Advertisement
5. OPERATING INSTRUCTIONS
5.1. LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. Dust from the removal of such paint is toxic and contact with it must be
avoided. The following action must be taken when using the sander on paint that you suspect may contain lead.
1.
User must determine potential hazard relating to age of paint to be removed (modern paints do not contain lead).
2.
DANGER! Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint dust:
Pregnant women, babies and children.
3.
We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Our ref SSP1699)
b) PE Coated Hooded Coverall (Our ref SSP266)
4.
Take adequate measures to contain the paint dust, flakes and scrapings.
5.
Continue to wear safety equipment as in (3) above and thoroughly clean all areas when the task is complete.
6.
Ensure that paint waste is disposed of, according to local regulations, in sealed bags or containers.
F
WARNING! Ensure that grinder is unplugged from the mains power supply before changing accessories.
5.2.
Preparation
p
5.2.1. Assemble grinding/cutting/sanding disc according to Section 3 and position the hand grip and safety
guard to suit the task.
5.2.2. Plug grinder into the mains power supply.
5.3.
ON/OFF Switch
5.3.1. The On/Off switch (fig 6.E) is designed to avoid accidental starting.
5.3.2. Once plugged into the power supply start the grinder by sliding the switch forward and pressing down.
F
WARNING! When the grinder first starts it will kick to the right. You must ensure, therefore, that
the tool is securely gripped in both hands. Especially important is the position you choose for the
p
side handle in order to maintain stability.
5.3.3. To turn off the machine press the switch at the rear and it will spring back to the ‘Off’ position.
F
WARNING! Before use, ensure that you are wearing approved safety goggles, ear defenders, appropriate dust
mask if dust will be generated and safety gloves, and that all other safety instructions in Section 1 are followed carefully.
p
5.4.
Grinding/Cutting/Sanding
5.4.1. The key to effective operating is controlling the pressure and surface contact between the disc and the workpiece.
F
WARNING! DO NOT switch the grinder on whilst the disc is in contact with the workpiece. Bring the rotating disc to the workpiece.
5.4.2. Allow the disc to reach full speed before starting to grind/cut/sand.
5.4.3. Grind flat surfaces with the disc at an angle of between 10 and 20 degrees to the workpiece. Too great an angle will cause a concentration
of pressure in one small area resulting in gouging or burning of the surface.
5.4.4. When grinding/cutting is complete allow the workpiece to cool. DO NOT touch the hot surface. Unplug the grinder from the mains power
supply, clean and store in a safe, dry, childproof area.
6.
MAINTENANCE
F WARNING! Ensure that the grinder is disconnected from the mains power supply before attempting any maintenance.
6.1.
Cleaning
6.1.1. Keep the grinder ventilation slots clean and free from obstructions. If available, blow compressed air into the vents to clear any internal
dust (safety goggles must be worn when undertaking this process). Keep the outer case of the grinder clean and free from grease.
DO NOT wash with water or use solvents or abrasives.
6.2.
Changing the motor brushes
6.2.1. Remove the rear cover.
6.2.2. Release the tension spring from the carbon brush and slide it out of the brush holder.
6.2.3. Disconnect the brush connector from the terminal.
6.2.4. Refitting is a reversal of the above procedure.
6.2.5. Repeat for the second brush.
7.
DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY We, the sole importer into the UK, declare that the product listed here is in conformity with the following
standards and directives.
100
& 115
720W ANGLE GRINDERS
MM
MM
Models SG101 & SG115
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
93/68/EEC CE Marking Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds,
Suffolk.
c) Latex Gloves (Our ref SSP24).
The construction file for this product is held by the Manufacturer and may
be inspected, by a national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Tools.
01284 757500
01284 703534
Lock “ON”
8th May 2003
e-mail
sales@sealey.co.uk
fig. 6
E
Release
“OFF”
9A>
www.sealey.co.uk
SG101 & SG115 - 2 - 080503
Advertisement
