Download Print this page

Advertisement

Available languages

Available languages

Quick Links

G11 HVLP SPRAY GUN GUIDE
Table of Contents
Parts Desription
1
Setup + Use
2
Cleaning + Maintaining
5
Trouble Shooting
6
1 5 L i n c o l n S t r e e t H a w t h o r n e , N J 0 7 5 0 6 U S A
T e l : 9 7 3 . 4 2 3 . 9 2 6 6
F a x : 9 7 3 . 4 2 3 . 9 2 6 4
s i m a l f a . c o m

Advertisement

loading
Need help?

Need help?

Do you have a question about the G11 HVLP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SIMALFA G11 HVLP

  • Page 1 G11 HVLP SPRAY GUN GUIDE Table of Contents Parts Desription Setup + Use Cleaning + Maintaining Trouble Shooting 1 5 L i n c o l n S t r e e t H a w t h o r n e , N J 0 7 5 0 6 U S A T e l : 9 7 3 .
  • Page 2 Simalfa G11 | Needle Packing Nut G11-08 Simalfa G11 | Air Valve Shaft G11-09 Simalfa G11 | O-Ring (9x1) - [Included on Brass Air Valve Body Set] G11-10 Simalfa G11 | O-Ring (10.6x1.65) - [Included on Brass Air Valve Body Set] G11-11...
  • Page 3 This is where the atomization airline is attached. We suggest using both the atomization air regulator contained within the Simalfa spray gun and a wall regulator to insure proper atomization. Learn about setting the proper atomization air in the next section titled “Setting Atomization Air Pressure”.
  • Page 4 A. Correct Atomization Air Pressure. Atomization air is set correctly for the fluid volume and pattern. Simalfa appears in fine droplets to maximize the efficiency and performance. B. Incorrect Atomization Air Pressure. Droplets too coarse for the pattern width and fluid volume.
  • Page 5 S E T U P + U S E Recommended Spray Techniques Distance from Substrate. When applying Simalfa the spray gun should be held at a distance between 6”-10” (15cm - 25cm) from the substrate. Pattern Width. Keep it narrow. A narrow spray pattern gives greater control over where the adhesive is applied.
  • Page 6 C L E A N I N G + M A I N T A I N I N G WARNING: Prior to any servicing and repair work the spray gun must be removed from atomizing air pressure and material inputs. Procedures to always follow: 1.
  • Page 7: Troubleshooting

    T R O U B L E S H O O T I N G WARNING: Prior to any servicing and repair work the spray gun must be removed from atomizing air pressure and material inputs. S Y M P T O M C A U S E R E M E D Y Adhesive is dripping after trigger is...
  • Page 8: Limpieza Y Mantenimiento

    G11 HVLP SPRAY GUN GUIDE Tabla de Contenidos Descripción de partes Configuración + Uso Limpieza y mantenimiento Solución de inconvenientes 1 5 L i n c o l n S t r e e t H a w t h o r n e , N J 0 7 5 0 6 U S A T e l : 9 7 3 .
  • Page 9 Simalfa G11 | Needle Packing Nut G11-08 Simalfa G11 | Air Valve Shaft G11-09 Simalfa G11 | O-Ring (9x1) - [Included on Brass Air Valve Body Set] G11-10 Simalfa G11 | O-Ring (10.6x1.65) - [Included on Brass Air Valve Body Set] G11-11...
  • Page 10 Controles de la pistola + Entradas A. Control del abanico Esta perilla controla como va a salir el adhesivo Simalfa de la pistola. A medida que la perilla es enroscada en la pistola (Apretada) el abanico será más estrecho. A medida que la perilla es desenroscada, el abanico será...
  • Page 11 A. Presión correcta de aire La atomización de aire es correcta para la configuración de flujo de adhesivo y abanico utilizado. Simalfa aparece en finas gotas maximizando así la eficiencia y rendimiento. B. Presión incorrecta de aire.
  • Page 12 Abanicos muy anchos pueden generar desperdicio, suciedad y nube. Angulo al sustrato. Aplicar Simalfa directo al sustrato, no en ángulo a lo largo. Esto asegurara aplicación mas económica y reducirá el potencial de nube.
  • Page 13 L I M P I E Z A Y M A N T E N I M I E N T O ¡ADVERTENCIA! Antes de realizar trabajos de limpieza o mantenimien- to se debe retirar las conexiones de aire y de fluido de adhesivo. Procedimientos obligatorios: 1.
  • Page 14 S O L U C I Ó N D E I N C O N V E N I E N T E S ¡ADVERTENCIA! Antes de realizar trabajos de limpieza o manten- imiento se debe retirar las conexiones de aire y de fluido de adhesivo. S Í...

This manual is also suitable for:

PremiumG11