Dynasty DBQ Series Service

Outdoor gas grill

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Service

This manual is to be used by qualified appliance

technicians only. Maytag does not assume any

responsibility for property damage or personal

injury for improper service procedures done by

an unqualified person.

Outdoor

Gas Grill

This Base Manual covers, but is

not limited to the following:

January 2005

DBQ*

JBQ*

MBQ*

16025981

Table of Contents

Need help?

Do you have a question about the DBQ Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Dynasty DBQ Series

Page 1 Service This manual is to be used by qualified appliance technicians only. Maytag does not assume any responsibility for property damage or personal injury for improper service procedures done by an unqualified person. Outdoor This Base Manual covers, but is not limited to the following: Gas Grill DBQ*...
Page 2: Important Information
Important Information Important Notices for Servicers and Consumers Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and workmanship go into every product to provide our customers with quality products. It is possible, however, that during its lifetime a product may require service.
Page 3: Table Of Contents
Table of Contents Important Information ............ 2 Disassembly Procedures Safety Information Removing and Replacing Built-In Unit ...... 12 Safety Practices for Servicer ........4 Hood Thermometer ..........12 Servicing ..............4 Hood Handle ............12 ALL APPLIANCES ........... 5 Front Hood / Spit Saddle Brackets ......12 Precautions ..............
Page 4: Safety Information
Safety Information As with all appliances, there are certain rules to follow for safe operation. Verify everyone who operates the grill is familiar with the operations and with these precautions. This gas appliance contains or produces a chemical or Use appliance only for its intended purpose as described. chemicals which are known to the state of California to Pay close attention to the safety sections of this manual.
Page 5: All Appliances
Safety Information 6. Check grill when service is completed—After Gas Supply Pressure servicing, make visual checks on electrical connection, and check for gas leaks. Inform CAUTION consumer of the condition of grill before leaving. To avoid property damage, maximum gas supply 7.
Page 6: Gas Connection
Safety Information Testing for Gas Leaks Gas Connection Connect gas supply to regulator using hard pipe or a WARNING flexible connector. Pressure regulator supplied with this appliance has a ½-inch NPT female connection. To avoid property damage or serious personal injury, never use a lighted match to test for gas leaks.
Page 7: Product Safety Devices
Safety Information Product Safety Devices Safety devices and features have been engineered into the product to protect consumer and servicer. Safety devices must never be removed, bypassed, or altered in such a manner as to defeat the purpose for which they were intended. Listed below are various safety devices together with the reason each device is incorporated in the gas ranges.
Page 8: General Information
General Information General Information This manual provides basic instructions and suggestions for handling, installing and servicing gas grills. The directions, information, and warnings in this manual are developed from experience with, and careful testing of the product. If the unit is installed according to the Installation Instructions, it will operate properly and will require minimal servicing.
Page 9: Model Identification
General Information Model Identification Receiving Grill Complete registration card and promptly return. If Inspect grill thoroughly at the time of delivery. registration card is missing: Immediately report any visible damage to carrier. Damage not discovered until after accepting delivery • For product information call 1-866-820-9401 or visit can still be claimed by using a concealed damage report the Web Site at www.jadeappliances.com form, available from the carrier’s agent.
Page 10: Troubleshooting Procedures
Troubleshooting Procedures WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires it. Problem Possible Cause Correction • Verify spark. Poor ground at ignitor ....... • Replace spark module Weak or failed spark module ....Burners will not ignite;...
Page 11: Component Testing Procedures
Component Testing Procedures WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and shut off gas to unit before servicing, unless testing requires power. Illustration Component Test Procedure Results Pressure regulator Verify gas pressure Water Column Pressure (WCP).
Page 12: Disassembly Procedures
Disassembly Procedures To avoid the risk of electrical shock, personal injury or death; shut off gas supply before following any WARNING disassembly procedure. Removing and Replacing Built-In Unit Knob Bezel(s) 1. Turn off gas supply to the grill. 1. Turn off gas supply to the grill. 2.
Page 13: Ignitor(S)
Disassembly Procedures To avoid the risk of electrical shock, personal injury or WARNING death; shut off gas supply before following any disassembly procedure. Ignitor(s) Spark Ignitor 1. Turn off gas supply to the grill. NOTE: First determine the spark ignitor that needs 2.
Page 14: Infra-Red Broiler Ignitor
Disassembly Procedures To avoid the risk of electrical shock, personal injury or death; shut off gas supply before following any WARNING disassembly procedure. Infra-red Broiler Bracket Side Burner 1. Turn off gas supply to the grill. 1. Turn off gas supply to the grill. 2.
Page 15: Typical Grill Component Layout
Disassembly Procedures To avoid the risk of electrical shock, personal injury or WARNING death; shut off gas supply before following any disassembly procedure. Thermometer Rotisserie Assembly Front Hood Bezel Hood Handle Rear Hood Smoker Assembly Infra-red Broiler Cooking Grates Spit Saddle Ignitors Brackets...
Page 16: Typical Base Unit
Disassembly Procedures To avoid the risk of electrical shock, personal injury or death; shut off gas supply before following any WARNING disassembly procedure. Drawer Slide Base Hinge Door Side Shelf Drawers Casters Typical Base Unit Side Burners Typical Side Burners 16025981 ©2005 Maytag Services...
Page 18 Instruction Sheet Description: L.P. Conversion for Outdoor Grill Series FOR YOUR SAFETY If you smell gas: 1. Shut off gas to the appliance 2. Extinguish any open flame 3. Open lid 4. If odor continues, immediately call your gas supplier or your fire department FOR YOUR SAFETY 1.
Page 19 Procedure: When converting outdoor grill gas valve to L.P. gas, be sure the incoming gas supply line is equipped with a pressure regulator (located ahead of the unit) that will maintain the gas supply to the grill. Surface Orifice Conversion: NOTE: All orifices with no exception must be converted.
Page 21 INSTALLATION AND USER MANUAL MODELS: DBQ-30 DBQ-30F DBQ-42 DBQ-42F DBQ-54 DSB-1 DSB-2 DYNASTY OUTDOOR GAS GRILL P/N 2420100000 08/03 B–2 16025981 ©2005 Maytag Services...
Page 22 Enjoy! And, welcome to our Dynasty family. This manual is intended to serve as a guide for the operation and maintenance of your new Dynasty Grill. Please read it carefully, and keep it handy for reference.
Page 23: Use And Care
WARNINGS AND NOTICES safety General Safety Requirements – WARNING 1. Installation of this appliance must conform with 6. California Proposition 65 local codes or, in the absence of local codes, with The burning of gas cooking fuel generates some either the National Fuel Gas Code, ANSI Z223.1, byproducts that are on the list of substances, which or CAN/CGA-B149.1, Natural Gas Installation are known by the State of California to cause cancer...
Page 24 Complete and return the warranty card. Please take a moment to fill out and mail the Warranty Card included with your Dynasty Grill. Make sure you enter the model and serial numbers of your new appliance on the Warranty Card.
Page 25 SAFETY INSTRUCTIONS Please read before installing and operating your new Dynasty Grill safety General Precautions 1) Your Dynasty gas grill should be properly installed 9) Never grill without the drip pan in place and pushed and serviced. Refer to the installation instructions all the way to the back of the grill.
Page 26 2) Always use the proper size pan. Select utensils wear loose fitting or hanging garments while using with flat bottoms large enough to cover the burner. your Dynasty grill. The use of undersized utensils exposes the sides of the utensils to direct contact with a portion of the 8) Only use dry potholders –...
Page 27 Built-in Installation Your Dynasty grill is designed for easy installation into a non-combustible enclosure. The supporting deck and counter must be level and flat. When determining the final location for your grill it is required that ventilation holes be provided in the enclosure so that gas will not become entrapped in the event of a leak (See pages 8 and 9).
Page 28 CABINET CUT OUT DIMENSIONS FOR GAS GRILL AND ACCESSORIES installation CUT OUT ON CABINET BULLNOSE TYPICAL FOR GRILL, SIDEBURNER AND BARTENDER DIMENSIONS FOR CABINETS WITH BULLNOSE 16025981 B–9 ©2005 Maytag Services...
Page 29 Gas Requirements Your Dynasty grill is designed to work with either Natural Gas or with LP (Liquid Propane) Gas. Check your rating plate to make sure the gas supply you are hooking up to is the gas type the grill is manufactured for (see page 3).
Page 30 installation NOTE: An enclosure for an LP gas cylinder shall be vented by openings on the level of the cylinder valve and at floor level. The effectiveness of the opening(s) for purposes of ventilation shall be determined with the LP-gas supply cylinder in place.
Page 31 INSTALLATION OF YOUR DYNASTY GRILL (continued) installation Side Burner Attachment – Model DFB 1) Remove right side shelf, screws and brackets. 2) Pry off hole plug with a flat screwdriver. 3) Remove right door for easy access to the grill gas intake pipe.
Page 32 Installing Access Doors Models DAD-30 and DAD-42 installation 1. Provide cut out and door jamb with inside 6. Adjust doors as follows: dimensions as follows: a) For height adjustment, loosen the two screws 19 3/8” X 28 3/8” for DAD-30 and attached to each mounting plate.
Page 33 INSTALLATION OF YOUR DYNASTY GRILL (continued) installation Adjustments and Efficiency Prior to shipment each burner is tested and adjusted at the factory. Due to variations in the location, conditions, gas supply or when converting from one gas to another, readjustment of the burners may be necessary.
Page 34 9. Once adjusted, reverse steps to reassemble. Low Setting Adjustment Grill and Open Burners The valves on your Dynasty grill feature an adjustable low setting. Due to fluctuations in gas pressure, heating value or gas conversion, you may feel it necessary to increase or decrease gas flow in the low position.
Page 35 INSTALLATION OF YOUR DYNASTY GRILL (continued) installation Leak Testing Perform a leak test at least once each year whether the gas supply cylinder has been disconnected or not. In addition, anytime the gas cylinder is connected to the regulator or any part of the gas system is disconnected or replaced, conduct the leak testing.
Page 36 Leak Testing Procedure installation (continued) 7. If you are unable to stop a leak, shut off the gas supply at the cylinder valve. Remove the cylinder from the grill. Call an authorized gas appliance service technician or LP gas dealer. Do not use the appliance until the leak is corrected.
Page 37 FEATURES OF YOUR GRILL operation Feature Index See page Operation 18-20 1 Grill Cleaning 32-35 Operation 24-25 2 Top Burners Flame Height Operation 3 Smoker Drawer Operation 22-23 4 Rotisserie Cleaning 5 Grill Racks Cleaning 6 Drip Tray Cleaning 7 Exterior Surfaces 8 Questions? Easy Troubleshooting Guide 36-37...
Page 38 Prior to turning the gas on, inspect the gas supply piping or hose. Make sure only the supplied hose and regulator are being used. If signs of abrasion, cuts wear and tear, or other damage are noticed on the hose, it should be replaced. Contact your local Dynasty dealer for replacement parts. 16025981 B–19...
Page 39 USING YOUR GRILL operation Your Dynasty grill consists of a set of burners, a bed of side ported to minimize blockage for falling grease ceramic briquettes and a heat retaining cooking rack. and debris. Above the burners are stainless steel trays Each burner is rated at 25,000 BTU.
Page 40 Operating The Grill operation Make sure all burner controls are off. Do not attempt to light the burners if the smell of gas is present. For LP units, check the connection with a soap and water solution after attaching the hose. Make sure there is gas in the tank and it is sitting upright.
Page 41 USING YOUR GRILL (continued) operation Lighting The Grill Burners (continued) 7. Repeat the procedure or try “Manual Lighting procedure” below. 8. Upon successful lighting, repeat the process on the other burners you wish to light. 9. To shut off burners push in knob and turn to OFF. It is normal to hear a popping sound when the burners are turned off.
Page 42 USING THE SMOKER DRAWER operation The smoker drawer consists of a stainless steel slide out drawer positioned near the front just above the grill burners. It is designed for easy use. After deciding which wood chips to use (see chart below), soak them thoroughly in water, then place them into the drawer.
Page 43 USING YOUR ROTISSERIE operation The rotisserie burner is an infrared type, which heat is ideal for searing in the natural juices and provides intense searing radiant heat. Preferred by nutrients found in quality cuts of meat. professional chefs over other methods, this intense Cooking with the Rotisserie The rotisserie system is designed to cook items from the back using infrared heat.
Page 44 Lighting The Infrared or Rotisserie Burner operation 1. Open the hood. 2. Push in and turn counter clockwise the gas control knob for the IR (infrared) burner to the HI position. This is the knob farthest to the left. On units with two IR burners, the control knob for the right IR burner is the knob farthest to the right.
Page 45 USING THE TOP BURNERS operation Your Dynasty grill has optional top burners equipped with push button igniter for lighting. Lighting The Open Burners 1. Remove the burner cover, if any, or any cooking utensils from the burner grate. Caution: The burner cover may be hot if the grill burners are in operation.
Page 46 Manually Lighting the Open Burners (continued) operation 4. If the burner does not light after 5 seconds, turn the control knobs to the OFF position. Wait 45 seconds until the gas clears before attempting to light it again. 5. If the burner does not light after several attempts see troubleshooting guide on pages 36-37.
Page 47 Never attempt to handle a hot briquette tray. Cleaning the Stainless Steel Your Dynasty grill is made of all welded #304 stainless steel. This is a non- rusting and non-magnetic stainless steel. There are many different stainless steel cleaners available. Always use the mildest cleaning procedure first, scrub in the direction of the grain;...
Page 48 CLEANING AND MAINTENANCE (continued) cleaning Cleaning the Grill Burners The grill burners should be cleaned thoroughly before using your grill after long periods of storage and monthly during regular use. 1. Be sure the gas supply is off and the knobs are in the OFF position. Make sure the grill is cool.
Page 49 cleaning Cleaning the Heat Deflector The heat deflector will collect grease and food residuals. It should be removed and cleaned after every use. When removing the heat deflector, use care to avoid HEAT DEFLECTOR chipping its ceramic surface. Wash with a mild cleaner/degreaser, rinse and dry.
Page 50 QUESTIONS? USE THIS EASY TROUBLESHOOTING GUIDE questions PROBLEM WHAT TO DO 1. Remove the grill rack and the briquette tray. Watch the igniter tip as GRILL WILL NOT IGNITE you press the push button igniter. You should see a spark jump from the WHEN THE PUSH BUTTON igniter tip to the burner.
Page 51 questions questions PROBLEM PROBLEM WHAT TO DO WHAT TO DO 1. Is there a spark at the igniter? Check if the gap between the igniter 1. Is there a spark at the igniter? Check if the gap between the igniter ROTISSERIE WILL NOT ROTISSERIE WILL NOT electrodes is between 1/8 to 3/16 of an inch.
Page 52 This warranty shall apply only to products manufactured and located in the United States and Canada. Warranty labor shall be performed by an authorized DYNASTY service agency or representative.
Page 54 THE DYNASTY BAR TENDER INSTALLATION, USE AND CARE MANUAL MODELS: DBTA-18 DBTA-30 DBTA-30F 16025981 © 2005 Maytag Services...
Page 61 CLEANING AND MAINTENANCE The Dynasty Bar Tender is made of #304 stainless steel for long lasting beauty and service. It is non- rusting and non-magnetic. Use stainless steel cleaner to clean the unit. Mild soap and water can be used to wipe dirt.

This manual is also suitable for:

Jbq series Mbq series Dbq-30 Dbq-30f Dbq-42 Dbq-54 ... Show all

Dynasty DBQ Series Service

Quick Links

Need help?

Questions and answers

Related Manuals for Dynasty DBQ Series

Summary of Contents for Dynasty DBQ Series

This manual is also suitable for:

Table of Contents