Table of Contents
Advertisement
Quick Links
QMS2400TECH
Technical Instructions
CORPORATE
LOS ANGELES, USA
US 1 800 394.9900
Int'l +1 818 837.8100
FAX 1 800 394.9910
Int'l +1 818 838.7047
ATLANTA, USA
US 1 877 676.4223
Int'l +1 770 516.9488
FAX 1 877 337.7976
Int'l +1 770 516.7794
DALLAS, USA
US 1 877 499.4989
Int'l +1 972 840.4989
FAX 1 877 774.1750
Int'l +1 972 840.1750
MIAMI, USA
US 1 800 595.429
Int'l +1 305 594.3396
FAX 1 800 522.8640
Int'l +1 305 594.3309
NEW YORK, USA
US 1 800 431.7884
Int'l +1 631 345.0121
FAX 1 800 431.8812
Int'l +1 631345.0690
SANFORD,USA
US 1 800 786.9049
Int'l +1 919 775.4584
FAX 1 800 786.9049
Int'l +1 919 775.4584
TORONTO, CAN
CAN 1 877 848.0818
Int'l +1 905 712.9501
FAX 1 877 772.6773
Int'l +1 905 712.9502
BUENOS AIRES, ARG
ARG 0810 444.2656
Int'l +011 4583.5900
FAX +011 4584.3100
MELBOURNE, AUS
AUS 1 800 003. 100
Int'l +62 03 9561.8102
FAX 1 800 004.302
Int'l +62 03 9561-7751
SYDNEY, AUS
AUS 1 800 003.100
Int'l +62 02 9648.2630
FAX 1800 004.302
Int'l +62 02 9548.2635
MONTEVIDEO,URY
URY 02 902.7206
Int'l +5982 900.8358
FAX +5982 908.3816
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
E-mail: info@futuregraphicsllc.com
REV. 9/19/05
Cartridge Information
See Last Page.
Photo 1
Photo 2
Photo 3
Photo 4
See Last Page.
Step 1
Position the cartridge with the developer
roller drive gear end cap facing you.
Remove three silver colored Phillips
screws from the end cap. Remove the end
cap. (Photo 1)
Step 2
Place the cartridge with the developer
roller facing you. Rotate the cartridge so
that the developer roller is facing down-
ward. Using a small flat blade screwdriv-
er release the two latches that hold the
doctor blade cover in place, remove and
set aside. (Photo 2)
Step 3
Turn the cartridge so that the developer
roller drive gear end is facing away from
you and remove the capped white center
bearing by gently lifting the center tab and
rotating the cap counter clockwise until it
stops. You can now pry the capped white
center bearing off. (Photo 3)
Step 4
Place the cartridge with the developer
roller facing you. Rotate the cartridge so
that the developer roller is facing upward.
Remove the silver shoulder screw located
on the Recovery / Toner Hopper Seal
Plate with gasket assembly.
remove the center bearing with ground
plate by lifting the ground plate up and
pulling the center bearing plate out. Be
very careful not to damage this assembly
during removal, cleaning and reinstalla-
tion. (Photo 4)
Website:
www.futuregraphicsllc.com
Tools & Supplies
1
Carefully
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Minolta QMS Magicolor 2400 DL
Summary of Contents for Minolta QMS Magicolor 2400 DL
- Page 1 QMS2400TECH Technical Instructions Cartridge Information Tools & Supplies See Last Page. See Last Page. CORPORATE LOS ANGELES, USA US 1 800 394.9900 Photo 1 Int’l +1 818 837.8100 Step 1 FAX 1 800 394.9910 Int’l +1 818 838.7047 Position the cartridge with the developer ATLANTA, USA roller drive gear end cap facing you.
- Page 2 Minolta/QMS Magicolor 2400 DL Technical Instructions Photo 5 Step 5 Using your fingers grasp the ends of the developer roller shaft and remove with Notes both developer bearings and developer roller driver gear still installed. Remove the bearings and drive gear for further clean- ing.
- Page 3 Minolta/QMS Magicolor 2400 DL Technical Instructions Photo 10 Step 10 With the toner fill hole side of the cartridge facing right and the opening for the devel- Notes oper roller facing you reinstall the Recovery / Toner Hopper Seal Plate with...
- Page 4 Minolta/QMS Magicolor 2400 DL Technical Instructions Photo 16 Step 16 Move the toner hoper so that the gear side Step 15 is facing you. Place the black end cap back Place the cartridge with the into position. Install three silver colored developer roller facing you.
Need help?
Do you have a question about the QMS Magicolor 2400 DL and is the answer not in the manual?
Questions and answers