Advertisement
MSA Latchways
LadderLatch, TowerLatch, TowerLatch SP and Climblatch
EN 353-1:2002 & CNB/P/11.073 and EN 353-1:2014 /prA1:2017.
Part number / identification of device type
Important
Carefully read all of the safety and user instructions before using this product; paying particular attention to all
sections of these user instructions that carry warning symbols and notices.
Warning symbol. This symbol is used throughout the instructions whenever there is a risk of
personal injury or death to either the installer or end user of the product. Ensure that these warnings
are read and understood and followed at all times.
Caution symbol. This symbol is used throughout the instructions whenever there is a risk of
damaging the Latchways product. Ensure that these cautions are read and understood and followed
at all times.
Mandatory symbol. This symbol is used throughout the instructions whenever there is a specific
instruction for Latchways product. Ensure that these important instructions are read and understood
and followed at all times.
Document number
Verti_96
Verti_96
Latchways, an MSA Company.
®
Vertical Device
Vertical fall arrest device to
Issue number
9
10
Change request
100123
100223
Date of issue
13/1/2017
07/07/2017
1
Advertisement
Table of Contents
Related Manuals for Latchways Latchways LadderLatch
Summary of Contents for Latchways Latchways LadderLatch
- Page 1 Caution symbol. This symbol is used throughout the instructions whenever there is a risk of damaging the Latchways product. Ensure that these cautions are read and understood and followed at all times.
- Page 2 TowerLatch SP Device (see section 1.7) 3100L-00T LadderLatch Device 3100L-00AC LadderLatch AC Device 3102L-00 TowerLatch Device 3102L-00AC TowerLatch AC Device 3103L-00 LadderLatch Device (Canada) 3104L-00 LadderLatch Device (USA) 3105L-00 TowerLatch Device (USA) Webbing strop Additional cover LadderLatch AC Type Devices TowerLatch Latchways, an MSA Company.
-
Page 3: Table Of Contents
Requirements for use. Before use checks. User instructions. Materials. Disposal Inspection, maintenance and storage. Markings. Product Card. EC Declaration of Conformity. Appendix 1 - ClimbLatch Installer company details Company Name Company Address Contact Name Tel No Email Latchways, an MSA Company. -
Page 4: Safety Instructions
When using the Latchways vertical device, basic on site safety precautions, including the following, should be observed to ensure personal safety. All Users of the Latchways vertical devices shall be trained and competent in its safe use and shall read and follow these instructions. Retain these instructions for future reference. - Page 5 The Latchways devices have been subjected to an additional series of tests devised by TUV/NEL (Notified Body no. 0320). These tests were conducted using 71 kg (156 lbs) and 100 kg (220 lbs) anthropomorphic test dummies with different body postures (reference NEL certificate no.
- Page 6 The device is only to be used to provide an attachment for one User to a Latchways vertical cable system. All system components shall be manufactured and specified by Latchways plc.
-
Page 7: Product Specification
LadderLatch, TowerLatch, TowerLatch SP and Climblatch 2. Product specification The device is designed to arrest the fall of one climber in conjunction with a Latchways vertical fall arrest system. If a climber were to fall whilst connected to the Latchways system the energy absorber will deploy and reduce the load applied to the body to 6 kN (1,350 lbf) or less. -
Page 8: Required Equipment
Before undertaking work at height and at regular intervals during the period of work, a risk assessment shall be carried out. The Latchways vertical GTFA device shall be directly attached to the front chest position of a full body harness when used on a vertical system All users must ensure that a minimum distance of 3 m (9‘10”) is maintained between the head of each user and... - Page 9 If a fault is identified with system tension the system shall not be used and the issue raised with site supervision. Latchways, an MSA Company.
- Page 10 Ensure the device is within its service date. If the Latchways vertical GTFA device fails any of the above criteria it shall be withdrawn from service and returned to Latchways plc. If the Latchways vertical GTFA device is damaged, there is any doubt about the safe condition of the device or the service date has expired it shall be withdrawn from service.
-
Page 11: User Instructions
Press the release catch with your right thumb. The release catch will not operate if the device is incorrectly oriented. Using your left hand pull the Star wheel away from the body of the device and offer the device up to the cable. Fig 6.3. Cable Pull Star wheel Depress Release Catch Fig 6.3. Latchways, an MSA Company. -
Page 12: Materials
If this does not happen, remove the device from service and do not use until the device has been recertified by a Latchways authorised agent. When ascending and descending, the device shall always be below the harness chest attachment point. -
Page 13: Inspection, Maintenance And Storage
This is subject to passing periodic examinations. Cleaning – As part of general maintenance the Latchways vertical GTFA device may require cleaning from time to time this may be done using warm water and a domestic detergent. The device should be thoroughly rinsed and dried naturally away from direct heat. - Page 14 Apply WD40 between the Cam and each of the side plates. Storage - The Latchways vertical GTFA device should be stored away from excessive heat, high humidity, sharp edges, corrosives or other foreseeable causes of damage. The equipment should be protected from unnecessary stress, pressure or rough handling.
-
Page 15: Markings
® MSA Latchways Vertical Device LadderLatch, TowerLatch, TowerLatch SP and Climblatch 10. Markings The following markings are shown on the Latchways LadderLatch device Read these instructions before use Use this way up only For illustrative purposes only: Example shown is model 3100L-00 for BS EN 353-1:2002 jurisdictional regions. -
Page 16: Product Card
This card should be filled in on receipt of the device and on receipt after every service. Equipment Record Product : LadderLatch Device conforms to BS EN 353-1 2002 / CSA Z259.2.1 / ANSI Z359.1-2007 & AS/NZS 1981.3-1997 Model & Trade name : Latchways Serial Number : Type/Identification : LadderLatch device Tel: +44 (0)1380 732700... -
Page 17: Ec Declaration Of Conformity
Article 11 point B of Directive 89/686/EEC under the supervision of the notified body:- INSPEC International Limited (Notified Body No: 0194) 56 Leslie Hough Way, Salford, Greater Manchester, M6 6AJ, England June 2012 T. Bissett Technical Manager Latchways, an MSA Company. - Page 18 Under no circumstances must the device be used the other way around. User Instructions On a vertical system - connect the Latchways ClimbLatch device via the karabiner to the chest attachment point of the harness. Entry to the system is identical whether for a vertical, inclined or horizontal system. Hold the cam link in the position shown in Fig1.
- Page 19 Once the ClimbLatch device is fully engaged with the tube pull the device along until the gap has been cleared. Next tighten up the thimble on the entry gate to secure the system. Fig 3. Fig 3 System set up is now complete. Latchways, an MSA Company.