Advertisement
2. INTRODUCTION & SPECIFICATION
2.1 Introduction.
The SM96 is a heavy-duty mortising machine suitable for cutting mortises up to 25mm for joints, locks and dead-bolts. Vertical assembly with
hydraulic damper, scale measure, adjustable depth and headstock stops. Horizontal assembly with scale measure, adjustable table and work stop for
repetitive work. Table has a complete clamping system with vice and two clamps. Two hand wheels for table adjustment. The integral drill chuck is
easily accessible from both sides of the head. Powered by a heavy-duty induction motor with no-volt release switch to prevent accidental restart after a
power failure or a jam. The mortiser is supplied with 16mm drill chuck, 1" mortising chisel and bit, chuck key and hex keys. Mounted on a stand, which
can be used as a parts cabinet.
2.2 Specification.
Model No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SM96
Chisel Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . ¼" to 1"
Chuck Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16mm
Spindle Travel . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220mm
Chisel Centre-fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145mm
Table Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400 x 150mm
Base Size . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 x 450mm
Spindle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400rpm
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz 750W
Dimensions (H x L x W) . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1530 x 550 x 820mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99kg
3. CONTENT & ASSEMBlY
3.1.
Contents
3.1.1
Unpack the product and check contents. Should there be any damaged or missing
parts contact your supplier or shipping agent immediately.
3.2.
Assembly
WARNING! DO NOT plug the mortiser into the mains power supply until
completely assembled and these instruction tell you to do so.
3.2.1
Do not allow brake fluids, petroleum or penetrating oils to come into contact with
plastic parts of the mortiser as damage may result.
3.2.2
Remove the mortiser and stand from the shipping containers. Before assembling, read
the instructions thoroughly and familiarise yourself with the correct maintenance
procedures and the safety precautions outlined in Section 1.
3.2.3
The mortiser should be secured to the stand with the four M12 x 120 hexagonal bolts
provided using the holes in the base. Ensure that there is enough room on each side
of the mortiser for the size of stock you intend using.
WARNING! The mortiser requires a 3-pin earthed mains socket. If you are not sure
whether the mains socket is properly earthed, consult a qualified electrician.
4. ADJUSTMENTS
4.1
Installing Chisel and Bit (Refer to Fig. 1)
4.1.1
Loosen the lock screw.
4.1.2
Insert the chisel into the head. Tighten the screw sufficiently to hold the
chisel in place.
NOTE: Set the slot in the side of chisel to the left or right, NOT to the back or
front. This will allow chippings to escape when cutting mortises.
4.1.3
Push the chisel up into the head as far as possible. Then lower the
chisel by between 0.8mm and 1.6mm. Tighten the lock screw to hold the
chisel in place.
4.1.4
Push the bit up through the chisel opening until the end of the bit is level
with the end of the chisel. Tighten the lock screw. Lock the drill bit in
place with the chuck key.
4.1.5
Loosen the lock screw and push the chisel up against the bushing. This
will give the required gap between the end of the bit and the end of the
chisel.
4.2
Mounting the Work Stop (Refer to Fig. 2)
4.2.1
The work stop is mounted to the table as shown in fig. 2.
5. OPERATING INSTRUCTIONS
WARNING! Ensure you read, understand and apply Section 1 Safety Instructions
before use.
5.1.
Set the depth stop to the required depth of cut. Refer to fig. 3.
5.2
Place the workpiece on the table and clamp it with the vice. Use the left hand wheel to
move the table forwards or backwards to suit the position of the mortise on the
workpiece.
5.3
Adjust the table stops according to the length of cut required then tighten the thumb
screws. Refer to fig. 4.
5.4
Switch on the mortiser and feed the chisel and bit steadily into the workpiece by
pulling down the operating handle.
NOTE: The rate of feed must be fast enough to prevent burning at the tip of the bit, yet not so
fast as to cause the machine to slow, or stall.
Original Language Version
Fig. 1
Fig. 3
SM96
Fig. 2
Issue: 2 - 25/03/10
Advertisement
