Vetek VB2-10K Manual

Manual force meter weighingblock

Advertisement

Manual Force Meter Weighingblock VB2-10K
Note:
- At last page in this manual you will find a short form instruction. Normally the only
instruction shipped together with the Force Meter.
Hantverksvägen 15, 76493 Väddö Sweden
Tel +46 176 208 920
info@vetek.com
Calibration switch
ON
PRINT
O
NET
GROSS
OFF
ZERO
TARE
The Weighingblock is a robust Force Meter. It is
designed for portable use. When transported by car
between different working places we recommend
using of a protected space or a case. This will extend
the interval for service.
com
www.vetek.
Alkaline battery 9 V
9VDC jack
(2,1mm center
minus)
page 1
Manual_VB2-10K_V1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VB2-10K and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vetek VB2-10K

  • Page 1 Manual Force Meter Weighingblock VB2-10K Note: - At last page in this manual you will find a short form instruction. Normally the only instruction shipped together with the Force Meter. 9VDC jack (2,1mm center Calibration switch Alkaline battery 9 V...
  • Page 2: Table Of Contents

    Used to establish a Tare (zero the Force Meter) while in either Gross mode or Net mode. This operation cannot be performed at or below Gross zero. page 2 Hantverksvägen 15, 76493 Väddö Sweden Tel +46 176 208 920 info@vetek.com www.vetek.
  • Page 3 Indicates that a tare weight/force has been established in the system. lb, kg Indicates the unit of the displayed weight/force (normally disabled). bAtt Indicates a low battery condition. Indicates stable measuring. VB2 Enunciator Definitions page 3 Hantverksvägen 15, 76493 Väddö Sweden Tel +46 176 208 920 info@vetek.com www.vetek.
  • Page 4: Parameters

    "1" = Enable the lb/kg key Selects the auto off time period in minutes: 1, 2, 4, 10, 20, 60, off Auto Power Off “Off” = Disabled (Always ON) Period page 4 Hantverksvägen 15, 76493 Väddö Sweden Tel +46 176 208 920 info@vetek.com www.vetek.
  • Page 5: Calibration

    "Err2" – The internal resolution of the Force Meter is not high enough to accept the calibration value. Select a larger parameter for the Span Gain (F2). Press Calibration Switch one time for normal mode. page 5 Hantverksvägen 15, 76493 Väddö Sweden Tel +46 176 208 920 info@vetek.com www.vetek.
  • Page 6: Specifications And Displayed Error Codes

    No reading from the ADC. Make sure there is a load cell(s) connected to the indicator at start-up. Err 9 Normal Operating Span calibration value has been lost. Re-calibrate the Force Meter. Mode page 6 Hantverksvägen 15, 76493 Väddö Sweden Tel +46 176 208 920 info@vetek.com www.vetek.
  • Page 7: Fault Localization And Repair

    1. If only the first,F1, has been changed. Set back to right value in accordance to the table. 2. If many parameters has been changed. Check all parameter values. Probably it is necessary to calibrate the Weighingblock. page 7 Hantverksvägen 15, 76493 Väddö Sweden Tel +46 176 208 920 info@vetek.com www.vetek.
  • Page 8: Instruction For Handling

    This instruction is for the user of the Force Meter. It is the last site in the complete manual. Hopefully is this the only needed information. For complete information, contact you wholesaler, Vetek AB or download it from our web site http://www.vetek.net...

Table of Contents