Additional model. Contact the Alto-Shaam Tech Team Service manuals are available from the Alto-Shaam Department if you have any questions concerning Tech Team Service Department.
SAFETY PROCEDURES AND PRECAUTIONS Knowledge of proper procedures is essential to the 1. This appliance is intended to cook, hold safe operation of electrically and/or gas energized or process foods for the purpose of human equipment. In accordance with generally accepted consumption.
S I T E I N S T A L L A T I O N ELEctricaL The Alto-Shaam Cold Well must be installed in a location ® that will permit it to function for its intended purpose and to...
4. The air cooled self contained units require a sufficient amount of cool clean air. The mechanical housing (except on 100-CW appliances) can be rotated so that the condenser intake air can be in direct line with the cabinet fresh air opening.
I N S T A L L A T I O N D I M E N S I O N S 10 0-C W 18-1/2" (470mm) 2-1/2" (64mm) OPTIONS AND ACCESSORIES 12" (305mm) Half Size / Third-Size Divider Bars 1014395 25-1/8"...
Page 8
I N S T A L L A T I O N D I M E N S I O N S 30 0-C W 44-1/4" (1124mm) 2-1/2" (64mm) 44-1/4" (1124mm) 42-1/4" (1072mm) 25-1/8" (638mm) 40 0-C W 57-1/4" (1453mm) 2-1/2"...
Page 9
I N S T A L L A T I O N D I M E N S I O N S 50 0-C W 70-1/8" (1781mm) 2-1/2" (64mm) 70-1/8" (1781mm) 68-1/16" (1729mm) 25-1/8" (638mm) 60 0-C W 83" (2108mm) 2-1/2"...
CO UNT E R T OP OP E NI NG AI R L O UV ER OPE NI NG 21" H x 16" W 16-7/8" L x 25-1/2" W 100-CW ONE PAN (533mm x 406mm) (429mm x 648mm) 21" H x 16" W 29-7/8"...
Air intake Retractable vent housing must be extended out to engage louver panel then locked down M O DEL 27" 1-1/2" – 7-1/2" 18-1/2" 16-7/8" 25-1/2" 100-CW ONE PAN (686mm) (429mm) (648mm) (38mm – 191mm) (470mm) 27" 1-1/2" – 7-1/2" 31-7/16"...
I N S T A L L A T I O N PL A CEMENT DET AI LS Illustration 1 Side of unit bolt pattern Rear of unit bolt pattern Illustration 2 Wing Nuts To roTaTe compressor (illustration 1), loosen 4 mounting bolts on the top of the compressor cage 1 and 1/2 turns.
I N S T A L L A T I O N C H E C K L I S T P RI OR T O S T A R T - UP Locate nameplate and record the serial number. It will be necessary when ordering replacement parts or requesting warranty service.
1. DO NOT ADD WATER TO COLD WELL NOTE: If your cold pan temperature remains too warm and your temperature control is at the Alto-Shaam cold wells do not require the addition maximum setting, please contact your service of water. Adding water is not recommended technician.
C L E A N I N G A N D P R E V E N T A T I V E M A I N T E N A N C E PROTECTING STAINLESS STEEL SURFACES CLEANING AGENTS It is important to guard against corrosion Use non-abrasive cleaning products designed for in the care of stainless steel...
C A R E A N D C L E A N I N G D A N G E R The cleanliness and appearance of this appliance will contribute considerably AT NO TIME SHOULD THE INTERIOR OR EXTERIOR BE STEAM CLEANED, to operating efficiency and HOSED DOWN, OR FLOODED WITH savory, appetizing food.
S A N I T A T I O N Food fl avor and aroma are usually so closely related The most accurate method of measuring safe temperatures that it is diffi cult, if not impossible, to separate them. of both hot and cold foods is by internal product There is also an important, inseparable relationship temperature.
P R E V E N T A T I V E M A I N T E N A N C E ALTO-SHAAM STRONGLY SUGGESTS A PREVENTATIVE MAINTENANCE PROGRAM which would include the following monthly procedures: T AS K...
T R O U B L E S H O O T I N G PRO BLE M P O SSIB LE CA U SE RE M E DY UNIT WILL NOT COOL Thermostat off Turn thermostat on Unit unplugged Plug in appliance Circuit breaker tripped Replace breaker...
S E R V I C E EXTERIOR SERVICE VIEW (400-CW SHOWN P ar t n um b er s an d d r awi ngs ar e s ub j ec t t o ch ang e wi t ho ut n ot i c e . ITE M D E S CR I P TI O N P A R T NO .
LIMITED WARRANTY Alto-Shaam, Inc. warrants to the original purchaser only that any original part that is found to be defective in material or workmanship will, at Alto-Shaam's option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.