Advertisement
DO NOT touch the workpiece immediately after grinding as it will be very hot.
DO NOT try to cool the grinding stones with water or other lubricants.
DO NOT hold unsecured work in your hand. DO NOT touch the grinding stone whilst operating or whilst connected to the mains
DO NOT leave the grinder running unattended.
DO NOT operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use switch grinder off, remove plug from power supply.
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition.
DO NOT use the grinder where there are flammable liquids, solids or gases.
DO NOT allow grinder sparks to make contact with the operator's clothing or any other fabric such as cleaning rags. Fabrics contaminated with
flammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in preference to
man-made fibres.
2. INTRODUCTION
Fitted with induction motor suitable for workshop use. Ø200mm Sharpening wet stone with adjustable flow rate water bath and drain outlet.
Features an angle adjustable tool rest to suit work piece. Additional tool clamp can be used which includes protractor gauge for extra angle.
Ø125mm Dry stone with eye shield guard and fixed tool rest. Ideal for sharpening tools, knives etc.
3.
SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMS2107
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250W - 230V
Dry Stone Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2850rpm
Wet Stone Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .320rpm
Dry Stone Size:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø125 x 50mm
Wet Stone Size:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø200 x 25mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.7kg
4.
ASSEMBLY
WARNING! Before assembly check to ensure grinder is unplugged from mains.
4.1.
EYESHIELD (fig.1.7)
Adjust the eyeshield so that the perspex provides maximum protection against debris being thrown from the wheel.
4.1.1. The eyeshield is adjusted by slackening the clamp bolt (fig.5), moving the eyeshield support arm and tightening the clamp bolt when
correctly situated.
4.2.
TOOL REST (fig.1.6/1.8)
4.2.1. Tool rest should be adjusted to provide no more than a 2mm gap between the wheel and rest.
4.2.2. Turn the dry wheel by hand to check that this distance remains true for the complete rotation.
4.3.
WATER RESERVOIR (fig.1.4)
4.3.1. Fit the centre stem of the reservoir in the location attached to the wet stone housing; the outlet from the flow regulator (fig.1.5) should
fall onto the wet stone.
4.3.2. Fit the drain tube to the spigot (fig.6) and place the end of the tube in a suitable container to catch the waste water.
4.4.
Install the grinder by mounting on a fireproof bench. Use the mounting holes as a template for drilling through the bench.
4.5.
Check that all fastenings are tight and then read section 5 (Grinding stones) before use.
5.
GRINDING STONES
5.1.
MANDATORY SAFETY INSTRUCTIONS (The following instructions must be observed together with section 1 safety).
DANGER! Use of a damaged stone is dangerous and may cause damage and/or personal injury.
WARNING! Ensure grinder is isolated from the mains supply before attempting to change grinding stones(or Wheel).
Only persons qualified under the "Abrasive Wheels Regulations" and holding a current grinding wheel certificate are
authorised to change and dress grinding stones (wheels).
Grinding stones (wheels) used with this machine must be of an adequate speed rating and suitable for the material to be ground.
Ensure the grinding stone's maximum speed specification is higher than that indicated on the machine data plate.
Check grinding stone is secure, the stone is not worn or damaged and that there are no splits or cracks. If damaged replace
immediately.
Ensure replacement stone is not damaged in any way such as cracks, deformations or splinters etc. Also check the mounting flanges
to ensure they are not deformed, burred or chipped. Damaged items must NOT be used as they may cause irregular pressure on the
stone which may cause a stone to break.
© Jack Sealey Limited
DANGER OF FIRE/EXPLOSION HAZARD
Key:
1 . . . . . . . . On/Off switch
2 . . . . . . . . Dry Stone
3 . . . . . . . . Wet Stone
4 . . . . . . . . Water Reservoir
5 . . . . . . . . Flow Regulator
6 . . . . . . . . Dry Stone Tool Rest
7 . . . . . . . . Eyeshield
8 . . . . . . . . Wet Stone Tool Rest
9 . . . . . . . . Tool Holder
10 . . . . . . . Tool Rest Vertical Angle Adjuster
11 . . . . . . . Tool Rest Horizontal Angle Adjuster
12 . . . . . . . Tool Rest Height Adjuster
fig.1
Original Language Version
SMS2107 Issue: 1 - 07/01/15
Advertisement
