Table of Contents
Advertisement
Quick Links
Installation Instructions
Original Instructions
Kinetix 5700 System Mounting Toolkit
Catalog Number 2198-K5700-MOUNTKIT
Topic
Summary of Changes
This publication contains new and updated information as indicated in the following table.
Topic
Page
1
2
2
2
2
4
5
7
8
11
Page
2
2
2
2
4
5
7
8
11
Advertisement
Table of Contents
Summary of Contents for Rockwell Automation Allen-Bradley 2198-K5700-MOUNTKIT
-
Page 1: Table Of Contents
Installation Instructions Original Instructions Kinetix 5700 System Mounting Toolkit Catalog Number 2198-K5700-MOUNTKIT Topic Page Summary of Changes About the System Mounting Toolkit Parts List Required Tools and Components Install the Mounting Bar and Position the Drill-hole Guide Use the Drill Hole Guide with 165 mm Wide Modules Use the Drill Hole Guide with 220 mm Wide Modules Use the Drill Hole Guide with 275 mm Wide Modules Use the Drill Hole Guide with 440 mm Wide Modules... -
Page 2: About The System Mounting Toolkit
Follow these steps to locate the drill-holes for your Kinetix 5700 drive system. 1. Draw a horizontal line on the panel where you would like to position the upper module-width holes (refer to Figure Rockwell Automation Publication 2198-IN012B-EN-P - February 2019... - Page 3 When drive systems are wider than the mounting bar, you can remove the screws and shift the mounting bar left or right, reusing two of the original holes and drilling another (repeat as needed). 10. Remove the mounting bar from the panel when you are finished. Rockwell Automation Publication 2198-IN012B-EN-P - February 2019...
-
Page 4: Use The Drill Hole Guide With 165 Mm Wide Modules
3. Slide the drill-hole guide into the mounting bar and adjust left-to-right until the 55 mm upper module-width hole is aligned with the vertical line you drew in step 2. 4. Mark top 55 hole and bottom 55 hole locations. Rockwell Automation Publication 2198-IN012B-EN-P - February 2019... -
Page 5: Use The Drill Hole Guide With 220 Mm Wide Modules
The figure is not to scale. 2. Draw a vertical line where left side of module is to be installed. Rockwell Automation Publication 2198-IN012B-EN-P - February 2019... - Page 6 When drive systems are wider than the mounting bar, you can remove the screws and shift the mounting bar left or right, reusing two of the original holes and drilling another (repeat as needed). 16. Remove the mounting bar from the panel when you are finished. The finished marks appear as shown in Figure 4. The figure is not to scale. Rockwell Automation Publication 2198-IN012B-EN-P - February 2019...
-
Page 7: Use The Drill Hole Guide With 275 Mm Wide Modules
11. Shift the template left to align the rightmost line to the leftmost 55 slot. 12. Draw a line in the rightmost 55 slot. 13. Shift the template to align the line you drew in step 12 to the leftmost 55 slot. Rockwell Automation Publication 2198-IN012B-EN-P - February 2019... -
Page 8: Use The Drill Hole Guide With 440 Mm Wide Modules
Figure 6 shows the finished drill-hole map and the steps where each mark was made. The figure is not to scale. Rockwell Automation Publication 2198-IN012B-EN-P - February 2019... - Page 9 (repeat as needed). 32. Remove the mounting bar from the panel when you are finished. The finished marks appear as shown in Figure 6. The figure is not to scale. Rockwell Automation Publication 2198-IN012B-EN-P - February 2019...
- Page 10 Step 2 Step 6 Step 20 Step 22 Step 30 Step 2 Step 16 Step 26 Step 10 Step 12 465 mm Step 24 Step 14 Step 4 Step 8 Step 18 Step 28 Rockwell Automation Publication 2198-IN012B-EN-P - February 2019...
-
Page 11: Additional Resources
Kinetix 5700 System Mounting Toolkit Additional Resources These documents contain additional information concerning related products from Rockwell Automation. Resource Description Provides information on installing, configuring, start up, and troubleshooting your Kinetix 5700 Servo Drives User Manual, publication 2198-UM002 Kinetix 5700 servo drive system. - Page 12 Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, Kinetix, Logix 5000, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400...