Your problem will likely be resolved in the dealership using the dealer’s facilities, equipment, and personnel. Therefore, it is important that your initial contact be with the dealer. 2. If you did not purchase your equipment from an authorized dealer, call Glenmac, Inc. (see B above); there may Power Box Rake ®...
GENERAL INFORMATION The purpose of this manual is to assist you in operating The illustrations and data used in this manual were and maintaining your Power Box Rake . Read it current at the time of printing, but due to possible ®...
BOLT TORQUE CHART After every ten (10) hours of operation, check all hardware and tighten where required. SAE Series Torque Chart DO NOT use these values if a different torque value or tightening procedure is listed for a specific application. Torque values listed are for general use only.
BOLT TORQUE CHART Metric Series Torque Chart Use only metric tools on metric hardware. Other tools may not fit properly. They may slip and cause injury. DO NOT use these values if a different torque value or tightening procedure is listed for a specific application. Torque values listed are for general use only.
Page 9
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! • Manual. Do not operate until control lever and Keep hands and body away from pressurized lines. equipment movements are correct. Use paper or cardboard, not body parts to check for leaks. Wear safety goggles. Hydraulic fluid •...
Page 10
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! OPERATIONAL SAFETY • No riders are allowed on equipment. • Consult local utilities before digging. Know location • Always sit in tractor seat when operating controls and depth of, and avoid contacting, all underground or starting engine.
Page 11
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! MAINTENANCE SAFETY • Keep all persons away from operator control area while performing adjustments, service, or • Your dealer can supply original equipment, maintenance. hydraulic accessories and repair parts. Substitute parts may not meet original equipment •...
OPERATION Safety is a primary concern in the design and body underneath equipment or between manufacture of our products. Unfortunately, our efforts moveable parts even when the engine has been to provide safe equipment can be wiped out by a single turned off.
OPERATION IMPORTANT PRE-OPERATION CHECK LIST • ___ Review and follow all safety rules and safety If the PTO is too long, severe PTO and gearbox decal instructions on pages 6 through 11. damage is possible when hooking up the PTO from the power rake to the tractor.
OPERATION OPERATING INSTRUCTIONS Power Rake Angle Adjustment Read and understand the power rake and tractor The power rake may be angled up to 15 degrees left or Operator’s Manuals before operating the power rake. right for placing material in a windrow. Failure to do so may result in death, serious personal With the power rake angle cylinder connected to a injury, or property damage.
Page 17
OPERATION Soil can be removed from the windrow of rocks by the tooth roller. The top link is shortened to take the moving it back and forth a few times onto the clean guide wheels off the ground so only the toothed roller area.
OPERATION Shutting Down Lower jackstand to “storage” position. Stop equipment. On a hard level surface, lower attachment to the ground. Lower the lift arms and power rake to the ground. Shut off engine, set brake, remove key, and remove seat belt before leaving the tractor operator’s seat.
MAINTENANCE • The information in this section is written for operators Keep hands and body away from pressurized who possess basic mechanical skills. Should you need lines. Use paper or cardboard, not body parts help, your dealer has trained service technicians to check for leaks.
MAINTENANCE DAILY MAINTENANCE Chain tension is preset with the extension spring. If the chain becomes excessively loose, it may be When operating the power rake, check the tractor necessary to remove one link (two pitches). If unable hydraulic system to be sure the level of hydraulic oil to reassemble, add an offset link to lengthen the chain.
TROUBLE SHOOTING Problem Possible Cause Roller will not turn. Tractor PTO not engaged. Clutch friction discs worn. Obstruction between roller and barrier. Chain broken. Gearbox damaged. Broken drive shaft between clutch and chain drive. Hydraulic cylinder inoperative. Hose ends not completely engaged. Tractor hydraulic shut-off in the “closed”...
MAINTENANCE The information in this section is written for dealer CLUTCH service personnel. The repair described herein requires Run-In special skills and tools. If your shop is not properly If the rake has not been used or has not been operated equipped or your mechanics are not properly trained in for one year, the following run-in procedure is this type of repair, you may be time and money ahead...
MAINTENANCE FRICTION DISC REPLACEMENT the holder. Be careful to press on both the outer and inner bearing races until the inner race rests on the sleeve. See Figure 4. 1. Make sure tractor is off and the PTO is disengaged. 2.
MAINTENANCE Protective Collars Roller Replacement The special protective collars protect bearings from vine It will be necessary to have a lifting device or additional and wire wrap and dirt buildup next to the bearing seal. help while removing and replacing the roller. The roller The bearing protector is sandwiched onto the shaft, weighs approximately 150 lbs.
ASSEMBLY Tools Required CAUTION 3/4", 1-1/8", 1-7/16", and 1-1/2" Wrench • Always wear relatively tight and belted Jackstands clothing to avoid entanglement in moving It is advisable to have a mechanical lifting device to parts. Wear sturdy, rough-soled work shoes facilitate uncrating.
Page 28
ASSEMBLY --IMPORTANT NOTICE-- This should complete the assembly of your new Power Box Rake ® . Make sure that all guards/shields are in ® Do NOT add front PTO half to Power Box Rake place and are not removed during use. yet.
Page 31
GENERAL ASSEMBLY & FRAME ASSEMBLY PARTS LIST ITEM QTY PART NO DESCRIPTION ITEM QTY PART NO DESCRIPTION M6546 BARRIER MOUNT P158005 1/2" NYLOCK NUT M6427 BARRIER P155850 1/2" TOP LOCK NUT M6428 BARRIER STRAP P157200 1/2" 13 HEX JAM NUT M6551 BARRIER PIVOT GUIDE P157500...
Page 37
CLUTCH & PTO DRIVE LINES PARTS LIST ITEM QTY PART NO. DESCRIPTION P400850-1 SIDE PTO CLUTCH HALF P400850-2 SIDE PTO GEAR BOX HALF P400001 CROSS 35R REPAIR KIT P400851 YOKE AND SHAFT SIDE PTO P400853 SHIELD OUTER SIDE PTO P400854 SHIELD INNER SIDE PTO P400852 YOKE AND TUBE SIDE PTO...
This warranty is limited exclusively to equipment manufactured by Glenmac Inc and is subject to inspection by Glenmac Inc to identify the nature and cause of failure. This company in no way warrants belts, bearings, hydrau- lics, chains, sprockets, tires or any other trade accessory not manufactured by Glenmac Inc since these items are warranted separately by their respective manufactures.
Need help?
Do you have a question about the Harley T6 and is the answer not in the manual?
Questions and answers
How do you check the chain oil level in the T6?