Download Print this page
Murdock A172-SO Series Installation & Maintenance Instructions Manual

Murdock A172-SO Series Installation & Maintenance Instructions Manual

Barrier free, sensor operated, wall mounted drinking fountain

Advertisement

Quick Links

A172100F-SO
TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:
NOTES TO INSTALLER:
1. Please leave this documentation with the owner of the fixture when finished.
2. Please read this entire booklet before beginning the installation.
3. Check your installation for compliance with plumbing, electrical and other applicable codes.
Murdock warrants that its products are free from defects in material or workmanship under normal use and
service for a period of one year from date of original shipment or for 18 months after the date of shipment from the
factory, whichever comes first. Murdock's liability under this warranty shall be discharged solely by replacement
or repair of defective material, provided Murdock is notified in writing within one year from date of shipment,
F.O.B. Industry, California.
This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges
caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all
other warranties expressed or implied. Product maintenance instructions are issued with each unit and disregard
or non-compliance with these instructions will constitute an abnormal use condition and void the warranty.
Stainless steel must be protected on job site during construction and must be properly maintained after the water
has been introduced into the water cooler or drinking fountain, or Murdock's limited warranty is void.
LIMITED EXPORT WARRANTY - One year on parts only.
Murdock assumes no responsibility for use of void or
suspended data. © Copyright Murdock, City of
Industry, CA Member of Morris Group International.
Please visit www.murdockmfg.com for most
current specifications.
7020-961-001
Date: 12/20/17
CONTEMPORARY WATER COOLERS
DRINKING FOUNTAIN
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
A172-SO Series
Barrier Free, Sensor Operated,
Wall Mounted Drinking Fountain
1.800.591.9360
Technical Assistance Fax: 1.626.855.4894
LIMITED WARRANTY - UNITED STATES & CANADA
Federal
Test rating conditions are
Public Law
111-380
compliant with ARI 1010.
(No Lead)
OR
A174100F-SO
Member of
MURDOCK
15125 Proctor Ave.
City of Industry, CA
91746 U.S.A.
Phone 800-591-9360
626-336-4561
Fax 626-855-4894
www.murdockmfg.com

Advertisement

loading

Summary of Contents for Murdock A172-SO Series

  • Page 1 18 months after the date of shipment from the factory, whichever comes first. Murdock’s liability under this warranty shall be discharged solely by replacement or repair of defective material, provided Murdock is notified in writing within one year from date of shipment, F.O.B. Industry, California.
  • Page 2 30” maximum above finished floor. Provide clear floor space as required. Adjust vertical dimensions as required to comply with federal, state, and local codes. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 •...
  • Page 3: Installation

    Murdock Mfg. 6. Fixture operates within water pressure range of 20 to 105 PSIG (138 to 724 kPa). Murdock Mfg. will not warranty fixtures damaged when connected to supply lines with flow pressure lower than 20 PSIG (138 kPa) or higher than 105 PSIG (724 kPa).
  • Page 4 There is debris or scale in the center or two holes in convolution of the Water Diaphragm. Remove and clean. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com...
  • Page 5 3. Apply stainless steel cleaner/ polish to the synthetic abrasive pads and carefully rub the panel with the grain. 4. DO NOT use harsh chemicals, abrasive or petroleum based cleaners. Use of these will void the Murdock warranty. DO NOT use abrasives on powder coated units.
  • Page 6 #8 ZINC, HEX, SHEET METAL SCREW 0124-010-000 #10 PHILLIPS ROUND HEAD 1895-709-000 ELBOW, PUSH-IN 1/4” O.D. x 1/4” STEM MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-961-001 Revised:...
  • Page 7 REPLACEMENT CARTRIDGE ITEM PART NUMBER DESCRIPTION 7012-313-000 WF1 FILTER REPLACEMENT CARTRIDGE MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-961-001 Revised: 12/20/17 A172-SO Page 7 of 10...
  • Page 8 Push-In Fitting Body and hold. While holding the Collet in, pull on the PE Tubing to remove from the Push-In Fitting. COLLET MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-961-001...
  • Page 9 15" 15" All 1/4" O.D. Plastic tubing 21 must be insulated with 22 foam insulation. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com 7020-961-001...
  • Page 10 7000-059-199 1-1/4" - 18 NORMALLY OPEN VALVE CAP 7000-050-001 VALVE CARTRIDGE ASSEMBLY Repairs must be made with Murdock Mfg. parts only. Please order through your local representative or distributor. The phone number to locate your local representative is 1.800.591.9360. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of Phone 800-453-7465 or 626-333-2543 •...

This manual is also suitable for:

A172100f-soA174100f-so