Advertisement
Quick Links
Installation Instructions
Original Instructions
PanelView Mounting Levers
Catalog Number 2711P-RMCP
Topic
Use these mounting levers with these terminals:
• PanelView™ Plus 7 Performance terminals
• PanelView 5310 terminals
• PanelView 5500 terminals
• PanelView 5510 terminals
Summary of Changes
This publication contains new and updated information as indicated in the following table.
Topic
Changed part number from PN-411643 to PN-496931.
Page
1
2
3
5
8
Page
8
Advertisement
Related Manuals for Rockwell Automation Allen-Bradley PanelView Series
Summary of Contents for Rockwell Automation Allen-Bradley PanelView Series
-
Page 1: Table Of Contents
Installation Instructions Original Instructions PanelView Mounting Levers Catalog Number 2711P-RMCP Topic Page Summary of Changes Prepare for Panel Mounting Mounting Lever Orientation and Lock Sequence Mount the Terminal in a Panel Additional Resources Use these mounting levers with these terminals: •... -
Page 2: Prepare For Panel Mounting
Panel Thickness Range Gauge 1.50…2.01 mm (0.060…0.079 in.) 1 2 3 4 2.03…2.64 mm (0.080…0.104 in.) Notch 2.67…3.15 mm (0.105…0.124 in.) 3.17…3.66 mm (0.125…0.144 in.) 3.68…4.16 mm (0.145…0.164 in.) Alignment Mark 4.19…4.80 mm (0.165…0.188 in.) Rockwell Automation Publication VIEW-IN001C-EN-P - April 2018... -
Page 3: Mounting Lever Orientation And Lock Sequence
The mounting lever orientations that are shown are required to maintain NEMA, UL Type, and IP seals. If you require a NEMA, UL Type, or IP seal, do not use a mounting lever in other orientations. Rockwell Automation Publication VIEW-IN001C-EN-P - April 2018... - Page 4 The mounting lever orientations that are shown are required to maintain NEMA, UL Type, and IP seals. If you require a NEMA, UL Type, or IP seal, do not use a mounting lever in other orientations. Rockwell Automation Publication VIEW-IN001C-EN-P - April 2018...
-
Page 5: Mount The Terminal In A Panel
Tilt the terminal toward the panel cutout and guide the terminal upward into the cutout; make sure that the mounting levers stay intact. The mounting levers in the top corner slots help to stabilize the terminal in the panel while you install the remaining mounting levers. Rockwell Automation Publication VIEW-IN001C-EN-P - April 2018... - Page 6 3 for the locking sequence of your terminal model. c. Rotate each mounting lever until the flat side comes in contact with the panel. Flat Side in Contact With the Panel Flat Side Rockwell Automation Publication VIEW-IN001C-EN-P - April 2018...
- Page 7 ATTENTION: All mounting levers must be in the correct locked position and follow the correct lever installation sequence to provide an adequate gasket seal between the terminal and the panel. Rockwell Automation assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
-
Page 8: Additional Resources
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, PanelView, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400...