Page 1
Camarin Collection | 414468 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987. English pg 1-26 Français pg 27-29...
Page 2
PENCIL DRAWER BOTTOM (1) LEFT SIDE (1) LEFT FRONT/RIGHT BACK (1) SMALL DRAWER BACK (1) REAR FOOT (2) BRACE (1) RIGHT FRONT/LEFT LARGE DRAWER BACK (1) REAR FOOT (2) SMALL DRAWER FRONT (1) D716 DRAWER BOTTOM (2) Page 2 414468 www.sauder.com/services...
CAM SCREW - 6 METAL CORNER KNOB - 3 NAIL - 22 HINGE - 2 BRACKET - 6 BRACKET - 4 CAM COVER - 4 METAL PIN - 7 GROMMET CAP - 1 GROMMET - 1 Page 4 414468 www.sauder.com/services...
Page 5
18S BROWN 1" FLAT HEAD SCREW - 4 SILVER 5/8" FLAT HEAD SCREW - 4 BLACK 1-1/8" MACHINE SCREW - 3 30S BLACK 1-9/16" FLAT HEAD SCREW - 8 SILVER 9/16" LARGE HEAD SCREW - 2 BLACK 1-1/4" FLAT HEAD SCREW - 2 www.sauder.com/services 414468 Page 5...
Page 6
Look for this icon. It means a Step 1 video assembly tip is available at www.sauder.com/services/tips Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=803...
Page 7
Turn six CAM SCREWS (8F) into the LEGS (T and U). å Remember: Fasten the LEGS (T and U) to the LEFT END (B). Tighten å Righty tighty. six HIDDEN CAMS. Lefty loosey. (6 used) Edge with HIDDEN CAMS Angled edge Angled edge www.sauder.com/services 414468 Page 7...
Page 8
NOTE: The CABINET RAILS are marked "CABINET å RIGHT" and "CABINET LEFT" for easy identifi cation. Roller end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Edge with CAM DOWELS Rounded edge Roller end Page 8 414468 www.sauder.com/services...
Page 9
GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. GOLD 5/16" FLAT HEAD SCREW (8 used in this step) Roller end Rounded edge Edge with CAM DOWELS Roller end Roller end Rounded edge Roller end www.sauder.com/services 414468 Page 9...
Page 10
Tighten Risk of damage or Arrow injury. HIDDEN CAMS must be completely Arrow Maximum tightened. HIDDEN 210 degrees CAMS that are not completely tightened may loosen, and parts may separate. To Minimum completely tighten: 190 degrees Page 10 414468 www.sauder.com/services...
Page 11
Fasten the MODESTY PANEL (F) to the LEFT END (B). å Tighten three HIDDEN CAMS. i t h o f a c S u r D E N H I D Maximum Arrow 210 degrees Minimum 190 degrees www.sauder.com/services 414468 Page 11...
Page 12
NOTE: Be sure the PIN in the UPRIGHT inserts into the å hole in the BRACE. BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Maximum Arrow Surface with 210 degrees HIDDEN CAMS Rounded edge Minimum 190 degrees Page 12 414468 www.sauder.com/services...
Page 13
Step 8 Fasten the SHELF (G) to the UPRIGHT (C). Tighten two å HIDDEN CAMS. Rounded edge Maximum Arrow 210 degrees Minimum 190 degrees www.sauder.com/services 414468 Page 13...
Page 14
NOTE: Be sure the PIN in the BRACE inserts into the hole å in the END. S u r f a c H I D D E N i t h o Edge with CAM DOWELS Maximum Arrow 210 degrees Minimum 190 degrees Page 14 414468 www.sauder.com/services...
Page 15
Step 10 Fasten the BOTTOM (E) to the RIGHT END (A) and å UPRIGHT (C). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Rounded edge www.sauder.com/services 414468 Page 15...
Insert a METAL PIN (1R) into the holes in the FEET (R and S). å Push the PINS in the FEET into the holes in the SKIRTS. å BLACK 9/16" LARGE HEAD SCREW (8 used for the METAL BRACKETS) Page 16 414468 www.sauder.com/services...
Page 17
Fasten the CORNER BRACKETS (31G) to the BOTTOM (E), å SIDE SKIRTS (M), and FEET (R and S). Use twenty-four BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (28 used for the METAL BRACKETS) www.sauder.com/services 414468 Page 17...
Page 18
BACK fastened. The unit may collapse. Push on opposite corners of your unit if needed to make it "square". Fasten the BACK (H) to your unit using the NAILS (1N). å NAIL (22 used in this step) Page 18 414468 www.sauder.com/services...
Finished surface Short fi nished edge BLACK 1-1/4" FLAT HEAD SCREW (2 used in this step) These holes must be facing up. Short fi nished edge BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) www.sauder.com/services 414468 Page 19...
Page 20
Fasten the HINGES (12H) to the PENCIL DRAWER å BOTTOM (Q). Use two SILVER 9/16" LARGE HEAD SCREWS (54S). SILVER 9/16" LARGE HEAD SCREW SILVER 5/8" FLAT HEAD SCREW (2 used in this step) (4 used in this step) Page 20 414468 www.sauder.com/services...
Page 21
Fasten a KNOB (48K) to the PENCIL DRAWER å FRONT (N). Use a BLACK 1-1/8" MACHINE SCREW (21S). Roller end BLACK 1-1/8" MACHINE SCREW (1 used for the KNOB) Roller end BROWN 1" FLAT HEAD SCREW (4 used for the SLIDES) www.sauder.com/services 414468 Page 21...
DRAWER SIDES (D14 and D15). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). NOTE: Be sure the DRAWER BOTTOM (D716) inserts into å the groove of the LARGE DRAWER BACK (D78). Repeat steps 1 through 3 for the small drawer. å Page 22 414468 www.sauder.com/services...
Page 23
BLACK 1-1/8" MACHINE SCREW (2 used for the KNOBS) Roller end Screw head - turn CAM to line up holes in SLIDES with holes in DRAWER SIDES. Roller end GOLD 5/16" FLAT HEAD SCREW (8 used for the SLIDES) www.sauder.com/services 414468 Page 23...
Page 24
Step 19 Push the FILE GLIDES (4B) onto the top edge of the å LARGE DRAWER SIDES (D14 and D15). Page 24 414468 www.sauder.com/services...
Page 25
Lift the front of the drawer up and slide it into the unit. Repeat this step to insert the small drawer and pencil drawer. 60 lbs. 20 lbs. 15 lbs. 30 lbs. 30 lbs. (4 used) To cover HIDDEN CAMS www.sauder.com/services 414468 Page 25...
#4. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. Page 26 414468 www.sauder.com/services...
EXTRÉMITÉ DROITE ..........1 40CA ÉLÉMENT DROITE............2 pour future référence. 40CB ÉLÉMENT GAUCHE ..........2 EXTRÉMITÉ GAUCHE ..........1 Pour contacter Sauder 40CC TIROIR DROIT ..............2 MONTANT................1 en ce qui concerne cet 40CD TIROIR GAUCHE ............2 DESSUS ................1 élément, faire référence GLISSIÈRE DROITE D'ÉLÉMENT .....1...
Page 28
Fixer les SUPPORTS EN CORNIÈRE (31G) au DESSOUS (E), aux PLINTHES LATÉRALES (M) et aux PIEDS (R et S). Utiliser vingt-quatre VIS TÊTE Fixer le VOILE DE FOND (F) à l'EXTRÉMITÉ GAUCHE (B). Serrer trois LARGE 14 mm NOIRES (1S). EXCENTRIQUES ESCAMOTABLES. Page 28 414468 www.sauder.com/services...
Page 29
GRAND TIROIR (D14 et D15). Utiliser quatre VIS TÊTE PLATE 40 mm NOIRES (30S). REMARQUE : S'assurer que le FOND DE TIROIR (D716) s'encastre dans la rainure de l'ARRIÈRE DE GRAND TIROIR (D78). Répéter les étapes 1 à 3 pour le petit tiroir. www.sauder.com/services 414468 Page 29...
RIEL IZQUIERDO DE GABINETE ......1 pour future référence. PARAL ..................1 CORREDERA DERECHA DE CAJÓN ....1 Pour contacter Sauder PANEL SUPERIOR ............1 CORREDERA IZQUIERDA DE CAJÓN ....1 en ce qui concerne cet D14 LADO DERECHO DE CAJÓN GRANDE ..1 10A EXCÉNTRICO DE CORREDERA ......4...
Page 31
LATERALES (M) y a las PATAS (R y S). Utilice veinticuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). PASO 6 Fije el VELO DE FONDO (F) al EXTREMO IZQUIERDO (B). Apriete tres EXCÉNTRICOS ESCONDIDOS. www.sauder.com/services 414468 Page 31...
Page 32
NOTA: Por favor, lea las páginas de atrás del folleto de instrucciones en cuanto a importante información de seguridad. Esto completa el ensamblaje. Para limpiar la unidad, humedezca un paño con agua de llave y limpie. Page 32 414468 www.sauder.com/services...
Page 33
à Les téléviseurs peuvent être particulièrement un téléviseur. cet eff et. lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/services 414468 Page 33...
Page 34
Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 34 414468 www.sauder.com/services...
Page 35
GARANTIE LIMITÉE DE 5 ANS 1. Sauder Woodworking Co. (Sauder®) off re une couverture de garantie limitée à l’ a cheteur 4. La présente garantie ne s’ a pplique qu’ a ux défauts garantis qui se produisent pour initial du présent produit pendant une période de cinq ans à...
Page 36
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.
Need help?
Do you have a question about the Camarin Series and is the answer not in the manual?
Questions and answers