Related Manuals for Liberty Intelix INT-AS2H1U-TX
Summary of Contents for Liberty Intelix INT-AS2H1U-TX
- Page 1 INT-AS2H1U-TX Owners Manual Rev 190812 11675 Ridgeline Drive Phone: 719-260-0061 Colorado Springs, CO Toll-Free: 800-530-8998 80921 Fax: 719-260-0075...
- Page 2 INT-AS2H1U-TX Owners Manual Important Safety Instructions » Please completely read and verify you understand all instructions in this manual before operating this equipment. » Keep these instructions in a safe, accessible place for future reference. » Heed all warnings. » Follow all instructions. »...
-
Page 3: Table Of Contents
INT-AS2H1U-TX Installation Guide Table of Contents Product Overview ��������������������������������������������������������������������������������������������������������������������������������������� Product Contents ���������������������������������������������������������������������������������������������������������������������������������������� Front and Rear Panels ��������������������������������������������������������������������������������������������������������������������������������� Front Panel ���������������������������������������������������������������������������������������������������������������������������������������������������� Rear Panel ���������������������������������������������������������������������������������������������������������������������������������������������������� Installation Instructions ������������������������������������������������������������������������������������������������������������������������������ Mount the Matrix ����������������������������������������������������������������������������������������������������������������������������������������� Connect Sources �������������������������������������������������������������������������������������������������������������������������������������������� Video Inputs ............................Connect Displays ������������������������������������������������������������������������������������������������������������������������������������������� HDMI Output ............................HDBaseT Output ............................. -
Page 4: Product Overview
INT-AS2H1U-TX Owners Manual Product Overview The Intelix INT-AS2H1U-TX is a 3x1 A/V auto switcher that features two HDMI inputs, one USB-C input, one HDMI output, one HDBaseT output and one balanced analog audio output. The USB-C input supports ALT-DP mode and can also charge a connected source device up to 40 watts. The built in... -
Page 5: Front And Rear Panels
INT-AS2H1U-TX Installation Guide Front and Rear Panels Front Panel 1. FW - Illuminates solid RED when switcher is in standby mode or illuminates GREEN when device is powered ON. 2. STATUS LEDs • POWER - Illuminates solid RED when switcher is ON, no LED is shown when switcher is OFF •... -
Page 6: Rear Panel
INT-AS2H1U-TX Owners Manual Rear Panel 1. INPUT • HDMI 1 - HDMI 1 input • HDMI 2 - HDMI 2 input • USB C - USB-C input (supports ALT-DP video mode) 2. OUTPUTS • HDMI - HDMI output • HDBT - HDBaseT output (mirrors HDMI) •... -
Page 7: Installation Instructions
INT-AS2H1U-TX Installation Guide Installation Instructions Mount the Matrix Attach the supplied mounting clips to the sides of the INT-AS2H1U-TX. At least 2 inches of free air space is required on both sides of the INT-AS2H1U-TX for proper side ventilation. Avoid mounting the INT- AS2H1U-TX near a power amplifier or any other source of significant heat. -
Page 8: Connect Audio
INT-AS2H1U-TX Installation Guide Connect Audio Connect an audio amplifier to the audio output of the INT-AS2H1U-TX, the switcher features a line level left and right balanced stereo audio output. The outputs can be wired as unbalanced by only using the positive leads. Connecting RS232 Control RS232 Port Wiring Connect a control system to the INT-AS2H1U-TX via RS232 for switcher control. -
Page 9: Connecting Ir Control
INT-AS2H1U-TX Installation Guide Connecting IR Control Passing IR Signals The INT-AS2H1U-TX is capable of passing IR signals between 33 and 55 KHz. To prevent damage to any of the electronics, the switcher and/or connected extender should be powered off while inserting or removing any IR components. -
Page 10: Configuring Cec And Rs232 Display Automation
INT-AS2H1U-TX Installation Guide Configuring CEC and RS232 Display Automation Automatic Display ON - CEC To automatically turn ON a connected display via CEC when an active input is connected to the inputs, slide the CEC mode switch to the AUTO position on the front of the INT-AS2H1U-TX switcher. In CEC AUTO mode, once an active video source has been connected to the switchers video inputs, the display connected to the HDBaseT receiver via HDMI will be turned ON via CEC. -
Page 11: Hdbaset Cabling Requirements
HDBaseT reliably over longer distances. When using shielded category cabling ALWAYS..use shielded connectors ..properly ground the category cable For optimized HDBaseT performance use the following Liberty Wire and Cable branded cabling; Category 6 plenum; 24-4P-P-L6SH Category 6A plenum; 24-4P-P-L6ASH Category 6 NON-plenum;... -
Page 12: A/V Diagram
INT-AS2H1U-TX Installation Guide A/V Diagram HDMI Source IR Remote Laptop Control System (USB-C) Audio INT-HD70-RX Display (not included) HDMI AUDIO RS232 Display... -
Page 13: Web Gui Control / System Settings
INT-AS2H1U-TX Installation Guide Web GUI Control / System Settings Switcher Control and Configuration Connecting to Web GUI Control Network a PC computer and the INT-AS2H1U-TX then open a web browser and type in IP address of the INT-AS2H1U-TX. The default IP address is 192.168.0.178. -
Page 14: Video Switching
INT-AS2H1U-TX Installation Guide Video Switching The Video menu allows you to route A/V signals to the HDMI and HDBaseT outputs of the switcher simultaneously and enable / disable auto switching mode. By default the INT-AS2H1U-TX is set to auto switching mode. To switch the video route for the switcher, check the HDMI 1, HDMI 2 or USB-C buttons, then press CONFIRM. -
Page 15: Hdcp Configuration
INT-AS2H1U-TX Installation Guide HDCP Configuration The Configuration menu allows you to set the HDCP mode of the INT-AS2H1U-TX Set the HDCP mode to either PASSIVE or ACTIVE • PASSIVE = Automatically follows the HDCP version of the source device selected •... -
Page 16: Device Baud Rate Configuration
INT-AS2H1U-TX Installation Guide Device Baud Rate Configuration The Configuration menu allows you to set the baud rate of the INT-AS2H1U-TX so it can be controlled by 3rd party control device. Select the desired baud rate of the device using the drop down menu labeled DEVICE BAUD RATE... -
Page 17: Edid Management
INT-AS2H1U-TX Installation Guide EDID Management EDID can be set for each input using the EDID menu. To adjust an inputs EDID option, click on the desired input channel, HDMI 1, HDMI 2 or USB-C, then choose the desired resolution option that is available. NOTE: Not all EDID tables will be available for USB-C input Copying and setting EDID from a connected display can be done by selecting the HDMI OUT and HDBT OUT options. -
Page 18: Rs232 Display Control Configuration
INT-AS2H1U-TX Installation Guide RS232 Display Control Configuration RS232 auto display ON/OFF control mode settings can be adjusted by using the RS232 menu. Automatic display ON operation mode can be turned on by sliding the ON button next to DISPLAY CONTROL. NOTE: In order to engage this feature for CEC ON/OFF display control, switch the CEC AUTO/MAN dipswitch on the front of the INT-AS2H1U-TX to the AUTO position. - Page 19 INT-AS2H1U-TX Installation Guide To set the NO signal / NO activity timers ON or OFF, check the ON/OFF button for each option. Specify the time in minutes to which the timers will expire. To save the current selections click SAVE� By default both options are OFF.
-
Page 20: Explanation Of Display On/Off Control Parameters
INT-AS2H1U-TX Installation Guide Explanation Of Display On/Off Control Parameters HEX: Check this box if using HEX formatted strings, by default this is unchecked and any command entered is transmitted in ASCII format. When using HEX formatted strings, there is no need for prefix or suffix identifiers, ie 02h 01h or 0X01, 0x02 etc. -
Page 21: Network Configuration
INT-AS2H1U-TX Installation Guide Network Configuration The Network menu allows you to set the network settings for the device. Navigate to the Network menu, select either DHCP or STATIC IP as the desired IP mode. If choosing DHCP, make sure the INT-AS2H1U-TX is connected to a router / network switch with DHCP server support. -
Page 22: Security
INT-AS2H1U-TX Installation Guide Security The Password menu allows you to set the admin password to a user defined password as well as lock or unlock the front panel buttons of the INT-AS2H1U-TX Navigate to the Security menu, enter in a user defined password in the password field, then click CONFIRM. -
Page 23: Rs232 And Tcp/Ip Control
INT-AS2H1U-TX Installation Guide RS232 and TCP/IP Control RS232 Settings: 9600 baud, 8 Data bits, 1 Stop bit, Parity = None TCP/IP Settings: User defined IP address (default IP address:192.168.0.178), port 4001 There are no spaces between any of the characters in the command string. The commands are case sensitive. All commands are terminated with a carriage return (CR) and line feed (LF). -
Page 24: Autoswitching / Routing
INT-AS2H1U-TX Installation Guide Autoswitching / Routing Description Command Examples #SET_AUTO_SWITCH EN Command: Enable autoswitching mode #SET_AUTO_SWITCH EN<CR><LF> Response: @AUTO_SWITCH ENABLE<CR><LF> #SET_AUTO_SWITCH DIS Command: Disable autoswitching mode #SET_AUTO_SWITCH DIS<CR><LF> Response: @AUTO_SWITCH DISABLE<CR><LF> #SET_AUTO_SWITCH TMDS Command: Enable TMDS switching mode. #SET_AUTO_SWITCH TMDS<CR><LF> Switches based on video signal presence Response:... -
Page 25: Audio Control
INT-AS2H1U-TX Installation Guide Audio Control Description Command Examples #SET_IIS ON Command: Turns the stereo analog L/R #SET_IIS ON<CR><LF> audio output ON Response: @IIS OUT ON<CR><LF> #SET_IIS OFF Command: Turns the stereo analog L/R #SET_IIS OFF<CR><LF> audio output OFF Response: @IIS OUT OFF<CR><LF> #GET_IIS Command: Query audio status... -
Page 26: Rs232 Automatic Display Configuration
INT-AS2H1U-TX Installation Guide RS232 Automatic Display Configuration Description Command Examples #SET_DISPLAY_CTL EN Command: Enables automatic display #SET_DISPLAY_CTL EN<CR><LF> ON control Response: @DISPLAY_CTL ENABLE<CR><LF> #SET_DISPLAY_CTL DIS Command: Disables automatic display #SET_DISPLAY_CTL DIS<CR><LF> ON control Response: @DISPLAY_CTL DISABLE<CR><LF> #SET_NO_SIG 1 {T} Command: Enables automatic display #SET_NO_SIG 1 015<CR><LF>... - Page 27 INT-AS2H1U-TX Installation Guide RS232 Automatic Display Configuration - continued Description Command Examples #SET_ON_A:{S} Command: Sets display ON command #SET_ON_A:PWON<CR><LF> in ASCII format {S} = ASCII STRING Response: @SET_ON_A: PWON<CR><LF> #SET_OFF_A:{S} Command: Sets display OFF command #SET_OFF_A:PWOFF<CR><LF> in ASCII format {S} = ASCII STRING Response: @SET_OFF_A: PWOFF<CR><LF>...
-
Page 28: Rs232 / Cec Display On/Off Control
INT-AS2H1U-TX Installation Guide RS232 / CEC Display On/Off Control Description Command Examples #SET_DISPLAY ON Command: Turns display ON via #SET_DISPLAY ON<CR><LF> CEC or RS232. Sends stored ON Rs232 Response: command to HDBaseT @DISPLAY ON<CR><LF> receivers RS232 port #SET_DISPLAY OFF Command: Turns display OFF via #SET_DISPLAY OFF<CR><LF>... -
Page 29: Rs232 Pass Through Control
INT-AS2H1U-TX Installation Guide RS232 Pass Through Control Description Command Examples #SET_RS232_BAUD [B] Command: Sets baud rate of local switcher #SET_RS232_BAUD 3 RS232 port <CR><LF> {B}(BAUD RATE) = 1-7 Response: 1 = 2400 @RS232_BAUD 3 <CR><LF> 2 = 4800 3 = 9600 4 = 19200 5 = 38400 6 = 57600... - Page 30 INT-AS2H1U-TX Installation Guide RS232 Pass Through Control - continued Description Command Examples #SET_ON_A_1:{S} Command: Transmit ASCII serial string to #SET_ON_A_1:PWON<CR><LF> HDBaseT receivers RS232 port {S} = ASCII STRING Response: @SEND_A_1: PWON<CR><LF> #SET_ON_H_1:{H} Command: Transmit HEX serial string to #SET_ON_H_1:D1 D2 D3<CR><LF> HDBaseT receivers RS232 port {H} = HEX STRING Response:...
-
Page 31: System Commands
INT-AS2H1U-TX Installation Guide System Commands Description Command Examples #SET_POWER ON Command: Turns switcher ON #SET_POWER ON<CR><LF> Response: @POWER ON<CR><LF> PWOFF. Command: Turns switcher OFF #SET_POWER OFF<CR><LF> Response: @POWER OFF<CR><LF> #GET_POWER Command: Query power status #GET_POWER <CR><LF> Response: @POWER ON OR @POWER OFF<CR><LF> #REBOOT Command: Reboots switcher... -
Page 32: Technical Specifications
INT-AS2H1U-TX Installation Guide Technical Specifications Video Video Inputs (2) HDMI, (1) USB-C Video Input Connectors (2) HDMI Type A Female, (1) USB-C 3.0 Input video Signal HDMI for HDMI input, ALT-DP Mode for USB-C HDMI Input Resolution Support Up to 4Kx2K@60Hz 4:2:0 / 8 bit deep color USB C Input Resolution Support Up to 4Kx2K@30Hz 4:2:0 / 8 bit deep color Video Output... - Page 33 Thank you for your purchase. For Technical Support please call our toll free number at 800-530-8998 or email us at supportlibav@libav.com www.libav.com Digitalinx is a brand of:...
Need help?
Do you have a question about the Intelix INT-AS2H1U-TX and is the answer not in the manual?
Questions and answers