Symetrix xIO Stage 4x4 Quick Start Manual

QUICK START GUIDE:
What's In The Box?
• A xIO Stage 4x4.
• A Printed Quick Start Guide.
• Four #10-32 x 3/8" Black Phillips Screws.
• Four #10 Black Rubber Washers.
• Two Male XLR Dummy Plugs.
• Two Female XLR Dummy Plugs.
• Six 5.6" Black Cable Ties.

What You Need to Provide

A Windows PC with 1 GHz or higher
processor and:
• Windows 7 ® or higher.
• 250 MB free storage space.
• 1024x768 graphics capability.
• 16-bit or higher colors.
• Internet connection.
• 512 MB or more of RAM as required by
your operating system.
• A Symetrix Radius NX, Prism, or Edge
hardware device.
• CAT5/6 cable or an existing Dante network.
• Standard 8"x8"x4" electrical enclosure.
• 802.3af Class 0 PoE switch or injector, 10
Watts minimium.

Getting Help

Composer, the Windows software that
configures xIO Stage 4x4 hardware, includes
a help module which acts as a complete
User's Guide for both hardware and software.
If you have questions beyond the scope of
this Quick Start Guide, contact our Customer
Support Group in the following ways:
Tel: +1.425.778.7728
6:00 am to 6:00 pm
Monday through Friday,
Pacific Time
Web: http://www.symetrix.co
Email: support@symetrix.co
Chat: http://symetrix.casengo.com/vip/
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a commercial installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment under FCC rules.
Cet appariel numerique de la classe A respecte toutes les Exigences du
Reglement sur le materiel brouilleur du Canada.
www.symetrix.co | +1.425.778.7728
xIO Stage 4x4

Important Safety Instructions

1.
Read these instructions.
2.
Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water. This
apparatus shall not be exposed to dripping
or splashing and no objects filled with
liquids, such as vases, shall be placed on
the apparatus.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install only in accordance with the
manufacturer's instructions.
8.
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
9.
Ensure proper ESD control and grounding,
particularly around exposed I/O terminals.
The xIO Stage 4x4 is provided with a
chassis grounding wire for attaching to
typical, metal, junction box enclosures.
Follow local codes for bonding these to
earth ground. This is required for safety, but
also greatly improves ESD resilience.
10. Protect cords from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
1 of 4
12. Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF FIRE OR
WARNING:
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE
AVIS:
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
SEE OWNERS MANUAL. VOIR CAHIER D'INSTRUCTIONS.
No user serviceable parts inside. Refer servicing to qualified service personnel.
Il ne se trouve a l'interieur aucune piece pourvant entre reparée l'usager.
S'adresser a un reparateur compétent.
•
The lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user of the presence
of uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons. The exclamation
point within an equilateral triangle is
intended to alert the user of the presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the product (i.e. this Quick
Start Guide).
•
CAUTION: To prevent electric shock, do
not use polarized plugs with any extension
cord, receptacle or other outlet unless the
prongs can be fully inserted.
•
User Serviceable Parts: There are no
user serviceable parts inside this Symetrix
product. In case of failure, customers
inside the U.S. should refer all servicing to
the Symetrix factory. Customers outside
the U.S. should refer all servicing to an
authorized Symetrix distributor. Distributor
contact information is available online at:
http://www.symetrix.co.