BROOKING INDUSTRIES HORIZON Manual

Warning stick

Advertisement

 WIRING
SINGLE / DUAL COLOR
RED
to +VDC with rated fuse
(for correct fuse, refer to Fuse Rating chart)
BLACK
to Chassis ground
[+]
GREEN
[+]
BROWN
YELLOW
[+]
= Precedence order, when more than (1) wire is activated at the same
NOTE:
[Px]
time, the higher precedence wire will affect lower precedence wire. P1
being the highest priority.
POWER WIRES
1. Route Power Wires to the vehicle firewall towards the battery and follow the
factory wiring harness through the firewall. If drilling a hole is required, ensure
that no component is damaged from the drilling.
2. Install a fuse (user-supplied) to the end of the
battery. (for correct fuse, refer to Fuse Rating chart)
3. Connect the BLACK wire to the factory chassis ground next to the battery.
NOTE: Ensure that all wires of the power cable are securely connected to the power
source.
CONTROL WIRES
1. Route Control Wires towards the dash area to a switch panel (user-supplied).
2. Connect the required wires to the switch panel or power source.

WARNING MODE 1 and MODE 2

Each warning mode is capable of storing / saving one pattern.
To change the flash pattern:
1. Activate the desired Warning Mode by applying
BROWN
wire for Warning Mode 1.
GREEN
wire for Warning Mode 2
2. Let the warning mode run for at least 3 seconds then:
a. tap
YELLOW
wire to
b. tap
YELLOW
wire to

COLOR MODE SETTING (available w/ dual color models only):

1. Disconnect all power, then apply
RED
wire together for at least 3 seconds to enter color setting; the stick will display
the current color mode for the activated warning mode.
2. Tap
+VDC
to
YELLOW
a. Color 1
b. Color 2
c. Color 1&2 Alternating flash
d. Color 2&1 Alternating flash
3. Save and exit color setting mode by disconnecting all power.

LOW POWER / DIMMING MODE

Activate dimming function by continuously applying
Warning Mode 2
[P1]
Warning Mode 1
[P2]
Flash Pattern Selection / Synchronization
Connect
YELLOW
wires of all sticks together for synchronization
(All sticks should be set to the same pattern)
Low Power Operation
[+]
RED
+VDC
+VDC
scroll through warning patterns.
+VDC
quickly 3
to revert back to flash pattern #1.
+VDC
to
BROWN
wire to scroll through the color mode:
+VDC
HORIZON
Fuse Rating
No. of
12VDC
24VDC
Lightheads
Model
Model
2-Head
2.0A
1.0A
4-Head
4.0A
2.0A
wire, and connect it to the
to BROWN, or
GREEN
wire.
(or GREEN),
YELLOW
and
to
WHITE
wire.
-1-
Warning Stick Manual
Warning Patterns
1
Random
2
All
Double [R65]
Single [2HZ]
3
All
4
All
Triple
[2HZ]
5
All
Quad
[2HZ]
6
All
Steady / Scene
Single [SAE, CA13]
7
All
Double [SAE]
8
All
Mega
9
All
Ultra
[SAE]
10
All
Single-Quad
11
All
Single H/L
12
All
Single-Triple-Quint
13
All
Single
14
Left Right
Double
15
Left Right
Mega
16
Left Right
Ultra
17
Left Right
Single
18
Side-by-Side
Double
19
Side-by-Side
Mega
20
Side-by-Side
Ultra
21
Side-by-Side
Single
22
Outside-in
Double
23
Outside-in
Mega
24
Outside-in
Ultra
25
Outside-in
Scan
26
All
Scan
27
Split
Single Mid
28
Left Right
Double-Single
29
Left Right
Triple-Single
30
Left Right
Quad-Single
31
Left Right
Single H/L II
32
Left Right
Double-Blast
33
Left Right
Swing I
34
Left Right
Triple-Blast
35
Left Right
Swing II
36
Left Right
Swing III
37
Left Right
Triple H/L
38
Left Right
Single Fast
39
Side-by-Side
Quad Fast
40
Side-by-Side
Double Fast
41
Side-by-Side
Quad-Double
42
Side-by-Side
Quad-Scan-Blast
43
Composit
Mega X
*
44
Side-by-Side
All Scan-Split Scan
45
Composite
Triple-Scan
46
Composite
Single-Scan-Blast
47
Composite
Solid Scan
*
48
Composite
Solid Scan-Mega
49
Composite
50
Composite
Solid Scan-Blast
# Actual ECE R65 approval is based on the p/n ordered.
* Patterns show full effect in dual color mode.
For dual color models:
SC = Single Color Mode; SC/DC = Single or Dual Color Mode
SC
#
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
SC/DC
*
SC/DC
*
SC/DC

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HORIZON and is the answer not in the manual?

Questions and answers

Summary of Contents for BROOKING INDUSTRIES HORIZON

  • Page 1 HORIZON Warning Stick Manual  WIRING Fuse Rating Warning Patterns SINGLE / DUAL COLOR No. of 12VDC 24VDC Random Lightheads Model Model Double [R65] to +VDC with rated fuse 2-Head 2.0A 1.0A Single [2HZ] (for correct fuse, refer to Fuse Rating chart) 4-Head 4.0A...
  • Page 2  FIRMWARE SELECTION All units are pre-set to the firmware of its number of lightheads. To change firmware: 1. Applying +VDC YELLOW wires simultaneously for more than 3 seconds to enter FIRMWARE selection. 2. Once in FIRMWARE selection mode, the unit will display one of the following patterns. 2-Head Warning Stick steady 4-Head Warning Stick...

Table of Contents