Introduction Introduction Thank you for purchasing the Ubiquiti mFi Wall Mount ™ Motion Sensor. This sensor is designed for use with the mFi mPort. Once they are connected, you can use the mFi Controller software to monitor your sensors using your Web browser.
Hardware Installation Hardware Installation Installation Tips • Avoid installing the sensor in areas where it will face direct or reflected sunlight. • Ensure there are no obstructions in the field of view. • Avoid placing the sensor in areas where the environmental temperature may change rapidly.
Page 6
Wall Mount Motion Sensor ™ Wall-Mount Use a 6 mm drill bit to drill two holes 20 mm apart with one directly above the other. 20 mm Insert the anchors into the holes. Use a Phillips screwdriver to secure a M3x20 Screw to the top anchor in the wall.
Page 7
Hardware Installation Align the top hole of the Mounting Bracket over the screw and slide the Mounting Bracket down. Use the Phillips screwdriver to secure the second M3x20 Screw through the bottom of the Mounting Bracket into the anchor.
Page 8
Wall Mount Motion Sensor ™ Connecting the Cabling and Mounting Base Connect a straight-through CAT5/6 cable to the mFi RJ45 port on the mFi-MSW. Secure the mFi-MSW to the Mounting Base using the two M2.6x8 mm Screws.
Page 9
RJ45 port on the mFi mPort. Refer to the User Guide on the CD-ROM that was included with your mFi mPort for instructions on configuring the mFi-MSW in the mFi Controller software. The User Guide can also be downloaded from our website www.ubnt.com/mfi...
Wall Mount Motion Sensor ™ Jumper Settings The mFi-MSW has jumpers located inside the product casing. Typically there is no need to open the casing to adjust the jumpers. The SENS and LED jumpers are the only ones that you may want to change. The SENS jumper can be changed to reduce the sensitivity of the microwave sensor.
Page 11
If you need to access the jumper settings, use a Phillips screwdriver to remove the screw at the base of the sensor. Lift the case up and the jumpers will be accessible. The LED is disabled by default and can only be enabled by opening the product case and adjusting the jumper.
Buyer for breach of warranty and shall constitute fulfillment of all liabilities of UBIQUITI NETWORKS with respect to the quality and performance of the Products. UBIQUITI NETWORKS reserves the right to inspect all defective Products (which must be returned by Buyer to UBIQUITI NETWORKS factory freight prepaid).
(II) No modification, alteration or addition has been made to the Product by persons other than UBIQUITI NETWORKS or UBIQUITI NETWORK’S authorized representatives or otherwise approved by UBIQUITI NETWORKS.
Page 16
Wall Mount Motion Sensor ™ Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired...
Page 17
Compliance This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de la classe A est confrome à...
Page 18
Wall Mount Motion Sensor ™ L’émetteur-récepteur décrit ici émet de l’énergie de fréquence radio. Bien que le niveau de puissance est faible, l’énergie concentrée à partir d’une antenne directionnelle peut présenter un danger pour la santé. Ne pas permettre aux gens de se rapprocher de 20 cm à l’antenne lorsque l’émetteur est en marche.
Page 19
Compliance RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Declaration of Conformity Česky UBIQUITI NETWORKS tímto prohla uje, e tento [Czech] UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk Undertegnede UBIQUITI NETWORKS erklærer herved, [Danish] at følgende udstyr UBIQUITI NETWORKS device,...
Page 21
UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Íslenska Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI [Icelandic] NETWORKS device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í tilskipun 1999/5/EC.
Page 22
Wall Mount Motion Sensor ™ Latviski Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI [Latvian] NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem. Lietuviškai UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI [Lithuanian] NETWORKS įrenginys atitinka esminius reikalavimus ir...