Preparation For Use - Symphonic ST414FG Owner's Manual

PREPARATION FOR USE

CONNECTIONS
Plug the incoming cable into the ANT. IN jack on the rear of the TV.
Cable
Antenna
OR
TV signal
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Cable Box or
Satellite Box*
OR
IN
Incoming cable from Cable
Company or Satellite Antenna
Cables not included
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU'AU FOND.
Note:
•
For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT. IN jack before moving the unit.
[EXTERNAL CONNECTION]
Front AUDIO/VIDEO input
ex.
Video Camera Video Game
INSTALLING THE BATTERIES
1 2
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
INITIAL SETUP
When you turn on the power for the first time, the "SELECT LANGUAGE" menu is displayed.
The "INITIAL SETUP" menu is displayed every time you turn on the unit unless the scanning is
completed.
1
1
Select the desired
SELECT LANGUAGE
language according to
ENGLISH
NEXT:PRESS CH K
the screen indication.
ESPAÑOL
DESPUÉS:PRESIONE CH L
After that, the TV
FRANÇAIS
APRÈS:PRESSEZ VOL K
performs "AUTO
PRESET CH" to scan
channels available for
– INITIAL SETUP –
the broadcasting in PLEASE CONNECT ANTENNA
OR CABLE OR SATELLITE
TO THIS UNIT.
your area.
THEN PRESS CH K ,
IN ORDER TO PERFORM
"AUTO PRESET CH".
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the
tuner stops on the lowest memorized channel.
Notes:
In case no channel can be received by the channel scanning, "NO TV SIGNALS" is displayed on
●
the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
If those settings do not work properly, please call our help line on the front page of this owner's manual.
●
SELECTING AUDIO/VIDEO INPUT SELECTING AUDIO/VIDEO INPUT
You can select external input jacks by pressing [GAME] on the remote control. You can select external input jacks by pressing [GAME] on the remote control.
1 1
To use external input
GAME
Picture: GAME (ON)
Input: External
In the Game mode, you can use front input jacks with suitable picture adjustments for video games.
Notes:
If you press [GAME] when the TV is off, the TV turns on and enters in Game mode.
●
If you adjust another picture control while in Game mode, this mode will automatically
●
be canceled.
Rear of this TV
ANT . IN
OU T
ANT. IN
*Note (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
Front of this TV
VIDEO
Video Cable
(OUT)
(IN)
(OUT)
(IN)
Audio Cable
3 Install two AA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote con-
trol.
2 2
If the TV screen shows
snow noise and there
is no operation for
more than 10 seconds,
"HELPFUL HINTS"
appears. Follow the
instructions listed on
the screen.
2
2
To return to TV channel
GAME
GAME
You can enter into Video mode from Game mode by adjusting a Picture control.
1
1
To use external input
GAME
OPERATIONS
REMOTE CONTROL AND FRONT PANEL FUNCTION
To send infrared ray (IR) signal
AUDIO
Channel number buttons
Press two digits to directly access the
desired channel. Remember to press
a "0" before a single digit channel.
CH(ANNEL) K K / L L buttons
To select channels and move
up/down through menu items
To view on-screen menu
Note:
You can test if the remote control sends out the infrared signal with an AM radio.
●
(Refer to "TROUBLESHOOTING GUIDE".)
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF
THE ANTENNA/CABLE/
SATELLITE IS PROPERLY
CONNECTED.
2. DID YOU PERFORM
"AUTO PRESET CH" ?
3. PLEASE REFER TO FRONT
PAGE OF THE OWNER'S
MANUAL OR REAR PANEL
FOR SUPPORT LINE
INFORMATION.
VIDEO AUDIO
VIDEO input jack
15
Note:
If some digits appear in the corner of the screen when the unit is turned on for the first time,
●
press [POWER] without unplugging the power cord.
2
2
GAME
Select "PICTURE"
Picture: GAME (ON)
Input: External
After 10 seconds
3
3
IR transmitter
POWER button
POWER GAME
To turn TV on/off
DISPLAY
1 2 3
4 5 6
CHANNEL
RETURN
7 8 9
0 +100
CH
VOL VOL
CH
MENU
MENU button
VIDEO AUDIO EARPHONE MENU VOLUME CHANNEL POWER
EARPHONE MENU VOLUME CHANNEL
CHANNEL ▲/▼ buttons
To select channels
X X / Y Y
VOLUME
To adjust volume
MENU button
To view on-screen menu
EARPHONE jack
AUDIO input jack
To cancel Game mode only
MENU
[-]
GAME MODE
VOL
OFF
VIDEO
Picture: Customized
Input: External
To return to TV channel
GAME
2 times
GAME button
Press to set the Game mode
SLEEP
SLEEP button
To set Sleep Timer
DISPLAY button
To display CH No./Audio Status
CHANNEL RETURN button
To return previous screen
MUTE
MUTE button
To mute sound
VOL(UME) K K / L L buttons
To adjust volume
To decide the command of settings
POWER
Infrared Sensor Window
POWER button
To turn TV on/off
buttons
[+]
ON
15