Advertisement
Quick Links
Honeywell
12 Clintonville Road
Northford, CT 06472
http://www.honeywellpower.com
1 Overview
These Honeywell Rack Mount CCTV power supplies will provide 24 VAC power distributed via 16 circuits for powering
CCTV cameras and other video equipment. Each circuit will be fuse protected at 3.0A, or PTC protected at 2.5A. Fuses
are accessible directly through the front panel by removing six screws.
2 Specifications
•
Input: 117VAC, 60Hz, 2A.
•
Output: 8A @ 24VAC (200VA).
•
Maximum current rating:
– HPR2416UL: any output, 3A; total supply, 8A @ 24VAC**.
– HPR2416CBUL: any output, 2.5A*; total supply, 8A @ 24VAC**.
* PTC Protected Class 2 Power Limited Outputs.
** Outputs 1 to 8 provide 4A @ 24VAC (100VA).
** Outputs 9 to 16 provide 4A @ 24VAC (100VA).
•
16 outputs.
•
Surge and transient protection.
•
Transformer has built-in thermal protection.
•
Indicator Lights:
– Input Power Indicator (1 red): Illuminated power switch/circuit breaker.
– Output Power LEDs (16 green): ON indicates that AC is present at the related output circuit.
•
Overload Protection:
– Input power switch has built-in circuit breaker.
– AC line fuse (5 x 20mm glass).
– Individual output circuits have a glass fuse (5 x 20mm) or resettable PTCs.
– NOTE: To reset a PTC that has experienced an overload or short circuit, switch power off for 5 minutes to allow
the PTC to reset itself.
•
Factory installed three-conductor AC line cord.
•
Unit maintains camera synchronization.
•
2U rack chassis for use in standard EIA 19" rack.
•
Removable rear terminal blocks.
•
Line power rocker switch with built-in circuit breaker indicates power on with red neon lamp.
•
Designed for quick installation.
•
Maximum Temperature Range: 32°F to 120°F (0°C to 49°C); for indoor use only
WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
!
THIS APPLIANCE TO RAIN OR MOISTURE.
For continuous protection against hazard, replace fuses only with exact type and rating. All 117V wiring should be
routed so that it cannot touch 24V wiring; minimum spacing 3/8" (0.953cm). This installation should be made by a
qualified service person and should confirm to all local codes. Install in accordance with the National Electrical
Code.
• HPR2416UL • HPR2416CBUL
CCTV Rack Mount Power Supply/Distribution Units
PN 52992:A
Product Installation Document
5/23/06
ECN 07-005
Advertisement
Related Manuals for Honeywell HPR2416CBUL
Summary of Contents for Honeywell HPR2416CBUL
-
Page 1: Specifications
1 Overview These Honeywell Rack Mount CCTV power supplies will provide 24 VAC power distributed via 16 circuits for powering CCTV cameras and other video equipment. Each circuit will be fuse protected at 3.0A, or PTC protected at 2.5A. Fuses are accessible directly through the front panel by removing six screws. -
Page 2: Installation Instructions
3 Installation Instructions Unpack product. Do not discard packing materials until installation and checkout are successfully completed. Mount unit in 19” rack only. Do not obstruct side air vents. Verify that power switch on back of unit is in the OFF position (See Figure 2 - Rear View of Power Supply). Plug power cord into grounded 117V, 60Hz receptacle. - Page 3 •Replace and secure front panel. – The PTCs on the HPR2416ULCB will reset automatically while power is off. – Plug power cord into receptacle. – Set power switch on back of unit to the ON (RESET) position. Figure 1 - Power Supply with Front Panel Removed 52992bd1.wmf Continued on next page...
- Page 4 Figure 2 - Rear View of Power Supply FOR CONTINUED PROTECTION DO NOT OPEN AGAINST A RISK OF FIRE, REPLACE HPR2432600UL HPR2432600CBUL ALL FUSES WITH THE SAME TYPE RISK OF ELECTIC SHOCK AND RATING (3A, 250V) REFER TO PRODUCT INSTALLATION DOCUMENT COMMERCIAL CLOSED-CIRCUIT PN 52___ DO NOT EXPOSE UNIT TO RAIN OR...
- Page 5 Figure 3 - Dimesnsions hprdimensions.wmf For additional information: • Visit our website at http://www.honeywellpower.com • Contact Technical Support at 1(877) HPP-POWR • E-mail us at hpp_techserv@honeywell.com HPR2416UL(CB) Installation Document P/N 52992:A 5/23/06...