Related Manuals for ensto Chago eFill Series
Summary of Contents for ensto Chago eFill Series
- Page 1 Chago eFill Installation instructions Operation instructions RAK 93 18.5.2018 ©Ensto 2018...
-
Page 2: Table Of Contents
Charging Current Limitation Top Cover Installation Plug Holder Installation User Instructions Troubleshooting The vehicle is not charging The indicator light is red The vehicle is charging slower than it should Maintenance Instructions Warranty Dimension Drawing Technical Data RAK93 / © Ensto 2018... -
Page 3: Chago Efill Charging Point
At the bottom of the wall bracket lies a small hole for padlock for extra security against theft of the charging point. • Install the plug holder in a suitable location near the charging point. See “Plug Holder Installa- tion” and figure 5 on page 8. RAK93 / © Ensto 2018... -
Page 4: Evh020.01 And Evh020.02 / Evh050.02
NOTE! The installation must be done by a qualified person e.g. an electrician. See figure 2. Figure 2 Cable lead through Cable lead through plate orientation if plate orientation if cable entry is from bottom cable entry is from rear Rubber washer Possible supply cable entry directions RAK93 / © Ensto 2018... -
Page 5: Supply Connection Evh020.01 And Evh020.02 / Evh050.02
In case of an eFill with a pushbutton, connect the cable of the pushbutton according to the connection diagram. IMPORTANT NOTICE: eFill needs to be installed to a dedicated supply line, which is equipped with 30mA residual current device (RCD) and 16A circuit breaker (MCB). Figure 3 RAK93 / © Ensto 2018... - Page 6 EVI020 DIP4 OFF DIP5 OFF DIP6 OFF PG = ProximityGround L1 N L1 N CP = ControlPilot X1 16A L1 N PEPE SUPPLY 1 x 16A 230V max 6mm² Cu 30mA RCD and 16A MCB RAK93 / © Ensto 2018...
-
Page 7: Charging Current Limitation
To get to the control unit the front cover must be removed by loosing the four torx screws. DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 Maximum charging current 8A (EVH020.01R / EVH020.02R default) 16A (EVH020.01 / EVH020.02 and EVH020.01R16 / EVH020.02R16 default), 3 x 16A EVH050.02 / EVH050.02R16 default RAK93 / © Ensto 2018... -
Page 8: Top Cover Installation
• Prepare the wall for installation and use screws deliv- ered in the package. • Install the holder to the wall. After installation, place the charging plug to the holder. See figure 5. Figure 5 RAK93 / © Ensto 2018... -
Page 9: User Instructions
Missing protective earth (PE). Check the PE availability from the supply line and condition of the charging cable. • Error in the vehicle communication. Disconnect the vehicle, reset the charging point by turn- ing supply voltage off and on. Retry charging. RAK93 / © Ensto 2018... -
Page 10: The Vehicle Is Charging Slower Than It Should
Ensure that there is no charging current limitation features in use at the vehicle. If you need to contact Ensto related to faulty operation of Chago eFill, prepare to tell the order num- ber (V..). You will find the order number on the nameplate on the enclosure bottom. -
Page 11: Dimension Drawing
Dimension Drawing EVH020.01 / EVH020.02 / EVH050.02 EVH020.01R / EVH020.01R16 and EVH020.02R / EVH020.02R16 /EVH050.02R16 RAK93 / © Ensto 2018... -
Page 12: Technical Data
-30 … +50 oC Operating humidity 95% non condensating Standby power con- <1W typical sumption Functional features Status indicator LED’ s Ensto Chago Oy Ensio Miettisen katu 2, P.O. Box 77 FIN-06101 Porvoo, Finland Tel. +358 20 47 621 Support: https://www.ensto.com/support/service-request/...