Advertisement
Quick Links
Advertisement
Related Manuals for NCR X Series
Summary of Contents for NCR X Series
- Page 1 KIT INSTRUCTIONS X-Series Integrated Keypad 7702-K149/K349 Issue D...
-
Page 2: Revision Record
NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current. - Page 3 X-Series Integrated Keypad This kit provides an Integrated Keypad for the following 15" Displays: • RealPOS XR7 (7702) POS • RealPOS XR7 Plus (7703) POS • RealPOS 5968 X-Series Display Note: 7702-K349 includes these keytips and lenses: • 1x1 "00" Key, Black (Qty. 1) •...
-
Page 4: Installation Procedure
X-Series Integrated Keypad Installation Procedure XR7/XR7 Plus POS 1. Lay the terminal face down on a flat surface, using a protective foam/cloth. 2. Remove the Base Stand and Rear Cover assembly. a. Loosen the captive screws (2) that secure the Rear Cover to the chassis. b. - Page 5 X-Series Integrated Keypad 3. Remove the Display Collar (9 screws). 4. Remove the Blank Plate (left side of terminal, right side is for MSR) from the Display Collar. The plate is connected to the Display Collar with a strong adhesive. Use care when removing it to not damage the Display Collar.
- Page 6 X-Series Integrated Keypad 5. Install the Keypad onto the Display Collar (2 screws). 6. Route the Keypad Cable through the Cable Guide on the Display Collar. Note: Limit the amount of cable from the Cable Guide to 2.5" for the RealPOS XR7.
- Page 7 X-Series Integrated Keypad 7. Reinstall the Display Collar on the terminal. 8. Connect the Keypad Cable and Ground Wire to the Motherboard. Caution: Pull up and down on the cable at the Cable Guide to make sure they are not pinched under the Display Collar. 9.
- Page 8 X-Series Integrated Keypad X-Series Displays 1. Lay the terminal face down on a flat surface. Caution: Always use a soft material (cloth, foam) to protect the display screen when placing the terminal face down. 2. Remove the screws (4) that secure the Mount to the display.
- Page 9 X-Series Integrated Keypad 3. Remove the Rear Cover screws (2). 4. Pivot the Rear Cover as shown to remove it. 5. Remove the Display Collar (9 screws).
- Page 10 X-Series Integrated Keypad 6. Remove the Blank Plate (left side of terminal, right side is for MSR) from the Display Collar. The plate is connected to the Display Collar with a strong adhesive. Use care when removing it to not damage the Display Collar. 7.
- Page 11 X-Series Integrated Keypad 9. Reinstall the Display Collar on the terminal. 10. Connect the Keypad USB Cable to the PCB. 11. Connect the Keypad Ground Wire under the PCB mounting screw. 12. Replace the Base Stand and Rear Cover assembly on the display.
-
Page 12: Keypad Driver
X-Series Integrated Keypad Keypad Driver The NCR USB Utilities package for the Keypad module is located in the following location: http://www5.ncr.com/support/support_drivers_ patches.asp?Class=External/Terminals\7702XR7\Windows\F149Module\display Refer to the Readme document for the driver installation instructions. Keypad/Keyboard Remap Utility The NCR POS Keyboard Remap Utility provides a graphical user interface for keyboard remapping for 5932 Keyboards, and 5953, 5954, and X-Series Dynakeys.