Advertisement

Brower Timing Systems
TCi-System
2017
User's Manual

Advertisement

Table of Contents
loading

Summary of Contents for BROWER TIMING SYSTEM TCi-System

  • Page 1 Brower Timing Systems TCi-System 2017 User’s Manual...
  • Page 2: Table Of Contents

    Contents Quick Start Guide Quick Start Guide Operating Your TCi-Timer TCi-PhotoGate Setup Power On/Off 5-10-5 Setup To power up the TCi-Timer, press and hold the On/Off button for 2 seconds. The Manual Start button will Setting Up Your TCi-Smart Start simulate a remote start, and is helpful in learning how TCi-Timer Modes the timer works.
  • Page 3: Operating Your Tci-Timer

    Operating Your TCi-Timer Memory Clear Press and hold both buttons at the same time SEQUENCE # displays for approximately four seconds. Memory will SEGMENT displays the sequential order of clear and the clock will be reset to Sequence the time from split to each recorded event.
  • Page 4: Tci-Photogate Setup

    TCi-PhotoGate Setup Athlete Memory Review To review times, press the Memory Review buttons. Holding down either button will Set up the TCi-PhotoGate units as displayed below at the START, engage the high speed scroll. The sequence SPLIT or FINISH location. Memory Review will adjust accordingly.
  • Page 5: Setting Up Your Tci-Smart Start

    *The TCi-PhotoGate B has three IR power settings indicating the maxi- Setting Up Your TCi-Smart Start mum possible distance between TCi-PhotoGates A & B. Beeps Power Meters Hours of Battery Life 1 Beep 2 Beeps Medium 3 Beeps High Application Tip 1.
  • Page 6 1: START ON MOTION WITH KEYPAD 2: START ON MOTION NO KEYPAD The TCi-Smart Start can be used without the keypad. It works just like THREE OR FOUR POINT STANCE: Mode 1 except the sensor will arm and trigger without pressing buttons on the keypad and no Athlete # is sent to the TCi-Timer.
  • Page 7: Tci-Timer Modes

    TCi-Timer Modes KPH/MPH Mode For both TCi-Timer and TCi-Timer SMARTPHONE KPH/MPH mode calculates kilometers per hour and miles per hour. Use the Mode button to scroll through the mode options. When on the Rule: You must have at least 0.2 seconds desired mode press Enter.
  • Page 8: Frequency Select Mode

    TC-Display Frequency Select Mode MEM/MODE FREQ mode allows the user to change Button the radio frequency of the timing system. This allows two or more TCi Systems to work in the same location. After setting the TCi-Timer radio frequency (0-4), the The TC-Display is a hands free timer that will display a time until a new frequency must also be changed to match time starts.
  • Page 9: Split Interval Diagram

    Split Interval Diagram The user is able to navigate the TCi-Timer’s memory using the Up and Down arrows. To review The following diagrams define, Split, Segment and Cumulative times. split times use Split/Scroll arrows. Hold “New” to Memory Review Split/Scroll exit Memory Review.
  • Page 10 Athlete Number Create a start list in the app using existing contact or by adding ath- The “NEW ATHLETE” button is a way to run the TCi-System lete names. Assign an athlete number to each athlete name. The start completely from a Smartphone. Clicking on NEW ATHLETE brings list can be printed or shared through email, text, or data transfer to up a keypad to enter the number of the desired Athlete.
  • Page 11: Troubleshooting

    Troubleshooting Troubleshooting Problem One of my timing units does not power up. If you are still not sure the system is functioning correctly, call us at 801- 572-5540 Solution 1 All units require you to press and hold the power button for at least 2 seconds to initiate the power up sequence.
  • Page 12: Battery Replacement

    TCi-Timer: Remove the battery cover on the lower back of the unit. Install three fresh AAA alkaline batteries. Replace the battery cover. The BROWER TIMING SYSTEM is backed by a 1 year warranty cover- Battery life: 50 hours/40 hours for Smartphone Version ing manufacturing defects.

Table of Contents