Ma5600 Is Not Showing Alarms On Imanager N2000 Bms - Huawei MA5600 Manual

MSAN UA5000 Cases
Views: 8
Author: Vikas chaudhary
Product Family: Broadband Access
Fault Type: Host/Network Management System (independent from service)
Keywords: MA5600 is not showing alarms on imanager N2000 BMS
Permission Level: 03Equipment Users Permission
Phenomenon Desc
MA5600 version-V2
ription:
Imanager N2000 BMS version-V2
MA5600 is not showing any alarm on Imanager N2000 BMS.
If some Fault occur on MA5600 ,it is not get noticed on Imanager N2000 BMS.
Alarm Informatio
There was a red LED(alarm) glowing on the controller card of MA5600.
n:
Cause Analysis: There is a red LED(alarm) glowing on the controller card of MA5600 but there was no indication of this alarm on imanager
When i manually generate some alarm on MA5600 example pull out one of the controller card,then also there was no alarm
configuration of SNMP trap source on MA5600 ---->>
ADN-DLM-960-M-01 (config)# snmp-agent community read public
ADN-DLM-960-M-01 (config)# snmp-agent community write private
ADN-DLM-960-M-01 (config)# snmp-agent sys-info version v1 v2c
ADN-DLM-960-M-01 (config)# snmp-agent target-host trap address 172.16.2.183 securityname Huawei
ADN-DLM-960-M-01 (config)#snmp-agent trap enable standard
ADN-DLM-960-M-01 (config)#snmp-agent trap source Meth0
Problem solving procedure:
1. SNMP-agent traget-host trap adress should be floating ip in case of two ip adress of server. I have changed snmp-agent
2. I have changed snmp-agent trap source Meth0 to Management Vlan,i.e replace Meth0 by Management vlan of MA5600.
3.On imanager N2000 BMS go to fault setting and make auto sink to be on.
Handling Proces
There is a red LED(alarm) glowing on the controller card of MA5600 but there was no indication of this alarm on imanager
s:
When i manually generate some alarm on MA5600 example pull out one of the controller card,then also there was no alarm
configuration of SNMP trap source on MA5600 ---->>
ADN-DLM-960-M-01 (config)# snmp-agent community read public
ADN-DLM-960-M-01 (config)# snmp-agent community write private
ADN-DLM-960-M-01 (config)# snmp-agent sys-info version v1 v2c
ADN-DLM-960-M-01 (config)# snmp-agent target-host trap address 172.16.2.183 securityname Huawei
ADN-DLM-960-M-01 (config)#snmp-agent trap enable standard
ADN-DLM-960-M-01 (config)#snmp-agent trap source Meth0
Problem solving procedure:
1. SNMP-agent traget-host trap adress should be floating ip in case of two ip adress of server. I have changed snmp-agent
2. I have changed snmp-agent trap source Meth0 to Management Vlan,i.e replace Meth0 by Management vlan of MA5600.
3.On imanager N2000 BMS go to fault setting and make auto sink to be on.
problem is resolved and we can see the alarm of MA5600 on imanager N2000 BMS.
Suggestions and
1.SNMP agent trap source should be management vlan on MA5600.
Summary:
2. SNMP-agent-trap-host trap adress should be floating ip.
3.On Imanager N2000 BMS auto sink should be on.
Confidential Information of Huawei. No Spreading without Permission
Chapter 1 MA5600 Cases
Product: SmartAX MA5600
13