VDC Display Systems MARQUEE 8521 Ultra Green User Manual page 24

To prepare setup memories for the above system, follow these steps:
Step 1. Select the input using the Source command. Press [SOURCE] [ 0 ] [ 1 ] to select projector slot
1.
Step 2. Press [ ] twice to display the Current Input Parameters status page. Check to see if ASR is
off for the current input. If it is on, press [UTIL] [ 1 ] [ 4 ] to turn ASR off for the input. (It is
usually easier to prepare setup memories when ASR is turned off.)
Step 3. At the computer, switch to an application which uses one of the graphics adapter operating
modes. Select an unused Recall memory as the current setup memory. For example, to make
Recall memory 01 the current setup memory, press [RECALL] [ 0 ] [ 1 ]. Make display
adjustments as required. The display settings for the current graphics mode will be stored in
the Recall memory. Repeat this step for the remaining graphics adapter operating modes,
storing adjustments for them in Recall memories 02, 03 and 04. It is recommended that the
two extreme frequencies be set up first.
Step 4. Press [SOURCE] [ 0 ] [ 1 ] to make Input memory 01 the current setup memory then press
[UTIL] [ 1 ] [ 5 ] to display the Clear Setup dialog box. Move the cursor to "Do It" then press
[ENTER] to clear the display and frequency settings of the input. Now Input memory 01 will not
be used during an ASR search.
Step 5. Press [UTIL] [ 1 ] [ 3 ] to lock Input memory 01 to prevent display or frequency changes to the
Input memory.
Step 6. Press [UTIL] [ 1 ] [ 4 ] to turn ASR on for the input. Now, each time the computer's graphics
adapter switches operating modes, the projector will automatically adjust its display settings to
suit the new mode.
2.7.7.3 ASR Example #2
Six different sources are connected to a third party (non-Reseller) signal switcher. Unlike the Marquee signal
switcher, this third party switcher is not controlled by the keypad. Under normal circumstances, the projector is
not aware of source switches made by the switcher. However, if ASR is turned on for the input, and a Recall
memory has been set up for each source device, the projector will detect the external source switch and
automatically select the appropriate Recall memory. Even if Recall memories have not been set up but ASR is
on, ASR will try to adjust the display settings based on the settings of other Input or Recall memories.
To prepare setup memories for this system, follow these steps:
Step 1. Connect the output of the signal switcher to a projector input or a Marquee signal switcher
input. Select the input using the Source command. For this example, press [SOURCE] [ 0 ]
[ 1 ] to select projector slot 1.
Step 2. Press [ ] twice to display the Current Input Parameters status page. Check to see if ASR is
off for the current input. If it is on, press [EXIT] then press [UTIL] [ 1 ] [ 4 ] to turn ASR off for
the input.
Step 3. At the switcher, switch in one of the source devices. Select an unused Recall memory as the
current setup memory. For example, to make Recall memory 01 the current setup memory,
press [RECALL] [ 0 ] [ 1 ]. Make display adjustments as required. The display settings for the
selected device will be stored in the Recall memory. Repeat this step for the remaining
devices.
Step 4. Press [UTIL] [ 1 ] [ 5 ] to display the Clear Setup dialog box. Move the cursor to "Do It" then
press [ENTER] to clear the display settings and frequency settings of the input. By doing this,
Input memory 01 will not be used during an ASR search.
Step 5. Press [UTIL] [ 1 ] [ 3 ] to lock Input memory 01 to prevent display or frequency changes to the
Input memory.
Step 6. Press [UTIL] [ 1 ] [ 4 ] to turn ASR on for the input. The projector's display settings will
automatically adjust to match the source selected by the switcher.
Display Systems
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Section 2
2-13