Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Agreto Swis721 LT BT Standart
Summary of Contents for Agreto Swis721 LT BT Standart
- Page 1 User Manual AGRETO Animal Scale 23.1.2019...
-
Page 2: Table Of Contents
Mounting the door operating rod .................. 14 6.10 Mounting the display bracket ..................15 6.11 Mounting the weighing display .................. 16 6.12 Connecting the cabling ..................... 16 Troubleshooting ....................18 Warranty ......................19 Disposal ......................20 Legal Notice......................20 © AGRETO electronics GmbH Seite:2... -
Page 3: Introduction
3 Intended use The AGRETO Animal Scale is designed for the weighing of pigs, sheep and other animals up to 300 kg, so long as the size of the scale is sufficient. The scale is compliant with protection class IP68, and the AGRETO HD1 weighing display with protection class IP67. -
Page 4: Safety
4 Safety 4.1 Safety instructions for the buyer IMPORTANT! Ensure that anyone using the AGRETO Single Animal Weighing Scale for the first time has read and understood this manual. 4.2 Safety instructions for assembly personnel Appropriate means must be used when transporting machine parts with load-bearing devices. -
Page 5: Safety Instructions For Machine Operators
Risk of tripping on components/tools that may lie in the vicinity. 4.3 Safety instructions for machine operators HAZARD! The AGRETO Single Animal Weighing Scale may only be operated by persons who are familiar with the handling of the appliance. CAUTION! Keep the word area clean. -
Page 6: Technical Specifications
120 %, breaking load 150 % accuracy: +/- 0.02 % waterproof in accordance with protection class IP68 operating temperature: -35 to +65 degrees Celsius temperature compensation: -10 to +40 degrees Celsius © AGRETO electronics GmbH Seite:6... -
Page 7: Assembly Of Scale
The handles must point outwards. The side with the wheels is referred to as "front" in this manual, the side with the handles as "rear". The directions left and right are seen from the handle side. Then place the balance on the floor with the feet. © AGRETO electronics GmbH Seite:7... -
Page 8: Mounting Of Side Panels
Place the upper side panels also with the smooth surface facing inwards, while paying attention to the cables. Secure the panels with two screws each at the front and back, too. Don't tighten the screws yet. © AGRETO electronics GmbH Seite:8... -
Page 9: Screwing Together The Side Panels
Pay attention to the cables. Screw the side panels to the floor panel. In case of the middle 3 screws, one reinforcement angle is screwed and no second washer is used. Now tighten all screws. © AGRETO electronics GmbH Seite:9... -
Page 10: Mounting The Doors
The front door is usually remote controlled, and kept closed due to the construction of the remote control. The bolt can here also be fixed in the open position. © AGRETO electronics GmbH Seite:10... -
Page 11: Mounting The Wheels
The wheels have a mounted inner socket, and the screws can therefore be tightened. 6.7 Mounting the castor required mounting material size pieces fillister head screw M10x50 washer stop nut Mount the castor at the front door, as shown. © AGRETO electronics GmbH Seite:11... -
Page 12: Mounting The Door Lever
The standing component must point inward. Attach the lever to the outside of the mounting bracket. The short part of the lever must face inward. The rounded head screw must point from inside to outside. © AGRETO electronics GmbH Seite:12... - Page 13 AGRETO Animal Scale Mount the ball outside on the lever. Attach the rubber buffer on the left-hand side panel, as shown. © AGRETO electronics GmbH Seite:13...
-
Page 14: Mounting The Door Operating Rod
If necessary, you can slightly remove one of the ball joints from the bar. © AGRETO electronics GmbH Seite:14... -
Page 15: Mounting The Display Bracket
Attach the mounting bracket for the display as shown. In the normal state the holding bracket protrudes outwards and can be folded inwards. Tighten the stop nuts only enough to ensure that the bracket can be turned. © AGRETO electronics GmbH Seite:15... -
Page 16: Mounting The Weighing Display
Thread the weighing signal cable of the indicator through the screw connection and down through the mounting bracket and connect it to the distributor. Attach the other two weighing signals to the distributor too. © AGRETO electronics GmbH Seite:16... - Page 17 Thread one cable connector each through the latch of the self-adhesive cable brackets. Glue the brackets to the underside of the side panel and attach the cables. Use the additional cable connectors to attach the cables and the distributor. © AGRETO electronics GmbH Seite:17...
-
Page 18: Troubleshooting
In the case of damage to a cable, the affected cable, including the loadcell, must be replaced. If all of the above are excluded, please contact the manufacturer. © AGRETO electronics GmbH Seite:18... -
Page 19: Warranty
8 Warranty In addition to the statutory warranty, the following warranty provisions apply to the AGRETO animal scale: AGRETO electronics GmbH guarantees the function of and shall repair or replace all parts which show material or manufacturing damage within the warranty period. -
Page 20: Disposal
All information, specifications and illustrations are based on the product state as of 2019, subject to technical changes or design modifications. All information contained in this manual is given without any guarantee. The liability of the author is excluded. Copyright © 2019, AGRETO electronics GmbH AGRETO electronics GmbH Pommersdorf 11 A-3820 Raabs Tel.: +43 2846 620 0...
Need help?
Do you have a question about the Swis721 LT BT Standart and is the answer not in the manual?
Questions and answers