Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Jupiter Avionics JA34-BT1
Summary of Contents for Jupiter Avionics JA34-BT1
- Page 1 JA34-BT1 Universal Radio Adapter ® With Bluetooth Installation and Operating Manual Rev D Jupiter Avionics Corporation 1959 Kirschner Road Kelowna BC Canada V1Y 4N7 Tel: +1 778 478 2232 Toll-Free: 1 855 478 2232 www.jupiteravionics.com Rev B Page i...
- Page 2 All rights reserved Jupiter Avionics Corporation (JAC) permits a single copy of this manual to be printed or downloaded for the express use of an installing agency. Any such electronic or printed copy of this manual must contain the complete text of this copyright notice.
-
Page 3: Table Of Contents
JA34-BT1 Universal Radio Adapter with Bluetooth ® Installation and Operating Manual Table of Contents SECTION 1 - DESCRIPTION ..............................1 System Overview ..............................1 Features Overview ..............................1 Inputs and Outputs ..............................1 1.3.1 Inputs ................................1 1.3.2 Outputs ................................1 Specifications ................................ -
Page 4: Section 1 - Description
Microphone biasing and artificial sidetone generation are selectable for radios without them. The JA34-BT1 is setup on a per installation basis using a Configuration Cable and downloading the system configuration settings from a PC into non-volatile control devices. -
Page 5: Specifications
JA34-B BT1 Univers sal Radio A Adapter with h Bluetooth ® Installation and Opera ting Manua Specific cations 1.4.1 Electrica l Specificat tions Power Inp Nominal vo oltage 28 Vdc Maximum voltage 30.3 Vdc Minimum v voltage 22.0 Vdc Emergenc y voltage 18.0 Vdc Input curre... -
Page 6: Mechanical Specifications
(2) doit accepter toute interférence, y compris les interférences pouvant entraîner un fonctionnement indésirable de llllll l'appareil. 1.4.7 Co-location with Other Transmitters Ensure all JA34-BT1 units are installed with at least 20 cm between other JA34-BT1 units and antennae from other transmitting equipment. Rev D Page 3... -
Page 7: Section 2 - Installation
Introduction This section contains unpacking and inspection procedures, installation information, and post-installation checks. Continued Airworthiness Maintenance of the JA34-BT1 is on condition only. Scheduled inspection and/or periodic maintenance of this unit is not required. Unpacking and Inspecting Equipment Unpack the equipment carefully. Check for shipping damage and report any problems to the relevant carrier. Confirm that the Authorized Release Certificate or Certificate of Conformance is included. -
Page 8: Mechanical Installation
2.4.3 Mechanical Installation The JA34-BT1 can be mounted in any attitude and location with adequate space and sufficient clearance for the connector and wiring harness. It requires no direct cooling. Ensure all JA34-BT1 units are installed with at least 20 cm between other JA34-BT1 units and antennae from other transmitting equipment. -
Page 9: Receive Operation
All the JA34-BT1 internal adjustments are set from the Product Configuration Software ProCS™. Configuration data is sent to the JA34-BT1 via the front panel connector (♫/io), using the Configuration Cables and a computer running the ProCS™ software. For configuration requirements, see section 2.5.1. -
Page 10: Configurable Settings
Note: To configure the JA34-BT1, power must be applied to the unit. Within ProCS™, the configurable settings are grouped together into the following sections: 2.6.4... -
Page 11: Aircraft Audio Systems List
2.6.5 Aircraft Audio Systems List This is a list of Aircraft Audio Systems, and shows the configuration information that will be added to the JA34-BT1 Settings page. If it is desirable to add other Audio systems, click on the Aircraft Audio Systems List. A new audio system and its parameters can be added by clicking on (the ‘New Aircraft Audio System' button). -
Page 12: Non-Aircraft Radios List
Non-Aircraft Radios List This is a list of Non-Aircraft Radios and the configuration information that will be added to the JA34-BT1 Settings page. The list is similar to the Aircraft Audio Systems list, and new radios can be added in the same way. -
Page 13: Section 3 - Operation
® enabled device such as a cell phone is introduced into the aircraft, it can be paired with the JA34-BT1. The Bluetooth transceiver can be configured at installation or in the field by a dealer or installer, using the Jupiter ®... -
Page 14: Bluetooth Status Indicator
JA34-BT1 Universal Radio Adapter with Bluetooth ® Installation and Operating Manual 3.3.1 iPhone Connectivity Configuration The default setting for Call Audio Routing allows the iPhone to select where to route calls; either to the built-in speaker or a Bluetooth headset. This can cause response delays and possible 'dropped calls'. -
Page 15: Appendix A - Installation Drawings
JA34-BT1 Universal Radio Adapter with Bluetooth ® Installation and Operating Manual Appendix A - Installation Drawings Introduction The drawings necessary for installation and troubleshooting of the JA34-BT1 Universal Radio Adapter with Bluetooth are in this Appendix, as listed below. Installation Drawings DOCUMENT... - Page 16 PREPARED 04-23-14 CHECKED TITLE Universal Radio Adapter With Bluetooth APPROVED 04-23-14 NCAGE CODE PART NO. SHEET L00N3 JA34-BT1 DOC NO. CONFIDENTIAL & PROPRIETARY JA34-BT1 Connector Map Rev A.dwg TO JUPITER AVIONICS CORP. JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
- Page 17 Connection to airframe ground should be made with 20 AWG wire. Length not to exceed 3 FT (0.9 M). Cable shields at the JA34-BT1 connector pins should be terminated to airframe ground using a tag ring P/N: MS27741-3 or equivalent.
- Page 18 OUTPUT GROUND 21 PREPARED 02-13-19 CHECKED TITLE Universal Radio Adapter With Bluetooth 02-13-19 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA34-BT1 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA34-BT1 Interconnect Rev C.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
- Page 19 OUTPUT GROUND 21 PREPARED 02-13-19 CHECKED TITLE Universal Radio Adapter With Bluetooth 02-13-19 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA34-BT1 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA34-BT1 Interconnect Rev C.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
- Page 20 OUTPUT GROUND 21 PREPARED 02-13-19 CHECKED TITLE Universal Radio Adapter With Bluetooth 02-13-19 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA34-BT1 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA34-BT1 Interconnect Rev C.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
- Page 21 TITLE Universal Radio Adapter With Bluetooth J2 and J3 Interconnect 02-13-19 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA34-BT1 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA34-BT1 Interconnect Rev C.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
- Page 22 OPTION: JA34-BT1 Interconnect to a Transceiver and a Mobile Phone with music. JA34-BT1 25 PIN FEMALE DMIN MATING CONNECTOR 22 AWG. +28 VDC POWER +28 VDC POWER SPARE 22 AWG. POWER GROUND 14 POWER GROUND 20 AWG. CHASSIS GROUND 15...
- Page 23 ANGLES: 0.5 DEG SHEET 06-05-15 NCAGE CODE PART NO. APPROVED L00N3 JA34-BT1 CONFIDENTIAL & PROPRIETARY DOC. NO. MATERIAL: TO JUPITER AVIONICS CORP. JA34-BT1 Mechanical Installation Rev C.SLDDRW FINISH: DRAWING NOT TO SCALE JUPITER AVIONICS TEMPLATE SOLIDWORKS PORTRAIT SIZEA REVB .DRWDOT...
-
Page 24: Appendix B - Installation Documents
JA34-BT1 Universal Radio Adapter with Bluetooth ® Installation and Operating Manual Appendix B - Installation Documents Rev D Page B1... -
Page 25: B1 Airworthiness Approval
Removed the existing [model] radio adapter and replaced with a Jupiter Avionics JA34-BT1 Universal Radio Adapter with Bluetooth in [aircraft location]. Installed in accordance with the JA34-BT1 Installation & Operating Manual, Revision [ ], and AC 43.13-2, Chapters 2, and 3. - Page 26 Refer to the JA34-BT1 Maintenance Manual. 7. Removal and Replacement Information Refer to Section 2 of this manual - the JA34-BT1 Installation & Operating Manual. If the unit is removed and reinstalled, a functional check of the equipment should be conducted.