Best WPB9 Manual
  1. Manuals
  2. Brands
  3. Best Manuals
  4. Ventilation Hood
  5. WPB9
  6. Manual

Best WPB9 Manual

Hide thumbs Also See for WPB9:
Table of Contents

Advertisement

Quick Links

Download this manual
In USA - BEST Hartford, Wisconsin
In CANADA - BEST Drummondville, QC, Canada
REGISTER YOUR PRODUCT ONLINE AT : www.BestRangeHoods.com/register
For additional Information visit www.BestRangeHoods.com
Model WPB9
ENGLISH........................................3
FRANÇAIS...................................18
ESPAÑOL.....................................35

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WPB9 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Best WPB9

Summary of Contents for Best WPB9

  • Page 1 Model WPB9 ENGLISH........3 FRANÇAIS........18 ESPAÑOL........35 In USA - BEST Hartford, Wisconsin In CANADA - BEST Drummondville, QC, Canada REGISTER YOUR PRODUCT ONLINE AT : www.BestRangeHoods.com/register For additional Information visit www.BestRangeHoods.com...

  • Page 3: Grounding Instructions

    READ AND SAVE THESE INSTRUCTIONS INTENDED FOR DOMESTIC COOKING ONLY WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

  • Page 4: To Reduce The Risk Of Injury To Persons In The Event Of A Range Top Grease Fire, Observe The Following

    The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced. 8. For best capture of cooking impurities, the bottom of the hood should be a minimum of 24" and a maximum of 36" above the cooking surface.

  • Page 5: Cleaning And Maintenance

    CLEANING AND MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. Motor The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the motor with the exact service motor. The impeller should also be replaced.

  • Page 6: Operation

    OPERATION Controls (Fig.1) FIG. 1 Button A = turns the lights on/low/high/off. Button B = Activates/Deactivates the delay-off feature. Press once (when blower is on) to activate the delay-off feature. The selected speed level that is displayed in display “C” will blink when this feature is activated.

  • Page 7: Prepare The Hood

    PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flues 1 - Parts Bag (080811032) containing: 1 - Duct Collar 6 - Mounting Screws (3,9 x 9,5mm Pan Head) 2 - Mounting Screws (3,9 x 6mm Flat Head) 6 - Mounting Lag Screws (6 x 60mm) 1 - Flue Mounting Bracket Set 1 - Installation Instructions...

  • Page 8: Install The Ductwork

    INSTALL THE DUCTWORK ROOF CAP NOTE: To reduce the risk of fire, use only metal ductwork. 8” ROUND DUCT 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently.

  • Page 9: Install The Hood

    Minimum hood distance above cook top must not be less than 24”. A maximum of 36” above cook top is highly recommended for best capture of cooking impurities. Distances over 36” are at the installer and the users discretion; and if ceiling height and flue lenght permit.
  • Page 10 MOUNTING LAG SCREWS (6x60mm) WALL FRAMING MOUNTING LAG SCREWS (6x60mm) FIG. 7 FIG. 8 - 10 -...
  • Page 11 MOUNT THE DUCT COLLAR MOUNTING SCREWS 3.9x9.5mm Fix the duct collar to blower discharge with 2 screws (3.9x9.5mm), the screws are located in the Hardware Package (Fig. 9). FIG. 9 WIRING Note: This range hood must be properly grounded. The unit should be installed by a WIRING BOX qualified electrician in accordance with all COVER...

  • Page 12: Install Flue Mounting Bracket

    INSTALL FLUE MOUNTING MOUNTING LAG SCREWS (6x60mm) BRACKET 1. Carefully center the mounting bracket directly over the range hood location. 2. Secure the bracket to the wall using (2) 6 x 60mm mounting lag screws (Fig.11). Make sure the bracket is pushed into the corner, tight against the wall if necessary, and centered over the hood.

  • Page 13: Install Filters

    INSTALL FILTERS NOTE: Prior to use, remove protective film from the filter frame. 1. To remove the GREASE filter, (Fig.15) push the filter towards the front so that it clears the filter channel, then pull down on the handle to disengage the filter from the hood. Tilt the filter downward and remove.

  • Page 14: Calibration Process

    CALIBRATE IQ BLOWER SYSTEM INTERNAL BLOWER DUCTED UNITS ONLY After the hood is installed and wired, engage the calibration process (our Guaranteed Performance System Technology to ensure full-rated airflow is being delivered). Prior to calibration, ensure that all filters, light bulbs and duct system are installed. CALIBRATION PROCESS Hold the calibration button for 3 seconds;...

  • Page 15: Warranty

    ONE YEAR LIMITED WARRANTY FOR BEST PRODUCTS Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

  • Page 16: Service Parts

    SERVICE PARTS MODEL WPB9 KEY NO. PART NO. DESCRIPTION B08087951 Grease Filters B02300804 Heat Sentry B06102611 Wires Assembly B03292499 Runner Wires BE3350233 Wiring Box BE3334252 Wiring Box Cover BE3353371 Flue mounting Bracket B03292290 Wire Clamp B03295035 Fuse Box B03292596 Fairlead...
  • Page 17 - 17 -...

Table of Contents