Advertisement
GEOVANE
Wind direction measurements reinvented
INSTRUCTIONS
Use the following input channels on the logger to connect this sensor. See highligted input channels marked here below. The
wire colors used in the connection diagram below only applies in case the cable is supplied by Kintech Engineering.
Depending on the number of pins to be used, the number of necessary wires can range from three (frequency output) to eight.
See section 3.2 of the manual for detailed pinout and section 8 of the manual for how to configure.
GSM
BAT
BAT
5V
5V
5V
1
1
1
SIG
SIG
SIG
SIG
SIG
SIG
SIG
SIG
DIR 1
DIR 1
DIR 1
DIR 1
DIR 2
DIR 2
DIR 2
DIR 2
SENSOR PIN DESCRIPTION
Avda. Anselmo Clavé nº 37-45 - 50004, Zaragoza - Spain
Tel. (+34) 976 221 789
support@kintech-engineering.com
www.geovane360.com / www.kintech-engineering.com
ANEMOMETER INPUTS
ANEMOMETER INPUTS
ANEMOMETER INPUTS
5V
5V
5V
2
2
2
3
3
3
4
4
4
5
5
5
6
6
6
7
7
7
2 5
2 5
2 5
1
1
2
2
3
3
4
4
5
5
1
2
3
4
5
ANALOG INPUTS
ANALOG INPUTS
ANALOG INPUTS
1 Out (V1+)
2 RS-485 A
3 Supply (+)
4 RS-485 B
5 Out (V2+)
6 Out (Hz)
7 Supply (-)
8 Out (-)
-
Shield
OUT
OUT
OUT
OUT
5V
5V
5V
8
8
8
9
9
9
10
10
10
3
3
3
3
2
2
2
2
1
1
1
1
1
1
2
2
3
3
4
4
5
5
6
6
7
7
1
2
3
4
5
6
7
EXTRA ANALOG INPUTS
EXTRA ANALOG INPUTS
EXTRA ANALOG INPUTS
DATA LOGGER INPUT CHANNEL
Analog Inputs
BAT
Analog Inputs
Anemometer Inputs
BAT
Analog Inputs
BAT
GPS
DIGITAL INPUT 1
DIGITAL INPUT 1
DIGITAL INPUT 1
DIGITAL INPUT 1
8
8
8
8
7
7
7
7
6
6
6
6
5
5
5
5
4
4
4
4
3
3
3
3
2
2
2
2
8
8
8
8
7
7
6
6
5
5
4
4
3
3
2
2
8
8
8
7
7
6
6
5
5
4
4
3
3
2
2
DIGITAL INPUT 2
DIGITAL INPUT 2
DIGITAL INPUT 2
DIGITAL INPUT 2
1
(+)
2
1
(-)
(-)
GND
1
1
1
1
1
1
1
1
Advertisement
Table of Contents
Related Manuals for Kintech Engineering Geovane
Summary of Contents for Kintech Engineering Geovane
- Page 1 Use the following input channels on the logger to connect this sensor. See highligted input channels marked here below. The wire colors used in the connection diagram below only applies in case the cable is supplied by Kintech Engineering. Depending on the number of pins to be used, the number of necessary wires can range from three (frequency output) to eight.
- Page 2 HOW TO CONFIGURE THIS SENSOR IN EOL MANAGER Keep in mind that the configuration of a Geovane in EOL Manager has to be done according to its outputs configuration. Open EOL Manager and go to the data logger you are working on. Open the “inputs” tab and select the following type and model:...
Need help?
Do you have a question about the Geovane and is the answer not in the manual?
Questions and answers