Product Structural Diagram 1. Control Panel 2. Fork Assembly 3. Fork Handle 4. Grill 5. Bakeware 6. Water tank 7. Handle 8. Door 9. Water tray 10. Body 11. Door switch 12. Glove IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1.
Page 4
9. Do not let cord hang over edge of table or counter, or touch hot surfaces. 10. Do not place on or near a hot gas or electric burner, or in a heated oven. 11. Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
5. Do not use this product if the plug, power cord or the product is damaged; 6. If the power cord is damaged, it must be replaced by the manufacturer or its professional service technicians in order to avoid the danger; 7.
Page 6
7. Please clean the door glass of the oven with a soft and wet cloth rather than any sharp cleaning tools to prevent the damage to the door glass; 8. The appliance cannot be operated under the circumstances that it connects the external timer or the independent remote control system;...
Control Panel D IY ① ② ③ ④ ⑤ Icon Function Description Oven lamp/child lock key: 1. Touch it once, oven lamp is ON; touch it again, oven lamp goes out; 2. Oven lamp will be ON for three minutes after the work is over; 3.
Page 8
Description Function The first two LEDs are hours (0-24)and the Time second two LEDs are minutes (0-59) °F - °F Temperature Adjustable range: 85 Preset function prompt Working time -delay prompt Icon is always ON for water; a flashing light Water level icon means a lack of water.
Operating Instructions 1. First Energization The machine enters the full-screen standby interface after a “beep” sound when it is energized rstly by touching power ON . During the setting process, if there is no operation for continuous in three minutes all current settings will be cancelled and the machine will return to the standby interface for a standby status.
Page 10
7. When the menu “Roast” is selected, icon is ON. The temperature display column will show “F-1”, and meanwhile, the time display column will show the required working time. Press the selection key “ ”, the temperature display column will show “F-1”, “F-2”, “F-3” … “F-9”.. “F-1”, and repeat this circle, and the corresponding time column will show the required time.
Page 11
2. Setting of working hours °F °F 3. Setting of working hours and temperature, top heater pipe icon “ ” will ash. °F 4. Start work °F Attention: All functions shall be adjusted according to this adjustmen order except for the xed time and temperature. Note: Water tank icon will be displayed when a steam-related function is selected (such as, steam, high-temperature steam, ferment, unfreeze etc.), for example: °F...
Page 12
After the temperature is adjusted, press the ENTER key to start the work; The time-delay “ ” function is not available for the descaling program. After it is completed, the system directly enters the END interface. 6. End of Work After the program process is ended, “END”...
Page 13
1. DIY Steam Adjustable temperature range: 120-230°F, with each adjusting scale of 40°F. In the standby status, open the oven door, take out the water tank to ll the water to its maximum scale; put in the water tank and food and then close the oven door.
minute selection mode and then, the minute icon will ash. Press the SELECTION key to select the required time (default value is 30, ranging from 0-59). After it is selected, press the ENTER key to enter the temperature selection mode and then, the temperature icon will ash.
3. “Bake” menu Code H -1 H -3 Baguette Yogurt Food Wheat Chocolate Chiffon Cookies Pizza Puff Egg tart Style bread cheese cake cake bread cake Heating time minute Heating temperature °F 4 “Air Fryer” menu Code P -1 Food Pork Onion Chicken...
Page 16
2. The descaling mixture (water and clearing media) is prepared according to the mixing ratio of 1:8 and then put into the water tank after an even mixing. The dosage of descaling mixture in the water tank may not be lower than the descaling scale of water tank.
• Water level detection protection When the working state of steam mode is started, if water shortage is detected, the machine will stop the work and the buzzer will give an alarm, and then all keys or buttons are invalid. The machine resumes the work after the water is added. •...
Guideline for Troubleshooting Abnormal Possible causes Solution conditions Stop the work, open the oven door and allow the cavity to cool down for 10 Open circuit for top sensor minutes, and then restart it or contact the after-sales service. Stop the work, open the oven door and allow the cavity to cool down for 10 Short circuit for top sensor minutes, and then restart it or contact...
Need help?
Do you have a question about the PKSTMOVN72 and is the answer not in the manual?
Questions and answers