Acuity AEL VALIANT Series Installation Instructions

INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP LED VERSION
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
!
CUPOLA LENS CUPOLA LENS
ADJUST PHOTOCONTROL ADJUST PHOTOCONTROL
BY LIFTING & TURNING BY LIFTING & TURNING
CUPOLA SIMULTANEOUSLY CUPOLA SIMULTANEOUSLY
HOOD HOOD
TRIGGER TRIGGER
LATCH (2) LATCH (2)
-OPTIONAL- -OPTIONAL-
LENS LENS
PANELS (4) PANELS (4)
LADDER REST (2) LADDER REST (2)
-OPTIONAL- -OPTIONAL-
SET SCREWS (3) SET SCREWS (3)
FIGURE 1 FIGURE 1
CLOSED HOOD - STREET SIDE VIEW CLOSED HOOD - STREET SIDE VIEW
TETHER TETHER
SCREW SCREW
SCREWS SCREWS
FIGURE 2 FIGURE 2
HOOD ASSEMBLY HOOD ASSEMBLY
DRAWING NO. A68128 REV A (FRONT)
American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH
TM
CONSULT LOCAL CODE AUTHORITY
CAUTION
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
CUPOLA CAP CUPOLA CAP
CUPOLA BASE CUPOLA BASE
CLOSURE CLOSURE
SCREW SCREW
BOSS (2) BOSS (2)
SCREW NOT SCREW NOT
SHOWN SHOWN
LOWER HOUSING LOWER HOUSING
MIN POLE OD 2.375" MIN POLE OD 2.375"
MAX POLE OD 3" MAX POLE OD 3"
HOOD HOOD
REFLECTOR REFLECTOR
PLATE PLATE
©2011 ACUITY LIGHTING GROUP, INC.
WARNING
!
WARNING
!
CAUTION
!
1. TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS. TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.) STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
2. UNSCREW THE TWO 2. UNSCREW THE TWO CAPTIVE
KNOW T THE SCREWS ARE COMPLETELY DISENGAGED FROM KNOW HE SCREWS ARE COMPLETELY DISENGAGED FROM
THE HOOD THE HOOD WHEN WHEN THE SCREWS CAN MOVE FREELY UP AND
DOWN. DOWN.
3. OPEN THE HOOD. 3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE- 4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
TIGHTEN TIGHTEN THE TWO CA THE TWO CAPTIVE CLOSURE SCREWS.
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
SIMPLY PULL BOTH TRIGGERS SIMULTANEOUSLY WITH YOU SIMPLY PULL BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
INDEX FINGER WHILE PUSHING UP ON THE HOOD WITH YOUR INDEX FINGER WHILE
THUMBS. CLOSE THE UNIT BY THUMBS. CLOSE THE UNIT BY CLOSING THE HOOD AND PRESSING
DOWN UNTIL THE TRIGGER LATCHES ENGAGE. DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
PLATE REMOVAL & INSTALLATION: PLATE REMOVAL & INSTALLATION:
1. OPEN THE UNIT. (SEE "OPENING AND CLOSING THE UNIT" 1. OPEN THE UNIT. (SEE "OPENING AND CLOSING THE UNIT"
ABOVE.) ABOVE.)
2. UNSCREW THE TWO SCREWS ATTACHING THE REFLECTOR 2. UNSCREW THE TWO SCREWS ATTACHING THE REFLECTOR
PLATE ASSEMBLY TO THE HOOD. (SEE FIGURE 2). PLATE ASSEMBLY TO THE HOOD. (SEE FIGURE 2).
3. HOLD THE REFLECTOR PLATE AND MOVE BACKWARDS. 3. HOLD THE REFLECTOR PLATE AND MOVE BACKWARDS.
UNSCREW THE SCREW ATTACHING THE TETHER. UNSCREW THE SCREW ATTACHING THE TETHER.
4. DISCONNECTING THE WIRING BY USE OF THE QUICK 4. DISCONNECTING THE WIRING BY USE OF THE QUICK
DISCONNECT. DISCONNECT.
5. TO REINSTALL THE REFLECTOR PLATE ASSEMBLY REPEAT THE 5. TO REINSTALL THE REFLECTOR PLATE ASSEMBLY REPEAT THE
STEPS ABOVE IN REVERSE ORDER. STEPS ABOVE IN REVERSE ORDER.
(UL VERSION) COVER REMOVAL & INSTALLATION: (UL VERSION) COVER REMOVAL & INSTALLATION:
1. UNSCREW 2 SCREWS ATTACHING THE BASE COVER TO THE 1. UNSCREW 2 SCREWS ATTACHING THE BASE COVER TO THE
UNIT. UNIT.
2. LIFT THE BASE COVER FREE. 2. LIFT THE BASE COVER FREE.
3. TO REINSTAL THE BASE COVER, REPEAT THE STEPS ABOVE IN 3. TO REINSTAL THE BASE COVER, REPEAT THE STEPS ABOVE IN
REVERSE ORDER. REVERSE ORDER.
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF
THE REFLECTOR PLATE ASSEMBLY OR UL COVER. THE REFLECTOR PLATE ASSEMBLY OR UL COVER.
OPENING & CLOSING THE UNIT: OPENING & CLOSING THE UNIT:
CAPTIVE CLOSURE SCREWS. YOU WILL CLOSURE SCREWS. YOU WILL
THE SCREWS CAN MOVE FREELY UP AND
TIVE CLOSURE SCREWS.
PUSHING UP ON THE HOOD WITH YOUR
CLOSING THE HOOD AND PRESSING
PART NUMBER 057-71-68128