Page 2
SCHNEIDER ELECTRONICS GMBH-GERMANY 1. CAUTION CA UTION: Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UT ION : T O RE DUCE TH E RIS K OF CA U T ION ELECTR ICA L SHOCK, DO NOT RE MOVE COVER (OR BACK).
Page 3
SCHNEIDER ELECTRONICS GMBH-GERMANY IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and Instructions marked on the audio equipment. 1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated. 2.
Page 4
SCHNEIDER ELECTRONICS GMBH-GERMANY PROTECTION AND LOCATION OF YOUR SET Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
Page 5
SCHNEIDER ELECTRONICS GMBH-GERMANY OPERATION OF YOUR SET 18. This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
Page 6
TCL MULTIMEDIA LCD TV SPECIFICATION RELEASE Version: V1.0 Issued Date: 2013.04.10 Model: LED28B2500/MS306D-ISDB-T LA PICTURE Panel Size (inch) 28" Category LCD TV Aspect Ratio 16:9 Color Temperature Medium/Warm/Cool SIGNAL FORMAT CAPABILITY Backlight Adjustable Component Video Format Y,Pb/Cb,Pr/Cr:up to 1080P Scaler Mode...
第 1 页共 11 页 文件编号:CRT/SJ/FK02-2013 TCL 集团多媒体电子全球运营本部 序号: TOT 设计中心 Alignment Procedure MS306C/D Series (MODEL) : VERSION:V1.0 PREPARED BY : gongjunzan DATE : 2013-04-28 APPROVED BY : DATE :...
第 2 页共 11 页 History Description of major changes Release Date V1.0 2013-04-28 1.Overview MS306C/D chassis is designed for Asia Pacific/South America market. Both Full HD panel and HD panel can be compatible. The signal sources include TV,AV,YPBPR/YCBCR,VGA,HDMI USB. YPBPR,HDMI source ,Format up to 1080p can be supported;...
Page 9
第 3 页共 11 页 4-WHITE BALANCE White Balance data adjustment(refer as follow) The balance data is set by PE before the mass production. Do not need adjust. 5-SHOP Reset after production alignment;(This operation will remove all unnecessary factory value; The factory hotkey will be turn off) 6-NVM reset System initialization.
Page 10
R-OFFSET G-OFFSET G-OFFSET B-OFFSET B-OFFSET WB INIT ONLY FOR TCL R&D The first step is to adjust HDMI. 3.Design Menu 1、Methods of Entering: Method 1: Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 1,9,5,and 0 in series ,Design Menu will appear in the left top of screen.
Page 11
第 5 页共 11 页 3-SHOP INIT Default setting submenu after production alignment refer to ** 4-OTHER Other set .Only for TCL R&D 5-SERVICE After service menu description MENU 6-PARAM Parameter setting submenu SETTING 7-HOTEL adjust) Hotel submenu(not MENU SHOP INIT submenu...
第 6 页共 11 页 DBC adjust DBC ENABLE DBC MODE MIU DQS0 MIU DQS1 PARAM SET SETTING ITEMS Default Description Status Setting Brightness Brightness curve. Exclusively used by R&D Curve Contrast Contrast curve. Exclusively used by R&D Curve Saturation Saturation curve.
Page 13
第 7 页共 11 页 Chassis MS306 Chassis name PANEL NAME P/N of panel PROJECT ID Project Select submenu CONFIG Project Select submenu USB UPDATE USB UPDATE HOTEL ENABLE HOTEL MENU SWITCH ReloadEFBItem Only for factory adjust CONFIG submenu ITEM Default Description Status...
Page 14
第 8 页共 11 页 initialize the set. Note: After step 9, Hotel Menu will be disabled by default. Therefore, if the order requires hotel function, it is necessary to enable hotel function by set Design MENU->Service Menu->HOTEL ENABLE to ON. 5.2.
Page 15
第 9 页共 11 页 5.4. White Balance adjustments (Manual) Before adjustment ,you must make sure the ADC status(only PC and YPbPr) “success”and Color Analyzer been calibrated .Only AV1,YPbPr,PC,HDMI1 need to be adjusted. HDMI1 should be the first. 5.4.1. Signal and generator The pattern of the signal should be used are White (Chroma2329 pattern 113) and Grey (pattern 114).
The process of adjusting ADC and White Balance automatically is out of the range of this file, Please refer to the relevant technical file of HuiZhou factory of TCL. 6.Chip list of software programming before SMT Following chips must be programmed before SMT by tools...
Page 17
第 11 页共 11 页 4) Press the right or left button of the remote to select the ID you want; 5) After ID selection, press MENU button of the remote to exit DESIGN MENU. 6) Finally, do AC power on/off.
Page 25
Trouble shooting 1、 Can not switch on: no switch on Check 3.3V/12V/24V of power supply Check PW Only 3.3V Check signal P—ON, Check DC-DC DIMBL—ON of main IC link part,check to PW Check the peripheral circuit of mail IC,check solder of Check reset Check IIC bus main IC,check data fo NVM...
Page 26
2、abnormal picture : Abnormal picture Individual signal source All signal source bad Check the path with this Check panel ID? signal source Check LVDS signal to main Check the peripheral circuit IC?check LVDS cable? of mail IC,updating SW,reset NVM,replace main IC Check crystal frequence?...
Page 27
3、 Abnormal sound: Abnormal sound Individual sound Check all sound signal source source Check the sound signal Check sound IC link to main IC Check the power of Check the peripheral Check wave filter and sound IC circuit of main IC,SW speaker?...
Page 28
H3-28B250SKS-PE0 LED28B2500/MS306D-LA/CS2GTA/TT E3 V1 parent child description BOM text H3-28B250SKS-PE0 06-520W37-C002X RCT NO LOGO BLACK 3V 0.3A 0.000003A 1137 H3-28B250SKS-PE0 T8-28B250KS-IR1 ASS'Y - IR BD T8-28B250KS-IR1 02-IRR002-XX2 IR RECEIVER 38KHZHZ 5V TXZOZ HS0038B4 T8-28B250KS-IR1 12-BT3904-0BX TR-SMD NPN 40VV 200MA_A 300HZ 0.25W SOT2...
Page 38
T8-28B250K5-FC1 59-731110-000 RAW BUFFER 28B2500 0 0 R=Y 贴于前壳上 T8-28B250K5-FC1 59-731120-000 RAW BUFFER 28B2500 0 0 R=Y 贴于前壳左 T8-28B250K5-FC1 63-B30060-BF4G SCREW 固定接收板 T8-28B250K5-FC1 T8-28B250K5-FC1Z ASS'Y - FRONT CABINET ART T8-28B250K5-FC1Z 55-730330-0HX9A DEC FRONTPANEL D10 01 8G 00 R=N T8-28B250K5-FC1Z 56-725510-0HC21 PAI LENS IR L32F3300B -- 00 00 00 R=Y T8-28B250K5-FC1 89-604792-JZH SUNDRIES-FILM SELF ADHESIVE FILM...
Page 39
T8-28B250KG-BS1Z 56-730390-0HA6R DEC STAND BASE PLATE -- 00 00 00 R=N T8-28B250KG-BS1 89-604792-JZ06 SUNDRIES-FILM 0.05X250 SELF ADHESIVE FIL FOR STAND T8-28B250KG-BS1 89-604820-JZ0 PROTECTING LABEL 55mm H3-28B250SKS-PE0 V6-PROJECT-ID001 SOFTWARE PROJECT ID: 01 H3-28B250SKS-PE0 71-BAR030-0A0 PRI LABEL TCL WHITE & BLACK R=Y FOR CTV...
Need help?
Do you have a question about the LED28B2500 and is the answer not in the manual?
Questions and answers