Table of Contents
Advertisement
INTERFACE TELEFÓNICO
INTERFACE TELEFÓNICO
« TELEPHONE INTERFACE MANUAL »
Ref.1088 - Telephone Interface for ADS systems.
Ref. 4300 - Telephone Interface for 4+N systems.
Technical publication of informative nature edited by FERMAX ELECTRONICA S.A.E.
FERMAX ELECTRONICA S.A.E., in a policy of ongoing enhancement, reserves the right to modify the
contents of this document as well as the features of the products described herein at any time and without
prior notice. Any modifications will be reflected in subsequent editions of this document.
ENGLISH
16
Advertisement
Table of Contents
Related Manuals for Fermax 1088
Summary of Contents for Fermax 1088
- Page 1 Technical publication of informative nature edited by FERMAX ELECTRONICA S.A.E. FERMAX ELECTRONICA S.A.E., in a policy of ongoing enhancement, reserves the right to modify the contents of this document as well as the features of the products described herein at any time and without prior notice.
-
Page 2: Table Of Contents
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO INDEX INTRODUCTION ............................... 4 CONFIGURATION ............................. 5 TYPICAL SETUP ............................5 MIXED SETUP ............................... 5 SETUP WITH TELEPHONE SWITCHBOARD, CONNECTION IN EXTENSIONS ........6 SETUP WITH TELEPHONE SWITCHBOARD, CONNECTION ON LINE ..........6 INSTALLATION DIAGRAM - CONVENTIONAL SYSTEM (4+n) ..............7 INSTALLATION DIAGRAM - ADS SYSTEM ..................... -
Page 3: Introduction
TheTelephone Interface is supplied in two different versions: - For Conventional 4+N System (Ref.4300) Compatible with all Fermax conventional system amplifiers (both electronic call and buzzer) - For ADS System (Ref.1088) The maximum number of telephones connected to the Telephone Interface to ensure correct operation is 4 (the same as with telephone companies). -
Page 4: Configuration
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO CONFIGURATION The Telephone Interface enables the house telephones to receive and answer calls from the automatic porter and it is also possible to divert them out by means of the telephone line. Here are some examples in block diagram format: TYPICAL SETUP All the telephones also carry out electronic door control functions. -
Page 5: Setup With Telephone Switchboard, Connection In Extensions
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO SETUP WITH TELEPHONE SWITCHBOARD, CONNECTION ON LINE Telephone Interface intercepts the line before it enters the switchboard and so all the extensions depending on the inbound line will receive the calls from the outdoor panel. TELEPHONE LINES EXAMPLE •... -
Page 6: Installation Diagram - Conventional System (4+N)
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO INSTALLATION DIAGRAMS - CONVENTIONAL SYSTEM (4+n) -
Page 7: Installation Diagram - Ads System
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO INSTALLATION DIAGRAM - ADS System... -
Page 8: Programming Installation Parameters
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO PROGRAMMING INSTALLATION PARAMETERS Installation Parameters are configured when the Interface is installed and are not usually modified afterwards. The following table shows some of these parameters. Digit Parameter Value System House number (ADS Number) 1-199 Number the panel identifies Interface with. Open door timing 1-200 Time door release mechanism is activated. -
Page 9: Programming Example 1
Let’s see how to program the ADS number: This only needs to be done if you have Telephone Interface Ref. 1088. - Proceed with the first 2 steps as in the example above. In step 3, key in 0, (digit corresponding to the ADS Number parameter as appears in the table on the previous page). -
Page 10: Programming User Parameters
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO PROGRAMMING USER PARAMETERS The User Parameters are those that may be modified most often in line with the user’s needs. The following table shows what these are: Digit Parameter Value System Divert Telephone. TELEPHONE BOTH NUMBER Telephone number calls will be diverted to. -
Page 11: Operation
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO OPERATION • If the telephone is not in use, a characteristic ring is generated until answered or 30 seconds have elapsed. When you answer you have 90 seconds to communicate with the door intercom. Once communication is established, you can carry out a series of operations, such as: - Open the door by pressing ‘5’... -
Page 12: Additional Operations With Outdoor Panel
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO ADDITIONAL OPERATIONS WITH OUTDOOR PANEL If communication with the outdoor panel has not been established, you can take the following steps: - Call the guard unit (if there is one) by pressing ‘*’ and ‘4’ consecutively. - In ADS systems you can activate panel 1 by pressing ‘*’... -
Page 13: Troubleshooting
INTERFACE TELEFÓNICO INTERFACE TELEFÓNICO TROUBLESHOOTING INTERFACE DOES NOT WORK • IS THE RED INTERFACE LED LIT ? - No: Make sure the equipment is receiving power and that the source is connected. - Yes: Check the door control connections and that the telephone has tone dialling. •... -
Page 14: Technical Features
700 mA in communication Operating Temperature 0 - 60 ºC Hr 90 % Connectors: Ref. 1088 / ADS System +, - : 18 Vdc supply L: ADS system line L Ref. 4300 / 4+N System 1: door release 2: audio from 4+N system...