Advertisement
Quick Links
Technical Data and Layout Planner
Due to continual updating, design and specifications are
subject to change without notice.
PA-15589
Rev. 2/18
400 Material Mover
Copyright ©2001-2018 Patz Corporation
PRINTED IN U.S.A.
Patz Corporation
P.O. Box 7
Pound, WI 54161
T
: (920) 897-2251
el
F
: (920) 897-2142
ax
info@patzcorp.com
www.patzcorp.com
Advertisement
Related Manuals for Patz Corporation 400 Material Mover
Summary of Contents for Patz Corporation 400 Material Mover
- Page 1 400 Material Mover Technical Data and Layout Planner Patz Corporation P.O. Box 7 Due to continual updating, design and specifications are Pound, WI 54161 subject to change without notice. : (920) 897-2251 : (920) 897-2142 info@patzcorp.com PA-15589 Rev. 2/18 Copyright ©2001-2018 Patz Corporation PRINTED IN U.S.A.
- Page 2 3) Refer to Volume Capacity Table for material delivery rate at an estimated depth in trough. U.S. UNITS METRIC UNITS M-400 Material Mover, moves 15 ton/hour, wood chips at M-400 Material Mover, moves 13.61 t/hr, wood chips at 30 lbs/cu. ft.
-
Page 3: Typical Installations
Typical Installations It is the user’s responsibility to cover all walkways and return troughs with a steel floor plate to prevent possi- ble personal injury. Cover should extend from hold down post at bottom end of the elevating slide to and includ- ing return corner. - Page 4 Typical Installations (Con’t) NOTE: The shaded portions indicate where the troughs can be loaded. #1 L.H. CONCRETE TROUGHS WITH STEEL LINERS (ELIMINATES RETURN CORNER). FOR DRY MATERIAL - USE RETURN CORNER WITH UHMW SHOE. #3 L.H. CONCRETE TROUGHS WITH STEEL LINERS AND 90° RETURN CORNER.
- Page 5 Typical Trough Cross Sections Above Floor LOADED SIDE OR EMPTY RETURN In Floor LOADED LOADED LOADED LOADED SIDE SIDE SIDE SIDE OR EMPTY OR EMPTY OR EMPTY OR EMPTY RETURN RETURN RETURN RETURN SIDE SIDE SIDE SIDE NOTE: Unlined concrete troughs can produce added friction, resulting in increased horsepower requirements, increased wear of the flites, as well as wearing away of the concrete.
- Page 6 Dimensions SINGLE TROUGH, STEEL, SLANTED 60° AND 90° STRAIGHT SIDEWALL BOLT-TOGETHER SECTIONS Single Trough, 52-1/2 Straight Pull (1334 mm) (Right Hand) 46-1/2 (1181 mm) 52-1/2 (1334 mm) 53-3/8 60° Single Trough (1356 mm) 48 90° Slanted 60° 26-7/8 (1219 mm) (683 mm) 46-1/2 Sidewall 28-1/2 24-7/8 (1181 mm) (724 mm) (632 mm) (End View) 70-1/2 12-7/8 11-1/2 (1791 mm) (327 mm) (292 mm)
- Page 7 Dimensions DOUBLE TROUGH, STEEL, SLANTED 60° SIDEWALL BOLT-TOGETHER SECTIONS 203, HVY. & XH REDUCER DRIVE UNIT & FRONT SLIDE (8 FT. SHOWN) ALL COMPONENTS: 18” (457) TROUGH WIDTH DIMENSIONS: INCHES (MM) 7° ELBOW SECTION REAR SLIDE 22.5° SL. CORNER SECTION PLANETARY DRIVE UNIT & FRONT HOLD DOWN POST SECTION WITH SHOE (NOT SHOWN IN LAYOUT) SLIDE (8 FT. SHOWN) AND RETURN GUIDE TRAPDOOR SECTION COVER ASSEMBLY 90°...
- Page 8 Dimensions DOUBLE TROUGH, STEEL, 90° STRAIGHT SIDEWALL BOLT-TOGETHER SECTIONS 203, HVY. & XH REDUCER DRIVE UNIT & FRONT SLIDE (8 FT. SHOWN) ALL COMPONENTS: 18” (457) TROUGH DIMENSIONS: INCHES (MM) 7° ELBOW SECTION REAR SLIDE PLANETARY DRIVE UNIT & FRONT HOLD DOWN POST SECTION WITH SHOE 22.5° SL. CORNER SECTION SLIDE (8 FT. SHOWN) (NOT SHOWN IN LAYOUT) AND RETURN GUIDE TRAPDOOR SECTION...
- Page 9 Patz Corporation, P.O. Box 7, Pound, WI 54161-0007 Phone: 920-897-2251 Fax: 920-897-2142 info@patzcorp.com www.patzcorp.com Copyright ©2001-2017 Patz Corporation...
Need help?
Do you have a question about the 400 Material Mover and is the answer not in the manual?
Questions and answers