SITEMANAGER 10xx/14xx/32xx/34xx
A
DIN Rail Mounting
Push the SiteManager from down and
upwards to apply tension on the
spring-lock, and in the same movement
push the SiteManager in, and over the
top of the DIN rail.
Note: In order for this product to conform with the safety certifications, this product must be
installed in a Restricted Access Location.
POWER
B
SiteManager must be fed 12 - 48V DC. Power consumption is max. 6W for the unit including the
integrated broadband modem (xx39 models) or optional USB mounted broadband modem
(xx29 models)
Power should be applied to the GND and +V terminals only!
Note: Under-powering the SiteManager may result in external USB devices to fail.
It is recommended to connect the earth ground in order to reduce interference of noise.
Ethernet ports
C
Use a standard Ethernet patch cable (straight or cross over) to connect the UPLINK1 port to a
switch in a network that has access to the Internet.
The DEV port can be connected to an existing network separate from the UPLINK1 network, or
you can create a separate device network isolated from the UPLINK1 network. But you can also
just connect the UPLINK1 port, and only access equipment on the Uplink side.
SiteManager 10xx and 32xx models:
192.168.2.100/24
DO NOT CONNECT THE
DEV AND UPLINK1
PORTS TO THE SAME
PHYSICAL NETWORK
SiteManager 14xx and 34xx models:
192.168.2.100/24
DO NOT CONNECT THE
DEV AND UPLINK1
PORTS TO THE SAME
PHYSICAL NETWORK
Release and ensure that the
SiteManager it is firmly mounted
192.168.2.2/24
IP 10.0.0.2
192.168.2.2/24
DO NOT ASSIGN DEV
ADDRESS IN THE SAME
LOGICAL NETWORK AS
UPLINK1
192.168.2.5/24
192.168.2.2/24
192.168.2.2/24
DO NOT ASSIGN DEV
ADDRESSES IN THE
SAME LOGICAL
NETWORK AS UPLINK1
192.168.2.5/24
Secomea A/S - Smedeholm 12-14 - DK2730 Herlev - Denmark
Tel: +45 8870 8650 - www.secomea.com - support@secomea.com
D
Applying UPLINK settings for accessing the Internet
The SiteManager requires being able to access the Internet via an Uplink port in order to
target a GateManager server. By default it will receive its IP address by DHCP, and you only
need to manually configure the Uplink if you will use a fixed IP on UPLINK1, or if you want to use
UPLINK2 as wireless Internet access.
Select one of the following 4 methods:
Using the Secomea Appliance Launcher.
1.
a.
Download and install the Appliance Launcher tool from here:
http://info.secomea.com/appliance-launcher.
b.
Connect the DEV1 or UPLINK1 port of the SiteManager to the local network and
power it on. The SiteManager must be on the same Subnet as your PC. Alterna-
tively connect the SiteManager with an Ethernet cable directly to your PC.
c.
Power on the SiteManager and wait approx. 1 minute for it to become ready.
d.
Start the Appliance Launcher and the SiteManager should be listed in the first
screen. If it does not appear immediately, try pressing the Search button a couple
of times. (Note that the Appliance Launcher will only show the SiteManager if your
PC has a genuine private IP address (10.x.x.x, 172.16-31.x.x, 192.168.x.x or 169.254.x.x))
e.
Follow the Wizard and set the UPLINK1 address if you want to use a fixed IP ad-
dress, or continue the wizard to menu UPLINK2 to set the SSID/WiFi Key for an
optional USB WiFi module, or PIN Code for an integrated or optional broadband
modem.
Using the default IP address (10.0.0.1)
2.
a.
Connect the DEV1 port of the SiteManager to the Ethernet port of your PC using a
standard Ethernet cable.
b.
Configure your PC's Ethernet adapter to 10.0.0.2 subnet mask 255.255.255.0.
c.
Power on the SiteManager and wait approx. 1 minute for it to become ready.
d.
Type the following in your web browser: https://10.0.0.1
e.
Login with user admin and the SiteManagers MAC address as password.
f.
Enter menu System --> UPLINK1 to set the UPLINK1 address if you want to use a
fixed IP address, or enter menu UPLINK2 to set the SSID/WiFi Key for an option al
USB WiFi module, or PIN Code for an integrated or optional broadband modem.
g.
Continue with section E to configure GateManager settings.
Using a DHCP server
3.
a.
Connect the UPLINK port of the SiteManager to your local network and power it on.
b.
After approx. 1 minute the SiteManager should have received an IP address from
your DHCP server.
c.
Check the lease list of the DHCP server to see what the IP address is.
d.
Type the IP address in your web browser preceded with https:// (e.g.
https://192.168.41.13).
e.
Login with user admin and the SiteManagers MAC address as password.
f.
Enter menu System --> Uplink1 to set the UPLINK1 address if you want to set a
fixed IP address, or enter menu UPLINK2 to set the SSID/WiFi Key for an optional
USB WiFi module, or PIN Code for an integrated or optional broadband modem.
g.
Continue with section E to configure GateManager settings.
Using a USB memory stick
4.
a.
Login to the GateManager Portal and locate the domain in which the SiteManager
should connect.
b.
Click the "USB Configuration" symbol
settings. If the SiteManager is connected to a local Intranet with a DHCP server,
you do not have to configure anything.
c.
Click create to save the configuration file locally to your PC.
d.
Copy the configuration file to a fat32 formatted USB memory stick.
e.
Power ON the SiteManager and wait until the SiteManager is ready (Status has
stopped blinking)
f.
Insert the memory stick, and wait until the SiteManager has automatically re-
booted. If the SiteManager has GateManager access, STATUS should turn green.
g.
Remove the memory stick. No further configuraiton is needed.
Applying settings for connecting to a GateManager server
E
1.
In the SiteManager Web GUI enter the menu GateManager --> General (if using the Appli-
ance Launcher, follow the wizard to the GateManager Parameters page).
2.
Enter the IP address of the GateManager server that the SiteManager should connect
to, and a Domain Token for the domain where the SiteManager should appear. You should
have received this information from your administrator or from where you received the
SiteManager.
IP 10.0.0.2
3.
When the settings are entered, you should reboot the SiteManager. Observe that the
Status LED goes steady Green, which indicates that the SiteManager is connected to the
GateManager.
4.
Once attached to the GateManager, you can use the GateManager Console or a Link-
Manager Client to get remote access to the SiteManager Web GUI to perform additional
configuration (DEV ports, Agents etc.)
5.
Detailed guides, new firmware etc. can be downloaded from
INITIAL SETUP
, and set the UPLINK1 or UPLINK2 port
Applicable to SiteManager models: 1029, 1039, 1429, 1439, 3229, 3239, 3429, 3439
DOC: SM10xx-14xx-32xx-34xx_initial_contact_v017
http://support.secomea.com
Need help?
Do you have a question about the SITEMANAGER 14 Series and is the answer not in the manual?
Questions and answers