Drip Tray For The Cups; Water; Temperature Controller; Push-Button Switch On / Off - Profi Cook PC-HWS 1168 Instruction Manual

Drip Tray for the Cups

1. Slide the drip tray into the recess of the housing until it
stops. It must audibly click into place.
2. Put on the stainless steel overlay.
3. To remove the drip pan, lift it slightly.

Water

The fresh drinking water you fill in the water tank should
have a temperature of 22 °C to 28 °C. Do not fill with water
that has a temperature of above 35 °C or below 15 °C. This
could lead to deviations in the temperature of the dispensed
water.

Temperature Controller

Use this controller to select the temperature at which the
water is to be dispensed.

Push-Button Switch ON / OFF

Use this control to turn the appliance on and off. The
push-button switch performs the following functions when
engaged or disengaged:
Push-button
OFF
disengaged:
switch
The appliance
is switched off.
Illuminated in red ---
Illuminated in green ---

Electric Connection

Ensure that your mains power corresponds with the speci-
fications of the appliance. The specifications are printed on
the type label.

Connected Wattage

The total power consumption of this appliance can be up
to 2600 W. With this connected load a separate supply line
protected by a 16 A household circuit breaker is recom-
mended.
CAUTION: Overload!
• If you use extension leads, these should have a cable
cross-section of at least 1.5 mm².
• Do not use any multiple sockets, as this appliance is
too powerful.

Connection

1. Check the switch position! The push-button switch
must be disengaged.
2. Connect the mains cable to a properly installed and
earthed wall outlet.
38
PC-HWS1168_IM
Prior to the first use, let the maximum tank content run
through the appliance while having the temperature setting
on 100 °C. This removes dust, which may have collected
during transport. Follow the instructions given under
"Operation". Do not use this water for consumption.
WARNING:
Danger of scalding due to escaping steam!
While preparing hot water keep your hands away from
the faucet.
1. Open the lid of the water tank.
2. You have two options to fill water into the water tank:
In case the water tank is placed on the housing, fill the
water by using a cup. You may also remove the water
tank beforehand and place it back filled.
3. Fill the water tank with clean drinking water maximum up
to the "2.2 L" mark.
4. Close the lid of the water tank.
ON
5. Place an empty container onto the drip tray.
engaged:
6. Use the temperature controller to select the desired
The appliance is
water temperature.
switched on.
7. Start the water dispenser by engaging the push-button
Preheating phase switch.
8. Once the desired amount of water has been dispensed,
Water dispenser
stop the water dispenser by disengaging the push-button
switch.
The water dispenser will not stop automatically!
The intervals at which you should remove lime-scale de-
pend on hardness of the tap water and operating time. If the
preparation time increases significantly, de-calcification will
be necessary. Regardless, we recommend de-scaling the
appliance once a month.
• Use only commercially available citrus acid-based de-
scaler.
• Dose as indicated on packaging or instruction leaflet.
• Dispense hot water with a temperature of 100 °C once.
Do not pour that water away immediately. As long as it
is hot you may still use it to de-scale the water faucet if
needed. Please observe the instructions that we have
included in the chapter "Cleaning".
WARNING:
• Afterwards, let the maximum tank content run through
the appliance while having the temperature setting at
100 °C to rinse out residues of the de-scaling agent.
• Do not use this water for consumption.

First Use

Operation

CAUTION:

De-scaling

12.10.18