1 User Manual Vacuum Packaging Machines T2, T3, T4, T5, T6 M1, M2, M3 M4, M5, M6 M7, M8 D1, D3, D4 http: //www.henkovac.com e-mail: info@henkovac.com tel: +31736271201 SERIAL NUMBER art.nr. 9606.041EN 1ST CHOICE FOR PROFESSIONALS WORLDWIDE...
-
Page 2: Safety Regulations And Warnings
Consequently, we reserve the right to make changes to this document without prior notification. This document is applicable to the indicated models of the Henkovac packaging machine in the version supplied. The manufacturer therefore does not accept any liability for any form of damage or injury resulting from deviating from the specifications of these machines as supplied to you. -
Page 3: Table Of Contents
Safety Regulations and Warnings Table of Contents 3.0. Welcome Service from your Dealer YouTube Henkovac Channel - Instruction and Service Videos General Precaution Installation of Machine Gas Connection for MAP Applications Compressed Air Connection for Additional Sealing Pressure Overview of Main Machine Components... - Page 4 Struts, Dampers and Springs 11.8 Vacuum Hoses and Tubes 12.0 Malfunctions and Notifications 12.1 Service and Technical Support 12.2 YouTube Henkovac Channel - Instruction and Service Videos 12.3 Trouble Shooting Check List 13.0 Recommended Spare Parts 14.0 Utilities 14.1 General data 15.0...
-
Page 5: Welcome
Welcome Thank you very much for your purchase of a Henkovac vacuum packaging machine. In order to guaran- tee the reliability, longevity and robustness of your equipment, we only used materials of the highest quality in the fabrication of your machine. During its design, it was our goal to make it easy to use and simple to maintain. -
Page 6: Installation Of Machine
Extra sealing pressure is not necessary and not available for the Table-Top, M1, M2, M3 Consult your dealer for installation details Maximum pressure: 1 bar Assure a good connection and use high-quality mater Page 6 of 32 Users Manual Henkovac 04-serie V2019... -
Page 7: Overview Of Main Machine Components
Compressed air connection (ex- Fitting plates (optional) tra sealing pressure option) Exhaust (located in the cover on double-chamber Wheel with lock and some mobile models) Cover lock (not for dou- ble-chamber machines) Users Manual Henkovac 04-serie V2019 Page 7 of 32... -
Page 8: Digital Control With Lcd Display
Digital Control with LCD Display Some Henkovac vacuum machines have a control system with just one Program (P1). Other machines have an optional expanded control system, which can accommodate up to 9 custom programs (P1-9). 6.1 One-Program Control System Henkovac machines with the One-Program control system can be programmed for the following 2 functions: 1. -
Page 9: Operating The Machine With One-Program Control System
These additional cycles allow any moisture in the oil of the pump to evaporate. This in- creases the longevity of the machine and minimizes the need for oil changes and pump maintenance Users Manual Henkovac 04-serie V2019 Page 9 of 32... -
Page 10: Ten-Program Control System
6.3 Ten-Program Control System In addition to vacuum and sealing times, Henkovac machines with a Ten-Program control system may be programmed for several additional functions. Each of the 9 customizable programs is either 1. time-controlled 2. -
Page 11: Operating The Machine With Ten-Program Control System
3. Turns functions ON/OFF; specific functions, like soft-air, clean cut seal, etc., are turned either on or off 4. If the function is turned on, the value may be adjusted by pressing the buttons Users Manual Henkovac 04-serie V2019 Page 11 of 32... - Page 12 Except for regularly changing the oil in the pump, the machine requires little other routine maintenance o After reaching the service limit, the display will indicate the negative number of ex- ceeded operating hours or cycles Page 12 of 32 Users Manual Henkovac 04-serie V2019...
-
Page 13: Programming The Machine
7.0 Programming the Machine 7.1 One-Program Control System The One-Program control system is standard on the T2, T3, T4, T5, M1, M3 (with 21m pump) The One-Program control system is time-based ... -
Page 14: Turning Off Machine
(only with sensor) Clean Cut Controlled (CCC) Seal: on/off, in seconds Soft-Air: on/off, in seconds or mbar (only with sensor) Multi-cycle: on/off, in number of cycles Page 14 of 32 Users Manual Henkovac 04-serie V2019... -
Page 15: Reviewing Function Values For
Home menu 7.2.6 Turning Off Machine Follow the same procedure as for the One-Program control system, as explained on page 14 Users Manual Henkovac 04-serie V2019 Page 15 of 32... -
Page 16: Symbols In Display
Programmable in the Settings menu Page 16 of 32 Users Manual Henkovac 04-serie V2019... - Page 17 The objective of this procedure is to minimize the amount of oxygen remaining in the package The number of cycles is counted down in the display Users Manual Henkovac 04-serie V2019 Page 17 of 32...
-
Page 18: Standard Vacuum Pump Settings: Runs Continuously Or Turns Off End Of Cycle
D1, D3, D4 en D6, runs continuously. After completion of a packing cy- cle, the pump will stop after 15 minutes of inactivity. The pump of table units T2, T3, T4 and T5 starts when the cover is closed; the pump stops when the cover is opened again. ... -
Page 19: Explanation Terminology Used
Can be turned on or off in the Settings menu After reaching a programmed vacuum pressure, the package is filled with an inert gas, such as CO2, nitrogen, oxygen, or a mixture thereof. This feature is either time or pressure-controlled. Users Manual Henkovac 04-serie V2019 Page 19 of 32... -
Page 20: Sealing
& two-sided seal clean cut controlled Single Seal Only for T2. The package is sealed with a single sealing wire Double Seal All other machines are equipped with a double sealing wire Clean Cut Seal (CC Seal) One of the two heated wires is used to score the package. -
Page 21: Soft-Air
The pump will continue to run for some time, before turning off automatically. This allows any moisture in the oil of the pump to evaporate Users Manual Henkovac 04-serie V2019 Page 21 of 32... -
Page 22: Maintenance
Regular maintenance prevents equipment malfunctions and prolongs the life of the machine. In addition, it optimizes sanitary conditions. Always have a certified Henkovac dealer carry out repair and maintenance activities Warning During maintenance activities, always turn the machine off at the main switch and/or unplug it... -
Page 23: Pump Oil, Add Or Replace
Note Collect the oil to have it processed and recycled according to the locally applicable regulations Users Manual Henkovac 04-serie V2019 Page 23 of 32... -
Page 24: Seal Beams And Counter Beams
2. Replace the Teflon tape on the seal beam if damaged and replace the sealing wire if kinked 3. Replace the silicone rubber seal if it is burned in Depending on the type of machine, there are three seal beam versions: 1. Single-seal beam (T2) 2. Stainless steel seal beam 3. Aluminum seal beam 11.4.1 Single-Seal Beam... -
Page 25: Aluminum/Stainless Steel Seal Beam
5. Apply the Teflon tape smooth and tight over the seal beam without creases Make sure that the beam is clean and free of grease 6. Re-install the seal beam in the vacuum chamber and re-connect the wires Users Manual Henkovac 04-serie V2019 Page 25 of 32... -
Page 26: Aluminum T-Shaped Seal Beam
6. Slide the seal beam in the holder of the cover, tighten the mounting screws, and re-connect the wires (machines with metal cover) Note The Teflon tape must not adhere to the tension blocks (E) Page 26 of 32 Users Manual Henkovac 04-serie V2019... -
Page 27: Replacing Silicone Rubber Seal Of Counter Beam
Have the gas struts replaced if the lid no longer opens properly 11.8 Vacuum Hoses and Tubes Check the vacuum hoses and tubes for kinks, tears and porosity; replace if necessary Users Manual Henkovac 04-serie V2019 Page 27 of 32... -
Page 28: Malfunctions And Notifications
If technical support is required, please contact your dealer You may also contact us, so that we can assist you in locating your nearest dealer +31 73 627 12 73 of 77 or by e-mail info@henkovac.com. 12.1 Service and Technical Support Please have the following information available: ... -
Page 29: Recommended Spare Parts
Oil ISO VG32 (1 Ltr) 03.01.1.0120 Oil ISO VG100 (1 Ltr) 0301.00000 Oil ISO VG100 (1 Ltr) PRIVATE Miscellaneous 9705.00035 Seal 8mm for transparent lid (Length 5mtr) 0504.00045 Silicone profile for stainless steel cover Users Manual Henkovac 04-serie V2019 Page 29 of 32... -
Page 30: Utilities
Connecting the compressed air WARNING Risk for electric shock; before opening, remove the plug from the outlet Access by certified personnel only Connection for compressed air Connection for MAP gas Page 30 of 32 Users Manual Henkovac 04-serie V2019... -
Page 31: Ce Declaration Of Conformity
La conformité est demonstrée par la conformité intégrale avec les normes suivantes: La conformità è dimostrata dalla conformità alle sequenti norme: NEN-EN-ISO 12100-1 NEN-EN-ISO 12100-2 NEN-EN-ISO 14121-1 NEN-EN-ISO 13857 NEN-EN-ISO 60204-1 E.H. Goudsmid Managing Director The Netherlands, 's-Hertogenbosch, Januari 2014 Users Manual Henkovac 04-serie V2019 Page 31 of 32... - Page 32 Phone: +31 (0)73 6 271 271 e-mail: info@henkovac.com Henkovac International B.V. Het Sterrenbeeld 36 5215 ML `s Hertogenbosch The Netherlands P.O. Box 2261 5202 CG `s Hertogenbosch The Netherlands...
Need help?
Do you have a question about the T2 and is the answer not in the manual?
Questions and answers