Advertisement
1.
2.
3.
4.
1. Input 1 level adjustment
2. Input 1 VU meter
3. Input 2 level adjustment
4. Input 2 VU meter
5. Output 1 level adjustment
Mic
Line
1.
2.
3.
1. 240V AC input
2. 24V DC input
3. Output 6 RCA line level
4. Output 5 RCA line level
5. Output 6 XLR 3 pin mic level
6. Output 5 & 6 DIP switches
7. Output 5 XLR 3 pin mic level
8. Output 4 RCA line level
Figure 1: Front panel DIP switches relating to outputs 1 and 2.
Figure 2: Rear panel DIP switches relating to outputs 1 and 2.
Mic
Line
Figure 3: Rear panel DIP switch configuration. This is also printed on the rear of the unit
for handy reference.
5.
6.
7.
6. Output 1 & 2 DIP switches
7. Output 2 level adjustment
8. Output 3 level adjustment
9. Output 3 & 4 DIP switches
10. Output 4 level adjustment
4.
5.
6.
7.
8.
9. Output 3 RCA line level
10. Output 4 XLR 3 pin mic level
11. Output 3 & 4 DIP switches
12. Output 3 XLR 3 pin mic level
13. Output 2 RCA line level
14. Output 1 RCA line level
15. Output 2 XLR 3 pin mic level
16. Output 1 & 2 DIP switches
No Connection
ON
1 2 3 4
A 4415 2 Input / 6 Output Audio Splitter
8.
9.
10.
FRONT PANEL
9.
10. 11. 12.
13. 14.
REAR PANEL
Mic
Line
11.
12.
13.
11. Output 5 level adjustment
12. Output 5 & 6 DIP switches
13. Output 6 level adjustment
14. Power LED
15. Power switch
15. 16. 17.
18. 19.
17. Output 1 XLR 3 pin mic level
18. Input 2 RCA line level
19. Input 1 RCA line level
20. Input 2 XLR 3 pin mic level
21. Input 1 & 2 DIP switches
22. Input 1 XLR 3 pin mic level
DIP Switch Setup
The DIP switches on the front panel are used to
route inputs 1 and 2 to all 6 outputs.
Figure 1 shows the DIP switches related to outputs
1 and 2.
In this example:
Switch 1 will route input 1 to output 1
Switch 2 will route input 2 to output 1
Switch 3 will route input 1 to output 2
Switch 4 will route input 2 to output 2
Any configuration can be used. ie inputs 1 and 2
can be routed to outputs 1 and 2 simultaneously.
Figure 2 shows the configuration for outputs 1 and
2 plus the DIP switch associated with these out-
puts.
This DIP switch allows each of the 6 outputs to be
configured as either balanced microphone or bal-
anced line level signal.
In this example DIP switch 1 will set output 2 to
either XLR balanced or RCA balanced line level.
DIP switch 4 will set output 2 to either XLR bal-
anced or RCA balanced line level.
Figure 3 shows the configuration for all the DIP
switches on the rear of the unit. Switches 2 and 3
have no connection.
Power
The unit can be powered from a 24V DC source for
use in battery backup installations. Connection is
via 2.1mm DC socket..
14.
15.
20. 21. 22.
Page 2
Advertisement
