Table of Contents
Advertisement
Supplemental Explanations
(Corresponds to firmware version 1.60 or later)
Read This before Starting to Assemble the Product
Thank you very much for purchasing the VG-640/VG-540.
There are a number of supplemental points that need to be added and corrections that need to be made to the
instruction manuals included with the product. We ask that you read the information in this manual and use it in
place of the corresponding locations in the instruction manuals.
Manual name
Affected page
P. 4
P. 15
P. 19 to P. 25
P. 83, etc.
P. 15
P. 57
P. 67
P. 86
P. 89
USER'S MANUAL
P. 97
P. 202
(Only When Using Four Colors)
Title
Page in this
manual
P. 2
P. 2
P. 3
P. 11
P. 11
P. 12
P. 13
P. 14
P. 16
P. 19
P. 21
P. 22
P. 22
P. 24
R2-160617
Advertisement
Table of Contents
Related Manuals for Roland TrueVIS VG-640
Summary of Contents for Roland TrueVIS VG-640
-
Page 1: Table Of Contents
Supplemental Explanations (Corresponds to firmware version 1.60 or later) Read This before Starting to Assemble the Product Thank you very much for purchasing the VG-640/VG-540. There are a number of supplemental points that need to be added and corrections that need to be made to the instruction manuals included with the product. - Page 2 Roland DG Corp. • Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur through use of this product, regardless of any failure to perform on the part of this product.
-
Page 3: Contents
Contents Contents ......................1 Additions and Changes to the Setup Guide ..........2 Addition: 2. Included Items (P. 4)....................2 Change: Adjusting the Ink Tube and Affixing a Label (P. 15) ..........2 Change: Ink Filling (P. 19 to P. 25) ....................3 Additions and Changes to the User's Manual .......... -
Page 4: Included Items
Additions and Changes to the Setup Guide Addition: 2. Included Items (P. 4) The following included item has been added. Included item Cartridge-slot label (for white; 1) * With the factory default settings, this label is affixed to the platen at the location where the front cover opens. -
Page 5: Step 8: Ink Filling
Clean the print heads using TR cleaning liquid." • You must purchase the TR cleaning liquid pouch to be used on P. 24, "4. Fill the machine with TR separately. Purchase them from your authorized Roland DG Corp. dealer. cleaning liquid." Items used in this procedure... - Page 6 Additions and Changes to the Setup Guide Make sure the drain bottle is installed, and then press [ENTER]. P. 13, "Step 3: Installing the Drain Bottle" INSTALL DRAIN BOTTLE The screen shown below appears, and then the machine starts the preparations for the ink filling.
- Page 7 Additions and Changes to the Setup Guide When the screen shown below appears, set the pouch tray in which you have set the TR cleaning liquid pouch in the slot whose number is displayed. 8 colors (CMYKLcLmLkW) 4 colors (CMYK) 7 colors (CMYKLcLmLk) SET CL-LIQUID SET CL-LIQUID...
- Page 8 Additions and Changes to the Setup Guide M E M O • When setting the pouch tray: When the pouch tray is set correctly, the number stops flashing and remains lit. SET CL-LIQUID SET CL-LIQUID Flashing • When removing the pouch tray: When the pouch tray is removed correctly, the number stops flashing and turns off.
- Page 9 Additions and Changes to the Setup Guide Quickly attach the emptied drain bottle to the machine once more. Press [ENTER]. Follow the instructions on the screen to repeat the "SET" and "REMOVE" operations for the pouch tray whose slot number is flashing. Fill the machine with ink.
- Page 10 Additions and Changes to the Setup Guide Set the ink pouch for each color and the TR cleaning liquid pouch (separately purchased item) in the pouch trays. Also use the two pouch trays that you used in step Remove the TR cleaning liquid pouch, and then insert the ink pouch.
- Page 11 Additions and Changes to the Setup Guide When the screen shown below appears, set the pouch tray in which you have set an ink pouch in the ink slot whose number is flashing. When using four colors (CMYK), set the pouch trays in the "2, 4, 6, 8" ink slots. Then, when "1, 3, 5, 7"...
- Page 12 Additions and Changes to the Setup Guide The screen shown below appears. FILLING INK... >>>>> XX:XX Close the ink slot cover. When the screen shown below appears, remove the drain bottle and discard the discharged fluid. EMPTY DRAIN BOTTLE IMPORTANT When you remove the drain bottle, a few drops of discharged fluid may come out of the machine.
-
Page 13: (Precaution When Detaching The Drain Bottle)
Additions and Changes to the User's Manual Addition: Precaution When Detaching the Drain Bottle (P. 83, etc.) The following precaution has been added regarding removing the drain bottle in situations such as when discarding the discharged fluid. (Affected pages: P. 83, P. 84, P. 85, P. 98, P. 105, P. 172, and P. 174) IMPORTANT When you remove the drain bottle, a few drops of discharged fluid may come out of the machine. -
Page 14: Step 6 : Starting Output
Additions and Changes to the User's Manual Addition: Starting Output (P. 57) The following details have been added as work to perform before starting output. Before Starting Output • Remove just the pouch tray for the white ink, shake the pouch tray 50 times (about 20 seconds), and then reinsert this pouch tray. -
Page 15: Out-Of-Ink Warnings
Additions and Changes to the User's Manual Addition: Out-of-ink Warnings (P. 67) Details regarding the use of eight colors (CMYKLcLmLkW) have been added. If Using 8 Colors (CMYKLcLmLkW) or 7 Colors (CMYKLcLmLk) Indicates that ink still remains Flashing Indicates that ink has run out 1 2 3 4 5 6 7 8 If an ink pouch runs out, the number of... -
Page 16: Manual Cleaning
Additions and Changes to the User's Manual (Affected page: P. 89) Before Change Monthly Cleaning Manual Cleaning Perform Manual Cleaning Once a Month or More To keep the stable printing condition at all times, perform manual cleaning once a month or more. Manual cleaning takes approximately 10 minutes. -
Page 17: 86 Timing Of Print Head Care And Maintenance
Additions and Changes to the User's Manual Addition and Change: Damper Cleaning (P. 86, P. 96, and P. 97) "Damper cleaning" has been added under "Care and Maintenance When Uneven Color Occurs." As a result, the timing with which to perform "super cleaning" has been changed. (Affected page: P. -
Page 18: New Addition Damper Cleaning
Additions and Changes to the User's Manual (Affected page: P. 96) Delete If Colors Are Still Uneven If uneven color issues are not resolved even after shaking the pouch trays, perform super cleaning. P. 97 "Super Cleaning" Addition Damper Cleaning If uneven color issues are not resolved even after shaking the pouch trays, perform "damper clean- ing."... - Page 19 Additions and Changes to the User's Manual Press [ ] once, and then press [ ] several times to display the screen shown below. INK CONTORL DAMPER CL. Press [ ]. Select the group of print heads to clean. Use the table shown below to check the group that contains the color for which uneven colors are occurring.
- Page 20 Additions and Changes to the User's Manual When "EMPTY DRAIN BOTTLE" is displayed during cleaning EMPTY DRAIN BOTTLE Remove the drain bottle and discard the discharged fluid. Quickly attach the emptied drain bottle to the machine once more. Press [ENTER]. IMPORTANT When you remove the drain bottle, a few drops of discharged fluid may come out of the machine.
-
Page 21: Super Cleaning
Additions and Changes to the User's Manual (Affected page: P. 97) Before Change Super Cleaning In the following cases, perform "super cleaning." • If ink discharge issues such as dot drop-out are not corrected after performing cleaning using the cleaning function (normal, medium, powerful) or manual cleaning. •... - Page 22 Additions and Changes to the User's Manual (Affected page: P. 97) Before Change When using seven colors (CMYKLcLmLk): Press [ ] then [ ] to display the screen shown below. When using four colors (CMYK): Press [ ] to display the screen shown below. INK CONTORL SUPER CL.
-
Page 23: 170 To P. 175 Procedure From Preparing To Move To Reinstallation
Additions and Changes to the User's Manual Addition: Procedure from Preparing to Move to Reinstallation (P. 170 to P. 175) The following procedure has been added to facilitate the use of the "CIRCULATE INK" menu for movement preparation when you are using eight colors (CMYKLcLmLkW). This procedure is not necessary if you are using seven colors (CMYKLcLmLk) or four colors (CMYK), so skip this procedure in these situations. -
Page 24: 191 To P. 192 A Message Appears
The ink in use may not be a To obtain optimal performance, we recommend PROTECTION product specified by Roland that you use ink specified by Roland DG Corp. ACTIVATED] DG Corp. To purchase ink, contact your authorized Ro- land DG Corp. dealer. - Page 25 FOR PUMP sub power. After you switch off the power, con- super, or automatic cleaning PROTECTION] tact your authorized Roland DG Corp. dealer. while sub power was switched off ) was in progress or during the first ink filling procedure for the machine.
-
Page 26: 202 Specifications
Additions and Changes to the User's Manual Addition and Correction: Specifications (P. 202) "Eight colors" has been added to the ink colors. Type TrueVIS INK 500 cc pouch Colors Eight colors (cyan, magenta, yellow, black, light cyan, light magenta, light black, and white) Seven colors (cyan, magenta, yellow, black, light cyan, light magenta, and light black) Four colors (cyan, magenta, yellow, and black)