Sony KDL-26S2000 Quick Setup Manual

KDL-26S2000
KDL-32S2000
KDL-40S2000

Quick Setup Guide

For further information, see the operating instruction supplied with the TV.
Please retain this guide for your future reference.
For service and technical assistance, call our Customer Information Service Center (Toll Free):
US residents: 1-800-222-SONY (7669)
Canadian residents: 1-877-899-SONY (7669)
or visit: http://www.sony.com/TVsupport
DO NOT RETURN TO THE STORE
Sony Corporation © 2006
Printed in Japan
Making Audio/Video Connections
Your new TV includes various types of video inputs and two types of audio jacks;
composite-RCA type and digital audio (optical).
Use the outputs/inputs that are available on your components that provide the best
video/audio performances:
Best Audio/Video
Connector type
Performance
Digital Optical
OPTICAL
OUT
Digital Coaxial
Will require an adapter
to connect to this TV's
digital audio output.
Analog Audio
The connection diagrams shown below and on the reverse side are recommendations only;
other possible solutions may exist. Connections that include an AV receiver can often be
complex, so check your AV receiver's instruction manual for additional details.
See the "Cables Required" chart that appears with the diagram to determine which cables you'll
need. Depending on the components you plan to connect, you may need to purchase extra cables.
A
Use this diagram if you have;
VCR
If your DVD player has an HDMI jack, use that
instead of the video connections shown here.
PC
Rear of TV
7
RGB
AUDIO
PC IN
VIDEO IN
1
S VIDEO
VIDEO
L
(MONO)
AUDIO
R
DVD Player
2-671-017-11(2)
Connector type
HDMI (High-Definition
Multimedia Interface)
DVI
(Digital Visual Interface)
Will require an adapter to connect to this TV.
Component video
S VIDEO
Composite video
Cables Required
Splitter
Coaxial
DVD
PC
Composite
Player
Component
Audio
HD15-HD15
Splitter
6
VHF/UHF
R AUDIO L
HD/DVD IN
(1080i/720p/480p/480i)
3 4 5
Y
OPTICAL OUT
P
B
P
R
AUDIO OUT (VAR/FIX)
L
AUDIO
R
LINE IN
LINE OUT
R L
AUDIO VIDEO
Running Initial Setup
1
POWER
Press to turn on the TV.
The Initial Setup screen appears.
2
Press V/v to highlight the on-screen display
language. Then press
The message "First please connect cable/
antenna. Do you want to start Auto
Program?" appears.
3
Press B/b to highlight "OK" then press
The message "Auto Program" appears. Then
the message "Continue programming digital
channels?" appears. This may require 50+
minutes for completion.
4
Press B/b to highlight "OK" then press
When Initial Setup is complete, the TV will display the total number of analog
channels or the total number of digital channels found.
To run Auto Program again at a later time
Refer to the manual on "Initial Setup" and "Auto Program" sections.
The default setting for channel selection is Cable On. For antenna connections, run the Auto
Program again after selecting Cable Off from the settings.
B
1
Use this diagram if you have;
3
Cable Box
1
or
1
Satellite Receiver
2
1
If your DVD player or satellite receiver has an
HDMI jack, use that instead of the video
connections shown here.
Cable
PC
DVD Player
VCR
IN
A / V
OUT
INPUT DVD VCR
Initial Setup
.
Please select your language
.
Auto Program
Programmed Channel:
.
DVD PC
AV Receiver
VCR
Player
If you are not using a cable box or
satellite receiver, connect your cable to
the VCR's RF IN jack.
Rear of TV
7
6
RGB
R AUDIO L
AUDIO
PC IN
HD/DVD IN
VIDEO IN
(1080i/720p/480p/480i)
1 3 4 5
S VIDEO
Y
OPTICAL OUT
P
B
VIDEO P
R
AUDIO OUT (VAR/FIX)
L
L
(MONO)
AUDIO
AUDIO
R R
TV
VIDEO
OUT
VIDEO
L
AUDIO
LINE IN
OUT
R
English
Español
Français
10
Now tuning
Cables Required
Splitter 1
Coaxial 4
Composite 3
Component 1
Audio 3
HD15-HD15 1
Cable
Splitter
VHF/UHF
Cable Box or
Satellite Receiver
SAT IN
IN
OUT
VCR
LINE IN
IN
LINE OUT
OUT
R L
AUDIO VIDEO
Continued ,