Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DURKOPP ADLER DAC eco M-Type
Summary of Contents for DURKOPP ADLER DAC eco M-Type
- Page 1 DAC eco M-Type Instructions for use...
- Page 2 IMPORTANT: READ CAREFULLY BEFORE USE KEEP FOR LATER REFERENCE All rights reserved. Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents, including excerpts, is prohibited without the prior written consent of Dürkopp Adler AG. Copyright © Dürkopp Adler AG 2015...
-
Page 3: Table Of Contents
Setting positions .................. 24 Electrical connection ................ 27 Connecting the power supply .............. 27 Troubleshooting ................29 Customer service ................29 Error messages ................... 29 Glossary ..................... 33 Appendix .................... 35 Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 4 Table of Contents Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 5: About These Instructions
About these instructions About these instructions These instructions for the DAC eco M-Type controller were com- piled with the utmost care. They contain information and notes to enable long-term and reliable operation. Should you notice any discrepancies or if you have improvement requests, we would be glad to receive your feedback through Customer service (... - Page 6 Special attention must be paid to this point when performing a step. Information Additional information, e.g. on alternative operating options. Order Specifies the work to be performed before or after a setting. References Reference to another section in the instructions. Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 7: Other Documents
Leave controllers, equipment and packaging material in the con- dition in which they were found when the damage was discovered. This will ensure any claims against the transport company. Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 8 About these instructions Report all other complaints to Dürkopp Adler immediately after receiving the product. Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 9: Performance Description
Rating and usage conditions Data / motor type Unit Built-in motor Rating Line voltage 190 – 250, single phase Line frequency [Hz] 50/60 Rated power Speed 3400 [min of the motor Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 10 Built-in motor Operating mode (Intermittent periodic duty with electric braking, relative duty cycle 40%, length 2.5 s) IP class IP40 Insulation class Usage conditions Ambient temperature [°C] + 5 – 50 Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 11: Safety
Basic safety instructions The DAC eco M-Type controller may only be used as described in these instructions. The instructions should be available at the controller's location at all times. -
Page 12: Signal Words And Symbols Used In Warnings
Signal words and symbols used in warnings Warnings in the text are distinguished by color bars. The color scheme is oriented towards the severity of the danger. Signal words indicate the degree of risk: Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 13 Symbols The following symbols indicate the type of risk to personnel: Symbol Type of danger General risk Electric shock Puncturing Crushing Environmental damage Instructions for use DAC eco M-Type - 01.0 - 10/2015...
- Page 14 This is what a warning looks like where non-compliance could result undesirable consequences, such as loss of data or damage to hardware. NOTE Tip. This is the more detailed information to simplify operation for the user. Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 15: Components And Functions
When delivered the DAC eco M-Type consists of: • Foot pedal rods • Setpoint device • Controller Controller Fig. 1: Controller front ③ ① ② (1) - Button S1 (3) - Potentiometer (2) - Button S2 Instructions for use DAC eco M-Type - 01.0 - 10/2015... -
Page 16: Setpoint Device
• a push/pull rod (1) that is connected to the machine foot pedal through the set of rods. • a spring preload (2), enabling 3 settings for the push/pull rod (none, 1/8, or 1/4 rotation) Instructions for use DAC eco M-Type - 01.0 - 10/2015... -
Page 17: Proper Use
(3) - Mounting parts (2) - Spring pre-load Proper use The DAC eco M-Type controller is not a standalone unit; instead, it is intended for installation in a machine of the class M-Type with the subclass’ suffix M. For additional information refer to ... - Page 18 Components and functions Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 19: Operation
Operation Operation Operation of the DAC eco M-Type controller is provided exclu- sively by using buttons S1 and S2 as well as the potentiometer. You set the foundation for the sewing process with the settings on the controller. Initial start-up Before initial start-up of the controller, make sure to follow all information in chapter ... - Page 20 Fig. 3: Switching the controller on and off ① ② ⑤ ④ ③ (1) - POWER-LED (4) - LED S2 (2) - MESSAGE-LED (5) - LED S1 (3) - Main switch Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 21: Using Buttons
You will recognize whether a machine function has been activated by the LED in the respective button. When the POWER LED is on you can sew. Programming is possible outside of sewing only ( S. 20). Instructions for use DAC eco M-Type - 01.0 - 10/2015... -
Page 22: Using The Potentiometer
Flashing Flashing Parameters Min. Max. Unit LED S1 ≙ LED S2 ≙ Soft start stitch count Soft start speed 1000 [rpm] Max. speed 3400 1000 [rpm] Holding force Needle position Instructions for use DAC eco M-Type - 01.0 - 10/2015... -
Page 23: Setting The Soft Start Stitch Count
LED S1 flashes for the tens digit, and LED S2 for the units digit. Press and hold button S1 to confirm input. Press and hold button S2 to return to sewing mode. Instructions for use DAC eco M-Type - 01.0 - 10/2015... -
Page 24: Setting The Speed
The value increases or decreases incrementally by one one-hundredth step. LED S1 flashes for the thousands digit, and LED S2 for the hundreds digit. Press and hold button S1 to confirm input. Instructions for use DAC eco M-Type - 01.0 - 10/2015... -
Page 25: Setting The Holding Force
Briefly press button S1 four times. LED S1 flashes briefly four times. Press and hold button S1. The MESSAGE LED illuminates. Press button S1 repeatedly until the required holding force is obtained. Instructions for use DAC eco M-Type - 01.0 - 10/2015... -
Page 26: Setting Positions
To set the reference position: Briefly press button S1 five times. LED S1 flashes briefly five times. Press and hold button S1. The MESSAGE LED, LED S1, and LED S2 illuminate. Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 27 Turn handwheel until the needle below changes direction. Press and hold button S1 to confirm input. LED S1 flashes. Either continue by setting position 2 or exit the parameter while keeping button S2 pressed. Instructions for use DAC eco M-Type - 01.0 - 10/2015...
- Page 28 To set the position 2: Turn handwheel until the needle above changes direction. Press and hold button S1 to confirm input. Press and hold button S2 to return to sewing mode. Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 29: Electrical Connection
( 9 Appendix, S. 35). Always use a multi-prong plug with protective ground contact. The following are suitable power supply nets: • TN net • TT net • IT net Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 30 Electrical connection Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 31: Troubleshooting
Internet: www.duerkopp-adler.com Error messages The DAC eco M-Type controller has 3 types of error messages displayed with the MESSAGE LED. The codes are displayed by means of the MESSAGE LED flashing for an appropriate period at specific intervals. After a brief pause the flashing repeats. - Page 32 Error Sewing motor • Eliminate stiff move- blocked ment in the machine Error Sewing motor over- • Eliminate stiff move- load ment in the machine Instructions for use DAC eco M-Type - 01.0 - 10/2015...
- Page 33 • Update the software Error Low voltage warning • Check the line volt- (2nd threshold): Live voltage < 150 V • Stabilize the line voltage • Use generator Instructions for use DAC eco M-Type - 01.0 - 10/2015...
- Page 34 Information No valid data on • Check machine ID external connection EEprom • Switch off the con- troller, wait until the LEDs are off and then switch on again • Update the software Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 35: Glossary
Soft start Machine starts at a lower speed Setpoint device Converts the values from the foot pedal into volt- age values Stitch count Indicates the number of stitches per minute Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 36 Glossary Instructions for use DAC eco M-Type - 01.0 - 10/2015...
-
Page 37: Appendix
Appendix Appendix Fig. 4: TN net wiring diagram Fig. 5: TT net wiring diagram Instructions for use DAC eco M-Type - 01.0 - 10/2015... - Page 38 Appendix Fig. 6: IT net wiring diagram Instructions for use DAC eco M-Type - 01.0 - 10/2015...
- Page 40 DÜRKOPP ADLER AG Potsdamer Str. 190 33719 Bielefeld, Germany Germany Phone: +49 (0) 521 925 00 E-Mail: service@duerkopp-adler.com www.duerkopp-adler.com...