BROOKING INDUSTRIES HORIZON Manual

 WIRING
SINGLE / DUAL COLOR
RED
to +VDC with rated fuse
(for correct fuse, refer to Fuse Rating chart)
BLACK
to Chassis ground
ORANGE
[+] Rear "Left Arrow"
BLUE
[+] Rear "Right Arrow"
[+] Warning Mode 2
or
GREEN
[+] End-Flasher
BROWN [+] Warning Mode 1 [
YELLOW [+] Flash Pattern Selection /
[ ] Control Panel Indicator Signal out /
NOTE:
= Precedence order, when more than 1 wire is activated at the same
[Px]
time, higher precedence wire will affect lower precedence wire. P1 being
the highest priority.
POWER WIRES
1. Route Power Wires to the vehicle firewall towards the battery and follow the
factory wiring harness through the firewall. If drilling a hole is required, ensure
that no component is damaged from the drilling.
2. Install a fuse (user-supplied) to the end of the
battery. (for correct fuse, refer to Fuse Rating chart)
3. Connect the BLACK wire to the factory chassis ground next to the battery.
NOTE: Ensure that all wires of the power cable are securely connected to the power
source.
CONTROL WIRES
1. Route Control Wires towards the dash area to a switch panel (user-supplied).
2. Connect the required wires to a controller (switch panel) or power source.
TRAFFIC ARROW
1. Activate Traffic Arrow function by applying
■ ORANGE wire for Left Arrow.
■ BLUE
wire for Right Arrow.
■ Above 2 wires together for Center-Out.
NOTE: If the stick is equipped with Dual Color lightheads,Traffic Arrow will display
in Color 2.
2. To change the Traffic Arrow flash pattern, tap
a. quickly 1 time to next pattern. (refer to Traffic Arrow Patterns chart).
b. quickly 3 times to revert back to Traffic Arrow Pattern #1.
WARNING MODE 1 and MODE 2
Each Warning Mode is capable of storing / saving one flash pattern.
To change the flash pattern:
1. Activate a warning Mode by applying
■ BROWN wire for Warning Mode 1.
■ GREEN wire for Warning Mode 2.
2. Once a warning mode is activated, tap
a. quick 1 time to next pattern (refer to Flash Pattern chart).
b. quickly 3 times to revert back to Pattern #1.
To set color mode (for Dual Color Models only):
1. Disconnect all power, then apply
RED wire together for 3 seconds to enter color setting mode; the stick will
display the current color mode for the activated warning mode.
2. Tap +VDC to wire to scroll through the color modes:
a. Single Color 1 b. Single Color 2
3. Save and exit color setting by disconnecting all power.
LOW POWER OPERATION (DIM FUNCTION)
Activate dimming function by continuously applying
CONTROL PANEL SIGNAL INDICATOR
Connect WHITE wire to the display signal input of a compatible Control Panel to
display current lighthead activity.
HORIZON
HORIZON
Traffic Advisor / Warning Stick Manual
Traffic Advisor / Warning Stick Manual
No. of
Lightheads
6-Head
8-Head
10-Head
[P2]
Rear "Center Out Arrow"
[P2]
[P3]
(See "FIRMWARE SELECTION" for End-Flasher Mode)
P4]
[+] Low Power Operation
[+] Programming
RED wire, and connect it to the
+VDC to:
+VDC YELLOW
to
+VDC to BROWN, or GREEN
+VDC to YELLOW wire:
+VDC to BROWN (or GREEN),
c. Dual Color 1&2 d. Dual Color 2&1
+VDC to YELLOW
Fuse Rating
1 Random/Custom (see "PROGRAMMING")
12VDC 24VDC
Model Model
2 All
3 All
5.0A 3.0A
4 All
7.5A 4.0A
10.0A 5.0A 5 All
6 All
7 All
8 All
9 All
[P1]
10 All
11 All
12 All
13 All
14 Left-Right
15 Left-Right
16 Left-Right
17 Left-Right
18 Side-by-Side
19 Side-by-Side
20 Side-by-Side
21 Side-by-Side
22 Outside-in
23 Outside-in
24 Outside-in
25 Outside-in
26 All
27 Split
28 Left-Right
29 Left-Right
30 Left-Right
31 Left-Right
32 Left-Right
33 Left-Right
34 Left-Right
35 Left-Right
36 Left-Right
37 Left-Right
38 Left-Right
39 Side-by-Side
40 Side-by-Side
41 Side-by-Side
42 Side-by-Side
43 Composite
44 Side-by-Side
45 Composite
46 Composite
47 Composite
48 Composite
49 Composite
wire:
50 Composite
For dual color models:
SC = Single Color Mode; SC/DC = Single or Dual Color Mode
# Actual ECE R65 approval is based on the p/n ordered.
* Patterns show full effect in dual color mode.
1 Sweep Single
2 Sweep Double
wire.
3 Sweep Triple
4 Sweep 1 End x2
5 Solid
6 Solid End x2
7 Solid Chaser
8 Solid Fade
9 Blink Double
10 Blink Triple
11 Blink Solid
23 Sweep Single w/ Dual End Flasher
and
24 Sweep Single w/ Dual End Flasher
25 Solid Chaser Dual Quick
26 Solid Chaser D
27 Solid Chaser Dual Slow
Single color model: Patterns 1~11 are available
Dual color model: C1 = Color 1; C2 = Color 2; C1&2 = Color 1&2
1 Double
2 Quad
wire.
3 Single
4 Double
5 Quad
6 Single
# Actual ECE R65 approval is based on the p/n ordered.
-1-
Warning Patterns
SC
#
Double [R65] SC
Single [2HZ] SC
Triple [2HZ] SC
Quad [2HZ] SC
Steady / Scene SC
Single [SAE, CA13] SC
Double [SAE] SC
Mega SC
Ultra [SAE] SC
Single-Quad SC
Single H/L SC
Single-Triple-Quint SC
Single SC
Double SC
Mega SC
Ultra SC
Single SC
Double SC
Mega SC
Ultra SC
Single SC
Double SC
Mega SC
Ultra SC
Scan SC
Scan SC
Single Mid SC/DC
Double-Single SC/DC
Triple-Single SC/DC
Quad-Single SC/DC
SC/DC
Single H/L II
Double-Blast SC/DC
Swing I SC/DC
Triple-Blast SC/DC
Swing II SC/DC
Swing III SC/DC
Triple H/L SC/DC
Single Fast SC/DC
Quad Fast SC/DC
Double Fast SC/DC
Quad-Double SC/DC
SC/DC
Quad-Scan-Blast
*
Mega X SC/DC
All Scan-Split Scan SC/DC
Triple-Scan SC/DC
Single-Scan-Blast SC/DC
Solid Scan * SC/DC
*
Solid Scan-Mega SC/DC
*
Solid Scan-Blast SC/DC
Traffic Arrow Patterns
C2 12 Sweep Single
C2 13 Sweep Double
C2 14 Sweep Triple
C2 15 Sweep 1 End x2
C2 16 Solid
C2 17 Solid End x2
C2 18 Solid Chaser
C2 19 Solid Fade
C2 20 Blink Double
C2 21 Blink Triple
C2 22 Blink Solid
[2HZ] C1&2
[SAE] C1&2
C1&2
C1&2
C1&2
End Flasher Patterns
[R65] # (All) 7 Double [2HZ] (Left Right)
[2HZ] (All) 8 Quad [2HZ] (Left Right)
[2HZ] (All) 9 Single [2HZ] (Left Right)
[SAE] (All) 10 Double [SAE] (Left Right)
[SAE] (All) 11 Quad [SAE] (Left Right)
[SAE] (All) 12 Single [SAE] (Left Right)
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1